Retrofit iPod interface wiring harness - AZ82.60-P-0001-01TR

iPod interface wiring harness 

Fig 1: Identifying Ipod Interface Wiring Harness Connections

The iPod interface wiring harness (3) is routed by starting in the left of the luggage compartment into the left front footwell. The iPod interface wiring harness (3) is to be routed under the floor covering only. It must be routed and fastened such that any damage and vibration noise is prevented.

1. Unpin the brown/red line from the blue connector (28) of the iPod interface wiring harness (3).

   Blue plug (28) is still required.

   Routing diagram for iPod wiring harness 

   Fig 2: Routing Diagram For Ipod Wiring Harness

   
2. Detach connector housing (6) from audio gateway control unit (N93/1).
3. Detach plug (7) from connector housing (6).
4. Unpin brown (br) line from plug (7) of vehicle's wiring harness and insert brown (br) line of iPod interface wiring harness (3) into same contact cavity of plug (7).
5. Unpin brown/red line from plug (7) of vehicle's wiring harness and insert brown/red line (br/rt) of iPod interface wiring harness (3) into same contact cavity of plug (7).
   Fig 3: Detaching Connector Housing From Audio Gateway Control Unit

   
6. Join plug (7) and connector housing (6).
7. Join connector housing (6) to audio gateway control unit (N93/1).
8. Insert brown (br) and brown/red (br/rt) line of vehicle's wiring harness into any contact cavity of the blue plug (28) and strap down to given wiring harness.

   Insert brown (br)and brown/red (br/rt) line of vehicle's wiring harness into blue plug, to avoid any short circuiting.

   Don not connect the blue connector housing supplied but strap it down onto wiring harness.

9. Insert plug (27) of iPod interface wiring harness (3) into contact cavity 27 of the rear SAM control unit with fuse and relay module (N10/2).

   Plug position 27 is mechanically coded for the plug (27) of the iPod interface wiring harness (3).

10. Connect ground connection (9) of iPod interface wiring harness (3) to ground (left wheelhouse in luggage compartment) (W6).
11. Connect relay (24) contained in parts kit to socket C of the rear SAM control unit with fuse and relay module (N10/2).
12. Insert the 7.5 A fuse (25) included in the parts kit into plug position 5 of the rear SAM control unit with fuse and relay module (N10/2).
    Fig 4: Identifying Fuse, Relay And Fuse And Relay Module

    
13. Route the iPod interface wiring harness (3) as shown from the luggage compartment into the interior and fasten in place using felt strap.

    Shown on model 211.0 

    Fig 5: Identifying Ipod Interface Wiring Harness Route

    
14. Route iPod interface wiring harness (3) into the interior onto the left wheel arch as shown.
15. Route iPod interface wiring harness (3) under the floor covering forwards to the left footwell.
    Fig 6: Identifying Ipod Interface Wiring Harness Route Under Floor Covering

    
16. Route iPod interface wiring harness (3) as shown into the footwell and attach to given wiring harness.
17. Detach cockpit voltage distributor (CAN) connector (X30/6).
18. Join CAN plug (21) of iPod interface wiring harness (3) to free plug position of cockpit voltage distributor (CAN) connector (X30/6).

    Connect CAN plug (21) to any free plug position.

19. Connect cockpit voltage distributor (CAN) connector (X30/6).
20. Route branch-off line with plug for Command connection (20) of iPod interface wiring harness (3) as shown into the radio recess (see arrow).

    The plug(19)is connected at a later stage to the iPod (2)interface.

    Fig 7: Identifying Ipod Interface Wiring Harness Route Into Footwell

    
21. Detach plug (20) of vehicle's AUX cable to COMAND operating, display and controller unit (A40/3) and strap down wiring harness.

    The vehicle's AUX cable can no longer be used in combination with the iPod (1).

22. Connect plug (20) of iPod interface wiring harness (3) to the COMAND operating, display and controller unit (A40/3).
    Fig 8: Identifying Plug