Remove/install wheels, rotate if necessary - AP40.10-P-4050Z

MODEL 124, 129, 140, 164, 168, 170, 202, 203, 208, 209, 210, 211, 215, 220, 230, 240 

MODEL 414 

Left illustration 

Fig 1: Identifying Wheel Bolts Tightening Sequence

Courtesy of MERCEDES-BENZ USA

Right figure 

	Removing
	Risk of death  caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer.	AS00.00-Z-0010-01A
1	Hoist vehicle with lifting platform until wheels are free	Model 164	AR00.60-P-1000GZ
		Model 203, 209	AR00.60-P-1000P
		Model 211	AR00.60-P-1000T
2	Pull off wheel covers	Vehicles with wheel covers
3	Unscrew wheel bolts and remove wheel-and-tire assemblies	Model 164, 240: Remove wheel-and-tire assemblies with wheel lift Wheel lift/wheel lift truck	*199589010900
	Wheel bolts modified	Model 210	BT40.10-P-0001-01A
	Check
4	Check tires for damage and condition, measure tread depth and note down measurements on maintenance sheet		AP40.10-P-4051Z
	Information on tires / rims		AH40.10-P-9411-01A
5	Clean and check wheel bolt connection components, then protect against corrosion	Before mounting a wheel-and-tire assembly all  the operation steps listed in the linked description must be conducted carefully. Otherwise the wheel-and-tire assembly may work its way loose from the vehicle and cause damage to people, property or the environment!	AP40.10-P-4050-01A
		Cleaner from package	*BR00.45-Z-1028-04A
		Long-life grease	*BR00.45-Z-1001-06A
	Install
6	Change round wheel-and-tire assemblies on front and rear axles	If necessary, and only on vehicles without mixed tires. Maintain running direction of wheel-and-tire assemblies. Otherwise handling characteristics and handling comfort may be impaired and tire wear increased.
7	Mount wheel-and-tire assembly and tighten wheel bolts	Model 164, 240: Mount wheel-and-tire assemblies with wheel lift Observe the tightening sequence (1 to 5) and tightening torque. Except model 164 and model 210 with code (979) Special protection version	*BA40.10-P-1001-01A
		Model 210 with code (979) Special protection version	*BA40.10-P-1001-01B
		Model 164	*BA40.10-P-1001-01J
	Wheel bolts modified	Model 210	BT40.10-P-0001-01A
8	Lower vehicle
9	Correct tire pressure for all wheel-and-tire assemblies	In the event of tire pressure loss, determine cause and replace valve, tire or rim. On vehicles with tire pressure monitor: Install only valve protection caps made of plastic in order to avoid corrosion. Tire inflation devices - mobile - with / without reservoir
10	Fit wheel covers	Vehicles with wheel covers
11	Activate the tire pressure monitoring system	On vehicles with tire pressure monitor, wherever possible: Only for wheel-and-tire assembly change, tire replacement or a change in tire pressure: ↓ Perform adjustments to the control system Model 164	AR54.30-P-1000-02GZA
		Model 211	AR54.30-P-1000-02RAT
		Model 215, 220	AR54.30-P-1000-02RAM
		Model 230	AR54.30-P-1000-02RAR
		Model 240	AR54.30-P-1000-02RAH
	Tire pressure monitor (RDK) activation	Model 210.074 / 274	GF40.15-P-0001-02A

Fig 2: Identifying Socket Wrench (199 589 01 09 00)

Courtesy of MERCEDES-BENZ USA