LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2008 >> GL320 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 10 (Lubrication, Oil Cooling - 164 Chassis) >> Testing & Repair >> Replace the oil pump chain - AR18.10-P-2140SX (ML350, ML550, GL450, GL550) >> Rivet oil pump chain - AR18.10-P-2140-02TX

Rivet oil pump chain - AR18.10-P-2140-02TX

WARNING: This page does not describe the selected car, but rather 28 other vehicles, including the 2012 Mercedes-Benz GL550, 2012 Mercedes-Benz GL450, 2011 Mercedes-Benz ML63, 2011 Mercedes-Benz ML550, and 2011 Mercedes-Benz ML350. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Identifying Case (602 589 00 98 00)
G07068722Courtesy of MERCEDES-BENZ USA
Fig 2: Identifying Riveting Tool (642 589 00 33 00)
G07068723Courtesy of MERCEDES-BENZ USA
Fig 3: Identifying Thrust Spindle (271 589 10 63 00)
G07068724Courtesy of MERCEDES-BENZ USA
Fig 4: Identifying Assembly Link (271 589 02 40 00)
G07068725Courtesy of MERCEDES-BENZ USA
Fig 5: Identifying Assembly Inserts (271 589 02 63 00)
G07068726Courtesy of MERCEDES-BENZ USA
  1. Connect new oil pump chain (2) and old oil pump chain (1) together using an SPECIAL TOOL assembly link (3)
  2. Slowly rotate crankshaft in the direction of engine rotation (arrow) until it is possible to connect both ends of the new oil pump chain (2).
  3. SPECIAL TOOL Remove assembly link (3) and old oil pump chain (1).
    Fig 6: Rotating Crank Shaft
    G07068727Courtesy of MERCEDES-BENZ USA
  4. Connect ends of new oil pump chain (2) using a riveted link (4). IMPORTANT Insert riveted link (4) from front.
    Fig 7: Identifying Oil Pump Chain And Riveted Link
    G07068728Courtesy of MERCEDES-BENZ USA
  5. SPECIAL TOOL Place assembly insert with digit F10 into SPECIAL TOOL rivet press tool (arrow) and fix in place by a bolt (28).
    Fig 8: Placing Assembly Insert Into Rivet Press Tool
    G07068729Courtesy of MERCEDES-BENZ USA
  6. Place moveable SPECIAL TOOL assembly insert with digit D10 into SPECIAL TOOL rivet press tool (arrow).
    Fig 9: Placing Moveable Assembly Insert Into Rivet Press Tool
    G07068730Courtesy of MERCEDES-BENZ USA
  7. Insert outer plate (5) of the rivet link (4) into the SPECIAL TOOL assembly insert with the digit D10 (arrow).
    Fig 10: Inserting Outer Plate Into Assembly Insert
    G07068731Courtesy of MERCEDES-BENZ USA
  8. SPECIAL TOOL Place rivet press tool on the new oil pump chain (2).

    IMPORTANT Fit in such a way that the rollers of the riveted link (4) rest on the spacer web (arrow).

  9. SPECIAL TOOL Tighten pressure screw (6) until a firm resistance is felt.

    IMPORTANT While turning the SPECIAL TOOL pressure screw (6), ensure that pin in rivet link (4) is inserted in holes in the external mounting link (5).

  10. SPECIAL TOOL Remove rivet press tool.
    Fig 11: Locating Spacer Web
    G07068732Courtesy of MERCEDES-BENZ USA
  11. SPECIAL TOOL Move assembly insert with digit D10 onto rivet profile (arrow).
    Fig 12: Locating Rivet Profile
    G07068733Courtesy of MERCEDES-BENZ USA
  12. SPECIAL TOOL Place rivet press tool on new oil pump chain (2) riveted link (4).

    IMPORTANT Fit the in such a way that pins for the riveted link (4) are located exactly in the center of prism support (arrow).

  13. SPECIAL TOOL Tighten pressure screw (6).

    IMPORTANT The torque applied to SPECIAL TOOL pressure screw (6) is about 30 to 35 Nm (reference value).

  14. Rivet bolts for riveted link (4) individually.
    Fig 13: Locating Prism Support
    G07068734Courtesy of MERCEDES-BENZ USA
  15. INSPECT Test riveted joints (arrow) and rivet the pins again if necessary.
    Fig 14: Locating Riveted Joints
    G07068735Courtesy of MERCEDES-BENZ USA
scientia non olet · About LEMON Manuals