Check and correct the adjustment of the headlamps - AP82.10-P-8260T
MODEL 211
MODIFICATION NOTES
| 15.1.08 | Load driver seat, added | Operation step 7 |
| Check | |||
| Risk of death
caused by high voltage levels present at xenon headlamps. Risk of explosion/fire hazard due to highly flammable substances in the area of damaged xenon bulbs Risk of injury due to UV light, hot components on xenon headlamps and glass splinters when xenon bulbs burst Risk of poisoning caused by inhalation of mercury vapors and by toxic salts and mercury compounds being ingested or coming into contact with skin |
Do not come into contact with parts that are under high voltage. Persons with active electronic implants (e.g. heart pacemakers) must never work on xenon headlamps. Switch off entire lighting system. Wear insulated safety shoes, safety glasses and protective gloves. Remove highly inflammable materials from the hazard area. Ensure sufficient ventilation in the working area. | AS82.10-Z-0001-01A | |
| Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running | Secure vehicle to prevent it from moving by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. |
AS00.00-Z-0005-01A | |
| 1 | Check tire inflation pressure, correct if necessary | ||
| 2 | Park the vehicle on a horizontal, level surface | ||
| 3 | Shift transmission to position "N" and open side window | Vehicles with code 489 Airmatic (semi-active air suspension) | |
| 4 | Get out with the engine running and close driver door | Vehicles with code 489 Airmatic (semi-active air suspension) | |
| 5 | Press switch for level control and raise vehicle level, then lower to normal level | Vehicles with code 489 Airmatic (semi-active air suspension) |
|
| 6 | Connect STAR DIAGNOSIS diagnostic system and set vehicle center to adjustment level | With model 211.2 with standard headlamps without code 489 Airmatic (semi-active air suspension) | *BE82.10-P-1001-01E |
| 7 | One person to occupy the driver seat or load the seat with 75 kg | Except vehicles with code 489 Airmatic (semi-active air suspension) | |
| 8 | Prepare headlamp aimer | Headlamp aimer http://gotis.aftersales.mercedes-benz.com |
|
| 9 | Start the engine and switch on low beam | ||
| 10.1 | Check function of headlamp range adjustment by adjusting headlamp range adjustment switch | Except vehicles with code 614 Bi-xenon headlamp unit and code 615 Bi-xenon headlamp unit with integrated curve illumination |
|
| 10.2 | Check function of headlamp range adjustment through placement of additional weights in the luggage compartment | Vehicles with code 614 Bi-xenon headlamp unit and code 615 Bi-xenon headlamp unit with integrated curve illumination |
|
| 11.1 | Set switch for headlamp range adjustment to position 0 | Except vehicles with code 614 Bi-xenon headlamp unit and code 615 Bi-xenon headlamp unit with integrated curve illumination | |
| 11.2 | Remove additional weights from the luggage compartment | Vehicles with code 614 Bi-xenon headlamp unit and code 615 Bi-xenon headlamp unit with integrated curve illumination | |
| 12 | Check low beam setting and correct if necessary | Connect STAR DIAGNOSIS and move headlamp to zero position. |
AP82.10-P-8260-01A |
| 13 | Check setting of high beam | AP82.10-P-8260-02A | |
| 14 | Check setting of front fog lamps and correct if necessary | AP82.10-P-8260-04A | |
| 15 | Detach STAR DIAGNOSIS | For model 211.2 with standard headlamps without code 489 Airmatic (semi-active air suspension) and following adjustment operations on vehicles with code 614 Bi-xenon headlamp unit and code 615 Bi-xenon headlamp unit with integrated curve illumination | |
| 16 | Switch off light and turn off engine |
TEST VALUES FOR EXTERIOR LIGHTS
| Number | Designation | Model 211.2 without code 489a, 614, 615a | |
|---|---|---|---|
| BE82.10-P-1001-01E | Vehicle level when checking and adjusting the headlamps | mm | +6 |