Remove/install radius rod - AR35.20-P-0111V
MODEL 171.442 /454 /456 /473
Shown on model 171.442
MODIFICATION NOTES
| Self-locking bolt, rear axle carrier rear rubber mount to frame floor | *BA35.10-P-1002-01A |
| Self-locking nut, strut rod to rear axle carrier, M12 | *BA35.20-P-1001-03A |
| Self-locking nut, strut rod to wheel carrier, M12 | *BA35.20-P-1002-03A |
| Remove/install | |||
|---|---|---|---|
| Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between the columns of the lifting platform and position the four support plates at the lifting platform support points specified by the vehicle manufacturer. | - | |
| 1 | Raise vehicle with lifting platform | AR00.60-P-1000V | |
| 2 | Secure vehicle on lifting platform | ||
| 3 | Remove wheel. | ||
| Remove/install wheels, rotate if necessary | AP40.10-P-4050V | ||
| 4 | Detach thrust arm (5) from wheel carrier | *BA35.20-P-1003-05A | |
| 5 | Detach torque strut (3) from wheel carrier | *BA35.20-P-1002-03A | |
| Figure | |||
| 6 | Support rear axle carrier (4) and secure to prevent it from falling down | Telescoping transmission jack |
Figure |
| 7 | Loosen bolts (1) and lower rear axle carrier (4) | *BA35.10-P-1001-01A | |
| *BA35.10-P-1002-01A | |||
| 8 | Detach torque strut (3) from rear axle carrier (4) | *BA35.20-P-1001-03A | |
| Figure | |||
| 9 | Install in the reverse order | ||
| 10 | Perform a wheel alignment check | AR40.20-P-0200V |
REAR AXLE CARRIER
| Number | Designation | Model 171 | |||
|---|---|---|---|---|---|
| BA35.10-P-1001-01A | Self-locking bolt, front rear axle carrier rubber mount to frame floor | Nm | - | ||
| with bolt | Stage 1 | Nm | - | ||
| Flange Ø 24mm | Stage 2 | ∠° | - | ||
| with bolt | Stage 1 | Nm | 60 | ||
| flange Ø 26mm | Stage 2 | ∠° | 90 | ||
| BA35.10-P-1002-01A | Self-locking bolt, rear axle carrier rear rubber mount to frame floor | Nm | - | ||
| with bolt | Stage 1 | Nm | - | ||
| Flange Ø 24mm | Stage 2 | ∠° | - | ||
| with bolt | Stage 1 | Nm | 60 | ||
| flange Ø 26mm | Stage 2 | ∠° | 90 | ||
TORQUE STRUT
| Number | Designation | Model 171 | ||
|---|---|---|---|---|
| BA35.20-P-1001-03A | Self-locking nut, tension arm to rear axle carrier | M12 | Nm | 70 |
| M14 | Nm | - | ||
| BA35.20-P-1002-03A | Self-locking nut, torque strut to wheel carrier | M12 | Nm | 70 |
| M16 | Nm | - | ||
TORQUE STRUT
| Number | Designation | Model 171 | |
|---|---|---|---|
| BA35.20-P-1003-05A | Self-locking nut, thrust arm to wheel carrier | Nm | 50 |
| ∠° | 45 | ||