LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2008 >> CL550 >> Repair and Diagnosis >> Accessories & Equipment >> Infotainment >> Entertainment, Lighting & Navigation -- Cl550 -- 216 Chassis >> Basic Knowledge >> Mobile phone system, operating instructions - GF82.70-P-0007-07LE

Mobile phone system, operating instructions - GF82.70-P-0007-07LE

These operating instructions consist of the following subfunctions:

Establishing a telephone connection - making a call 

The "Establishing a telephone connection - making a call" subfunction consists of the following subfunctions:

Dialing using keypad on mobile phone 

Hands-free mode is active if the mobile phone keypad is used for dialing. Telephone numbers can be selected from the mobile phone telephone book.

Dialing using the center console button group 

The telephone menu must be activated on the COMAND controller unit (A40/3). The number entered is dialed by pressing the "Send" button. Hands-free mode is active if the center console button group is used for dialing.

Dial using the multifunction steering wheel 

The mobile phone telephone book is selected using the menu on the instrument cluster (A1) display. The name of the person to be called is selected by scrolling forward and back using the scroll forward/ back button (S110s1). The call is activated on the steering wheel using the Accept/terminate phone call button (S111s3).

Dialing by pressing the Send button 

The call list of "Dialed numbers" can be displayed and numbers dialed from it.

Dialing using VCS [SBS] 

The VCS [SBS] is activated by pressing the VCS [SBS] on button (S111s4). An acoustic signal is emitted after activation has taken place.

Voice commands are e.g.:

Dialing using MMS 

The MMS telephone function can be selected via the "Tel" menu or via the Telephone/Navigation quick select button (A40/9s5) on the front central operating unit (A40/9).

The following ways of dialing a telephone number are available to the user here:

The name of the person who you wish to call can be selected in the address book and the call lists by scrolling up and down.

The call is activated using the "SEND" function.

Establishing a telephone connection - receiving a call 

The mobile phone receives a call signal via the telephone and GPS roof antenna (A2/49) (model 221), the telephone antenna (A2/49a1) (model 216 with code (494) USA version) or the telephone and GPS antenna (A2/49) (model 216 without code (494) USA version). The caller is shown on the mobile phone display and this information is simultaneously transmitted to the following control units.

The audio tuner control unit (N93/1) receives the ringing tone and sends the signal to the speaker system.

At the same time it reduces the volume of the currently active audio source (e.g. the radio) by L = 15 dB. The audio source is not muted until the user accepts the call.

Up to 31.5.09:

As of 1.6.09

The call can be answered using the front central operating unit, using the buttons on the mobile phone and using the Accept/terminate phone call button or using the center console button group.

Hands-free mode 

Accepting a call by:

Up to 31.5.09:

As of 1.6.09

Private mode 

When in "private mode" the user can make a telephone call without other vehicle occupants being able to hear the conversation. Up to 31.5.09:

With the UPCI [UHI] (Universal Portable Cell Phone Interface) control unit, "private mode" is also possible using a Bluetooth headset.

"Private mode" is activated by pressing the button on the headset. Pressing the button (once) again ends the call. Pressing a second time within t = 3 s switches into hands-free mode or from hands-free mode back to "private mode" (this function is dependent on the particular headset).

As of 1.6.09: By removing the mobile phone from the UPCI [UHI] (Universal Portable Cell Phone Interface) cell phone holder (A34/15) or the rear handset from the rear handset holder (A34/13) (with code (856) 2nd handset in rear armrest) the phone call is answered in "private mode".

Terminating/aborting/rejecting a call 

The user can terminate the telephone call or reject an incoming call at any time. The user has the following options for terminating or rejecting the connection:

Toggling 

The user can switch back and forth between telephone calls with two people. This function is implemented directly via the mobile phone, the handset in the rear (with code (856) 2nd handset in rear armrest) or the center console button group ("2" button, then "Send" button). While the user talks to one person on the line, the connection to the other is put on hold.

A conference call, i.e. communicating simultaneously with a number of parties, is possible (activate via "3" button, then "Send" button on the center console button group).

Using the front central operating unit, the multifunction steering wheel and the center console button group only the following is possible on vehicles up to 31.5.09 with code (386) Preinstallation for telephone "Cell phone", UPCI [UHI] system:

Accepting a call waiting call and simultaneously ending all existing calls 

If the user is conducting a call or two calls using the toggling function, when another incoming call is received it is displayed in the multifunction display and in the COMAND display or SPLITVIEW display.

If the user decides to answer the incoming call, the existing calls are ended.

SMS 

SMS messages are imported by the COMAND controller unit when the mobile phone is connected to the COMAND controller unit.

In the COMAND controller unit, the messages received are placed into different lists.

Up to 31.5.09:

The mobile phone receives an SMS message and transmits it via the UPCI [UHI] (Universal Portable Cell Phone Interface) cell phone holder over a direct line to the UPCI [UHI] (Universal Portable Cell Phone Interface) control unit. The UPCI [UHI] (Universal Portable Cell Phone Interface) control unit receives the SMS message and transmits it to the COMAND controller unit via MOST.

As of 1.6.09

The mobile phone receives an SMS message and transmits it via the Bluetooth module (A34/7) over a Bluetooth connection to the Bluetooth antenna (A2/91). The Bluetooth antenna transmits the SMS message via a direct line to the COMAND controller unit.

On receiving a new SMS message, an acoustic signal is output by the COMAND controller unit and a symbol is displayed in the COMAND display or SPLITVIEW display.

Up to 31.5.09 without code (494) USA version, the user can also compose SMS messages and send them via the mobile phone: The parameters for sending SMS messages (such as the service provider no., memory time) are supplied by the COMAND controller unit itself. If there are no parameters stored, then the parameters of the mobile phone are used.

With code (494) USA version, the user is only able to receive SMS messages.

Only those SMS messages that were received while the mobile phone was in the UPCI [UHI] (Universal Portable Cell Phone Interface) cell phone holder are loaded onto the UPCI [UHI] (Universal Portable Cell Phone Interface) control unit and displayed in the COMAND display.

As of 1.6.09 (with code (386) Comfort telephone): It is only possible to compose an SMS message using the mobile phone.

"Voice mail" (with code (494) USA version) 

If absent when a call is received, a "voice mail" will be sent by the provider. The receipt of a voice mail is signaled by a symbol at the top right of the COMAND display.

Communication via rear handset (with code (856) 2nd handset in rear armrest) 

With the rear handset it is possible to operate a mobile phone that is authorized at the COMAND controller unit.

The rear handset makes the following functions possible:

scientia non olet · About LEMON Manuals