Drain/fill in coolant - AR20.00-P-1142TMG
ENGINE 156.982 in MODELS 209.377 /477
ENGINE 156.983 in MODELS 211.077 /277, 219.377
Shown on model 211
| Drain | |||
| Risk of injury caused by fingers being pinched or crushed when removing, installing or aligning hoods, doors, trunk lids, tailgates or sliding roof. | Keep body parts and limbs well clear of moving parts. | AS00.00-Z-0011-01A | |
| Risk of death caused by vehicle slipping or toppling off the lifting platform | Align vehicle between columns of lifting platform and position four support plates at lifting platform support points specified by vehicle manufacturer. | AS00.00-Z-0010-01A | |
| Risk of injury to skin and eyes caused by scalding from contact with hot coolant spray. Risk of poisoning from swallowing coolant. | Do not open cooling system unless coolant temperature is below 90°C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers. Wear protective gloves, protective clothing and safety glasses. |
AS20.00-Z-0001-01A | |
| Risk of explosion caused by oxyhydrogen gas. Risk of poisoning and caustic burns caused by swallowing battery acid. Risk of injury caused by burns to skin and eyes from battery acid or when handling damaged lead-acid batteries | No fire, sparks, open flames or smoking. Wear acid-resistant gloves, clothing and safety glasses. Only pour battery acid into suitable and appropriately marked containers. |
AS54.10-Z-0001-01A | |
| 1 | Disconnect ground line from battery | ||
| Notes on battery | All models | AH54.10-P-0001-01A | |
| Model 209 | AR54.10-P-0003Q | ||
| Model 211.0 | AR54.10-P-0003T | ||
| Model 211.2 | AR54.10-P-0003TA | ||
| Model 219 | AR54.10-P-0003TX | ||
| 2 | Open engine hood | Model 209 | AR88.40-P-1000Q |
| Model 211 | AR88.40-P-1000T | ||
| Model 219 | AR88.40-P-1000TX | ||
| 3 | Open cap on coolant expansion reservoir | ||
| 4 | Raise vehicle with lifting platform | Model 209 | AR00.60-P-1000P |
| Model 211 | AR00.60-P-1000T | ||
| Model 219 | AR00.60-P-1000TX | ||
| 5 | Remove bottom engine compartment paneling | Model 209 | AR61.20-P-1105P |
| Model 211 | AR61.20-P-1105T | ||
| Model 219 | AR61.20-P-1105TX | ||
| Drain coolant from radiator | |||
| 6 | Slide collector siphon hose onto fitting at radiator | ||
| 7 | Open siphon hose (1) at radiator and drain coolant. | Observe regulations for disposal of coolant. |
|
| Drain coolant at crankcase | |||
| 8 | Release right crankcase drain plug (2) and left crankcase drain plug (3) | ||
| 9 | Push drain hose onto crankcase drain screws | ||
| 10 | Loosen crankcase drain screws further by hand; drain coolant | Observe regulations for disposal of coolant. |
|
| Filling | |||
| 11 | Tighten drain plug (1) at radiator and detach siphon hose from fitting | ||
| 12 | Detach drain hose from crankcase drain screw | ||
| 13 | Tighten right crankcase drain plug (2) and left crankcase drain plug (3) | *BA03.20-P-1009-01J | |
| 14 | Pour in coolant and bleed cooling system | AR20.00-P-1142-04A | |
| Notes on coolant | All engines | AH20.00-N-2080-01A | |
| Notes on coolant level | Model 209 | AH20.00-P-1142-01PI | |
| Notes on coolant level | Model 211, 219 | AH20.00-P-1142-01V | |
| Coolant specifications | Sheet 310.1 | BB00.40-P-0310-01A | |
| Anticorrosion/antifreeze agents (Sheet 325.0) | Sheet 325.0 | BB00.40-P-0325-00A | |
| *BF20.00-P-1001-02U | |||
| Figure | |||
| Figure | |||
| Figure | |||
| 15 | Inspect cooling system for leaks | AR20.00-P-1010TMG | |
| 16 | Install engine compartment paneling | Model 209 | AR61.20-P-1105P |
| Model 211 | AR61.20-P-1105T | ||
| Model 219 | AR61.20-P-1105TX | ||
| 17 | Lower vehicle | ||
| 18 | Screw cap on coolant expansion reservoir | ||
| 19 | Connect ground cable to battery | ||
| Model 209 | AR54.10-P-0003Q | ||
| Model 211.0 | AR54.10-P-0003T | ||
| Model 211.2 | AR54.10-P-0003TA | ||
| Model 219 | AR54.10-P-0003TX | ||
| 20 | Perform basic programming | ||
| Model 209 | AR00.19-P-0200Q | ||
| Model 211 | AR00.19-P-0200T | ||
| Model 219 | AR00.19-P-0200TX | ||
| 21 | Close engine hood | Model 209 | AR88.40-P-1000Q |
| Model 211 | AR88.40-P-1000T | ||
| Model 219 | AR88.40-P-1000TX |
CRANKSHAFT BEARING CAP
| Number | Designation | Engine 156 | |
|---|---|---|---|
| BA03.20-P-1009-01J | Drain screw for coolant | Nm | 15 |
COOLING SYSTEM
| Number | Designation | Engine 156 in models 209, 211, 219 | ||
|---|---|---|---|---|
| BF20.00-P-1001-02U | Cooling system | Total filling capacity | ≈ Liters | 8 |
| Antifreeze/water | Up to -37°C | 50/50 | ||
| Up to -45°C | 55/45 | |||
| Specifications for Operating Fluids | Sheet | BB00.40-P-0310-01A | ||
| Sheet | BB00.40-P-0325-00A | |||