Car-Bench straightening bench setup - AR60.10-P-1090Y

MODEL 219 

Fig 1: Identifying Car-Bench Straightening Bench

Courtesy of MERCEDES-BENZ USA

	Remove/Install
	Risk of death  caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between the columns of the hydraulic hoist and position the four support plates below the hoist support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
1	Lift vehicle with two-post lift	Two-post lift	*WE58.40-Z-1001-05A
2	Install Car-Bench straightening bench (1)
		Car-Bench straightening bench BT 17	*WE58.40-Z-1003-01E
		Car-Bench straightening bench BT 43/1	*WE58.40-Z-1003-01E
		Car-Bench straightening bench BT 140	*WE58.40-Z-1003-01E
3	Car-Bench modular members		AR60.10-P-1090-01Y
		Car-Bench straightening bench BT 17	*WE58.40-Z-1003-01E
		Car-Bench straightening bench BT 43/1	*WE58.40-Z-1003-01E
		Car-Bench straightening bench BT 140	*WE58.40-Z-1003-01E
		Car-Bench universal crossmember set A 296	*WE58.40-Z-1010-01E
		Car-Bench universal crossmember set	*WE58.40-Z-1011-01E
		A 296/15 (all members 1500 mm long)
		Car-Bench universal crossmember set 296/19	*WE58.40-Z-1059-01A
4	Install Car-Bench straightening tool		AR60.10-P-1090-02Y
		SW19 socket wrench bit, for hexagon bolts	*WH58.30-Z-1010-06A
		Reversible ratchet	*WH58.30-Z-1007-06A
		Pneumatic ratchet driver 1/2	*WE58.40-Z-1008-03A
		Double box wrench, offset, 17 19 mm	*WH58.30-Z-1001-11A
		Car-Bench straightening bracket set 82441 (for model 211)	*WE58.40-Z-1054-01A
5	Remove stop plug from jack tubes
6	Place vehicle on straightening bench
7	Align vehicle on straightening bench	Observe check bore!
8	Attach vehicle to straightening bench
9.1	Instal side portal with portal straightening set (Car-Bench)	Only when the vehicle repair demands it.	AR60.20-P-1060-01Y
		Side portal frame	Figure
		Inspection and welding device	Figure
		Welding devices	Figure
		SW19 socket wrench bit, for hexagon bolts	*WH58.30-Z-1010-06A
		Reversible ratchet	*WH58.30-Z-1007-06A
		Pneumatic ratchet driver 1/2	*WE58.40-Z-1008-03A
		Double box wrench, offset, 17 19 mm	*WH58.30-Z-1001-11A
		Car-Bench straightening bracket set 82441 (for model 211)	*WE58.40-Z-1054-01A

Fig 2: Identifying Side Portal Frame (210 589 17 23 00)

Courtesy of MERCEDES-BENZ USA

Fig 3: Identifying Inspection And Welding Device (211 589 00 23 00)

Courtesy of MERCEDES-BENZ USA

Fig 4: Identifying Welding Devices (219 589 00 23 00)

Courtesy of MERCEDES-BENZ USA

COMMERCIALLY AVAILABLE TOOLS

Number	Designation
WH58.30-Z-1007-06A	Reversible ratchet
WH58.30-Z-1010-06A	Socket SW19 for hexagon head screws
WH58.30-Z-1001-11A	Double end box wrench, offset, 17 x 19 mm

WORKSHOP EQUIPMENT

WE58.40-Z-1054-01A	Car bench straightening bracket set 82441, (model 211)
WE58.40-Z-1059-01A	Car-Bench universal crossmember set 296/19
WE58.40-Z-1003-01E	Car-Bench straightening bench
WE58.40-Z-1010-01E	Car-Bench universal cross member set A 296
WE58.40-Z-1011-01E	Car-Bench Universal crossmember set A 296/15 (all crossmembers 1500 mm long)
WE58.40-Z-1008-03A	Pneumatic ratchet
WE58.40-Z-1001-05A	Two-post lifting platform