Phone call acceptance, function - GF82.70-P-2009CW
MODEL 204.0/2 with CODE (523) MB Audio 20 radio Basic telephony
MODEL 204.0/2 with CODE (510) Audio 20 with CD changer Basic telephony
MODEL 204.0/2 with CODE (525) MB Audio 50 APS radio Basic telephony
MODEL 204.0/2 with CODE (511) Audio 50 APS with DVD changer Basic telephony
MODEL 204.0/2 with CODE (527) COMAND APS with single DVD drive (with navigation) Basic telephony
MODEL 204.0/2 with CODE (512) COMAND APS with DVD changer Basic telephony
MODEL 204.0 with CODE (494) USA version Basic telephony
MODEL 204.0/2 with CODE (386) Mobile phone Comfort telephony
MODEL 204.0 with CODE (389) Mobile phone preinstallation with universal interface, USA/Canada Comfort telephony
Function requirements
- Status "circuit 30 ON" or "circuit 15R ON"
- Enabled Subscriber Identification Module (SIM) card inserted in mobile phone
- Mobile phone and "master control unit" switched on
- Correct Personal Identification Number (PIN) entered, if set on the mobile phone
- Mobile phone system operating error-free
- One mobile telephone network is available in sufficient strength and quality
- Compatible mobile phone inserted into the mobile phone cradle (A34/15) (comfort telephony) or Bluetooth mobile phone in the vehicle and registered with the "master control unit" (basic telephony)
Depending on equipment installed, one of the following control units is installed:
- COMAND controller unit, (A40/3), with code (527) COMAND APS with single DVD drive (with navigation)
- COMAND controller unit, with code (512) COMAND APS with DVD changer
- Radio with auto pilot system (A2/56), with code (525) MB Audio 50 APS radio
- Radio with auto pilot system, with code (511) Audio 50 APS with DVD changer
- Radio (A2), with code (523) MB Audio 20 radio
- Radio, with code (510) Audio 20 with CD changer
- Radio, with code (494) USA version (model 204.0)
The function description uses the term "master control unit".
Operating instruction
A call is accepted and rejected via:
- Buttons on the mobile phone
- Telephone buttons on the "master control unit"
- Audio/COMAND control panel (A40/9)
- Left multifunction steering wheel button group (S110) and right multifunction steering wheel button group (S111)
- Voice control system (VCS [SBS]), with code (511) Audio 50 APS with DVD changer, with code (527) COMAND APS with single DVD drive (with navigation) or with code (512) COMAND APS with DVD changer
Function sequence for call signal with comfort telephony and with code (810) Sound system
The mobile phone receives a call signal in the following way:
- Multifunction antenna (A28/11) and discrete line, with code (386) Mobile phone
- Multifunction antenna, discrete line and frequency switchover control unit (N96) (with code (359) TELE AID emergency call system) with code (389) Mobile phone preinstallation with universal interface, USA/Canada (model 204.0)
- Cradle
Information about the caller is displayed on the mobile phone's screen. The display on the mobile phone's screen is forwarded internally.
At the same time, the call signal is forwarded to the "master control unit" in the following way:
- Cradle
- Bluetooth antenna (integrated into the Bluetooth contact plate of the cradle)
- Bluetooth antenna (A2/91)
- Discrete line
The "master control unit" transmits the call tone via the Media Oriented System Transport (MOST) to the sound system amplifier control unit (N40/3). From there, the call tone is transmitted via discrete lines to the following speakers:
- Left front door speaker (H4/1)
- Right front door speaker (H4/2)
- Left rear door speaker (H4/3)
- Right rear door speaker (H4/4)
- Center instrument panel speaker (H4/27)
- Bass speaker (H4/29)
- Left rear surround speaker (H4/54)
- Right rear surround speaker (H4/57)
At the same time, the "master control unit" mutes the currently active audio source (e.g. in radio mode) (MUTE). This takes place internally in the "master control unit".
The caller ID is displayed on the Audio/COMAND display (A40/8) by the "master control unit" via a low voltage differential signaling (LVDS) line.
In addition, the caller ID is displayed in the instrument cluster (A1) (except Entry-Line) via the interior CAN.
In vehicles except code (810) Sound system, the call tone is output directly from the "master control unit" via discrete lines to the following speakers:
- Left front door speaker
- Right front door speaker
- Left rear door speaker
- Right rear door speaker
- Center instrument panel speaker
With basic telephony, the mobile phone receives the call signal via the mobile phone antenna. The call signal is then forwarded to the "master control unit" in the following way:
- Mobile phone antenna
- Bluetooth antenna
- Discrete line
Accept call function sequence over mobile phone buttons
Pressing the "Accept call" button on the mobile phone serves to accept the call in handsfree mode. The control signals from the buttons on the mobile phone are processed internally.
Function sequence for accepting a call via telephone buttons on the "master control unit"
The call is accepted in handsfree mode by pressing the "Accept phone call" button on the "master control unit". The control signals from the buttons on the "master control unit" are processed internally.
Accept call function sequence over Audio/COMAND control panel
The caller ID is displayed on the Audio/COMAND display by the "master control unit" via an LVDS line by the call signal.
Selecting the "Accept call" function using the Audio/COMAND control panel serves to accept the call in handsfree mode. The control signals from the Audio/COMAND control panel are forwarded to the "master control unit" via the telematics CAN.
Accept call function sequence over multifunction steering wheel button groups
The call is accepted in handsfree mode by pressing the accept/ terminate phone call button (S111s3) in the corresponding panel. The control signal from the accept/terminate phone call button is forwarded to the "master control unit" via the following components:
- Steering LIN
- Steering column module control unit (N80)
- Chassis CAN
- Instrument cluster
- Interior CAN
Function sequence for accepting a call via VCS [SBS], with code (511) Audio 50 APS with DVD changer, with code (527) COMAND APS with single DVD drive (with navigation) or with code (512) COMAND APS with DVD changer and with code (810) Sound system
Pressing the voice control system ON button (S111s4) of the right multifunction steering wheel button group activates the voice control of the voice control system. The control signal from the VCS [SBS] on button is forwarded to the "master control unit" via the following components:
- Steering LIN
- Steering column module control unit
- Chassis CAN
- Instrument cluster
- Interior CAN
A signal tone is emitted after the voice control system has been activated.
The signal tone is transmitted from the "master control unit" via MOST to the sound system amplifier control unit.
From there, the signal tone is transmitted via discrete lines to the following speakers:
- Left front door speaker
- Right front door speaker
- Left rear door speaker
- Right rear door speaker
- Center instrument panel speaker
- Bass speaker
- Left rear surround speaker
- Right rear surround speaker
The call is only accepted with the corresponding voice command. The voice commands are acquired by the voice control system microphone (B25/7) and forwarded via a discrete line directly to the "master control unit".
The individual voice commands are listed in the "Linguatronic operator's manual".
In vehicles except code (810) Sound system, the signal tone is transmitted directly from the "master control unit" via discrete lines to the following speakers:
- Left front door speaker
- Right front door speaker
- Left rear door speaker
- Right rear door speaker
- Center instrument panel speaker
Function sequence for phone call in handsfree mode with comfort telephony and with code (810) Sound system
After the call has been accepted, the "master control unit" receives or transmits the mobile phone signals or data in the following way:
- Discrete line and multifunction antenna, with code (386) Mobile phone
- Discrete line, frequency switchover control unit (with code (359) TELE AID emergency call system) and multifunction antenna, with code (389) Mobile phone preinstallation with universal interface, USA/Canada
- Cradle
- Bluetooth antenna (integrated into the Bluetooth contact plate of the cradle)
- Bluetooth antenna
- Discrete line
The voice input in handsfree mode (except "private mode") is acquired by the VCS [SBS] microphone and forwarded via a discrete line directly to the "master control unit".
The voice output (except "private mode") takes place from the "master control unit" via MOST to the sound system amplifier control unit. From there, the voice output is transmitted via discrete lines to the following speakers:
- Left front door speaker
- Right front door speaker
- Left rear door speaker
- Right rear door speaker
- Center instrument panel speaker
- Bass speaker
- Left rear surround speaker
- Right rear surround speaker
In vehicles except code (810) Sound system, the voice output takes place directly from the "master control unit" via discrete lines to the following speakers:
- Left front door speaker
- Right front door speaker
- Left rear door speaker
- Right rear door speaker
- Center instrument panel speaker
For basic telephony, the "master control unit" receives or transmits the mobile phone signals or data in the following way:
- Mobile phone antenna
- Bluetooth antenna
- Discrete line
In general, the telephone connection is established in handsfree mode for basic telephony and for comfort telephony after accepting the call.
With comfort telephony, if the mobile phone is taken out of the cradle after establishing the phone connection in handsfree mode and thus disconnected from the "master control unit", the phone call is conducted in "private mode". With comfort telephony, if the mobile phone is inserted into the cradle again during an ongoing phone call, the phone call is conducted again in handsfree mode.
Reject call function sequence over mobile phone buttons
Pressing the "End" button on the mobile phone rejects the call. The control signals from the buttons on the mobile phone are processed internally.
Function sequence for rejecting a call via telephone buttons on the "master control unit"
The call is rejected by pressing the "End" button on the "master control unit". The control signals from the telephone buttons on the "master control unit" are processed internally.
Reject call function sequence over Audio/COMAND control panel
The caller ID is displayed on the Audio/COMAND display by the "master control unit" via an LVDS line by the call signal.
By selecting the "Reject" function the call is then rejected. The control signals from the Audio/COMAND control panel are forwarded to the "master control unit" via the telematics CAN.
Reject call function sequence over multifunction steering wheel button groups
Pressing the accept/terminate phone call button in the corresponding subfield rejects the call. The control signal from the accept/terminate phone call button is forwarded to the "master control unit" via the following components:
- Steering LIN
- Steering column module control unit
- Chassis CAN
- Instrument cluster
- Interior CAN
| Electrical function diagram for mobile phone, establishing a call, ending, accepting | With code (386) Mobile phone With code (512) COMAND APS with DVD changer with CODE (810) Sound system Comfort telephony |
PE82.70-P-2053-99FAA | |
| With code (389) Mobile phone preinstallation with universal interface, USA/Canada With code (512) COMAND APS with DVD changer with CODE (810) Sound system Comfort telephony Model 204.0 with code (359) TELE AID emergency call system |
PE82.70-P-2053-99FAB | ||
| Front central operating unit, component description | A40/9 | GF54.21-P-4500CW | |
| Cockpit central display, component description | A40/8 with code (523) MB Audio 20 radio with CODE (494) USA version With code (510) Audio 20 with CD changer with CODE (525) MB Audio 50 APS radio With code (511) Audio 50 APS with DVD changer Entry |
GF54.30-P-6100CW | |
| A40/8 With code (527) COMAND APS with Single DVD disk drive (with navigation) With code (512) COMAND APS with DVD changer High |
GF54.30-P-6100CWH | ||
| Radio control panel component description | A2 with code (523) MB Audio 20 radio |
GF82.60-P-3116CW | |
| A2 with CODE (494) USA version |
GF82.60-P-3116CWA | ||
| A2 With code (510) Audio 20 with CD changer |
GF82.60-P-3116CWB | ||
| Radio/navigation unit, component description | A2/56 with CODE (525) MB Audio 50 APS radio |
GF82.61-P-4111CW | |
| A2/56 With code (511) Audio 50 APS with DVD changer |
GF82.61-P-4111CWA | ||
| Audio tuner control unit, component description | N40/3 with CODE (810) Sound system |
GF82.62-P-3132CWS | |
| Telephone and GPS roof antenna component description | A28/11 With code (386) Mobile phone With code (389) Mobile phone preinstallation with universal interface, USA/Canada |
GF82.62-P-4119CW | |
| Bluetooth antenna component description | A2/91 | GF82.62-P-4201CW | |
| Frequency switchover control unit, component description | N96 Model 204.0 With code (359) TELE AID emergency call system With code (389) Mobile phone preinstallation with universal interface, USA/Canada |
GF82.62-P-4204CWU | |
| Speaker system, component description | H4/1, H4/2, H4/3, H4/4, H4/27 Except code (810) Sound system | GF82.62-P-4220CW | |
| H4/1, H4/2, H4/3, H4/4, H4/27, H4/29, H4/54, H4/57 with CODE (810) Sound system | GF82.62-P-4220CWS | ||
| Handsfree system microphone, component description | B25/7 | GF82.70-P-4121CW | |
| Mobile phone bracket, component description | A34/15 With code (386) Mobile phone With code (389) Mobile phone preinstallation with universal interface, USA/Canada |
GF82.70-P-5300CW | |
| COMAND controller unit, component description | A40/3 With code (527) COMAND APS with Single DVD disk drive (with navigation) |
GF82.85-P-3136CW | |
| A40/3 With code (512) COMAND APS with DVD changer |
GF82.85-P-3136CWA |