Remove/install engine mount - AR22.10-P-1100PV

WARNING: This page does not describe the selected car, but rather 25 other vehicles, including the 2007 Mercedes-Benz C350, 2007 Mercedes-Benz C280, 2007 Mercedes-Benz C230, 2006 Mercedes-Benz C55, and 2006 Mercedes-Benz C350. However, it is still accessible from the selected car via links, so may be relevant.

ENGINE 112.912 in MODEL 203.061 /261, 209.361 /461 with TRANSMISSION 716.6, 722.6

ENGINE 112.946 in MODEL 203.064 /264 with TRANSMISSION 722.6

ENGINE 112.961 in MODEL 203.065 /265 with TRANSMISSION 722.6

ENGINE 113.968 in MODEL 209.375 /475 with TRANSMISSION 722.633

ENGINE 112.913 in MODEL 211.061 /261 with TRANSMISSIONS 716.6, 722.6

ENGINE 112.949 in MODEL 211.065 /265 with TRANSMISSION 722.618

ENGINE 113.967 in MODEL 211.070 /270 with TRANSMISSION 722.633

ENGINE 113.987 in MODEL 209.376 /476 with TRANSMISSION 722.636

ENGINE 112.955 in MODEL 209.365 /465 with TRANSMISSION 722.618

ENGINE 113.990 in MODEL 211.076 /276 with TRANSMISSION 722.643

Shown on engine 112

Fig 1: Identifying Engine Mount Remove/Install Components - Shown On Engine 112

Fig 2: Identifying Cross Strut

MODIFICATION NOTES

16.5.06

"Disconnect/connect battery ground line" removed

	Remove/install
	Risk of death caused by vehicle slipping or toppling off the lifting platform.	Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer.	AS00.00-Z-0010-01A
	Notes on self-locking nuts and bolts		AH00.00-N-0001-01A
1.1	Remove air filter housing (1).	Engine 112.912 /946 /961 in model 203 Engine 112.912 /955 in model 209 Engine 112.913 /949, 113.990 in model 211	AR09.10-P-1150SVK
		Engine 113.987 in model 209.376 /476 as of 24.4.04	AR09.10-P-1150AC
1.2	Unclip cover on front side of engine	Model 209, 211 with engine 113 except AMG
2	Detach lower engine compartment paneling	Model 203, 209	AR61.20-P-1105P
		Model 211	AR61.20-P-1105T
3	Remove bolt (2)	Except engine 112. in model 203	*BA22.10-P-1001-01L
		Engine 112.912/ 946 in model 203	*BA22.10-P-1001-01R
4.1	Remove complete exhaust system	Engine 112 in model 203 Engine 112 in model 209 Engine 113.987 in model 209.376 up to 23.4.04, 209.476 Engine 113.968 in model 209.375 /475	AR49.10-P-7000PV
		Engine 113.987 in Model 209.376 as of 24.4.04	AR49.10-P-7000AC
4.2	Remove front exhaust system from right and left exhaust manifold	Model 211 Installation: Replace bolts and check rivet nuts in the exhaust manifold, replace if required:↓	AR49.10-P-7000TB
		Replace rivet nuts in exhaust manifold.	AR49.10-P-5531-01DA
			*BA14.10-P-1002-01B
			Figure
5	Unscrew bolts (4a)	Model 211
			*BA49.10-P-1011-01A
6	Dismount bracket (4) for exhaust system from transmission	Model 211
7	Remove cross strut (12)	Model 211
8	Mount bracket on supercharger	Engine 112.961, 113.990 For engine lifting device.
9	Fit on engine lifting device	Model 203, 209	AR33.10-P-0100-01P
		Model 211	AR33.10-P-0100-01T
		Model 211	Fig 4
10	Raise engine	When lifting the engine ensure that components are neither pinched or overstretched to avoid causing damage.
11	Remove bolts (5)	Except engine 112. in model 203	*BA22.10-P-1004-01L
		Engine 112.912/ 946 in model 203	*BA22.10-P-1004-01R
12	Remove engine mounts (3)	Remove engine mount (3) from left engine carrier (9) and right engine carrier (10). Remove engine mount (3) with left head shield (6) and right heat shield (7). Installation: Anti-twist locks (8) on engine mounts (3) must latch into retaining grooves in the left engine support (9) and right engine support (10). Anti-twist locks (11) on the right engine support (10) and the left engine support (9) must sit in the cutouts on the left shield (6) and the right shield (7). Pay attention to environmental protection regulations for disposal of engine mounts (3). Dispose engine mounts (3) into mixed scrap.
13	Install in the reverse order
14	Connect STAR DIAGNOSIS and delete fault memory.