 |
Remove |
|
|
| 1 |
Remove door lining from front door. |
|
AR72.10-P-1000N |
| 2 |
Remove sidebag from front door |
|
AR91.60-P-0690M |
| 3 |
Disconnect left/right door speaker group connector (H4/1x1; H4/2x1) |
|
|
| 4 |
Unscrew bolts (7) and remove woofer speaker (H4/1h2; H4/2h2) |
 |
Figure |
| 5 |
Remove door foil from front door |
|
AR72.10-P-1010N |
| 6 |
Remove crank operated window on front door |
|
AR72.10-P-1900N |
| 7 |
Remove cap (11) above nut (12) from door floor panel (13) and unscrew nut (12) |
|
|
| 8 |
Loosen nut (8) and unhook rear window lift guide rail (10) from bracket (9) |
|
|
| 9 |
Lift rear window lift guide rail (10) until the stud bolts (10a) on the door floor panel (13) are unhooked and then lay rear window lift guide rail (10) down in door at front |
|
|
| 10 |
Unhook Bowden cable (6) from inside door opener from door lock (1) and remove |
Unclip bracket (5) from door lock (1) |
|
| 11 |
Fold open retainer (14) for release rod and unhook release rod (15) |
|
|
| 12 |
Disconnect CL line (3) |
|
|
| 13 |
Remove lock cylinder guide |
|
AR72.10-P-2400N |
| 14 |
Unscrew bolt on lock cover (4) |
|
|
| 15 |
Unscrew lock mounting bolts (2) |
|
Figure |
| 16 |
Take out door lock (1) through access cover |
|
|
 |
Install |
|
|
| 17 |
Insert door lock (1) through access cover |
|
|
| 18 |
Screw in lock mounting bolts (2) |
 |
*BA72.10-P-1008-01E |
| |
|
|
Figure |
| 19 |
Screw in lock cover bolt (4) |
|
|
| 20 |
Install lock cylinder guide |
|
AR72.10-P-2400N |
| 21 |
Connect CL line (3) |
|
|
| 22 |
Hook release rod (15) into retainer (14) |
With retainer (14) open, press release rod upward until resistance can be felt. Then close retainer (14) again and lock |
|
| 23 |
Hook Bowden cable (6) for inside door opener into door lock (1) |
Clip bracket (5) into door lock (1) |
|
| 24 |
Install rear window guide rail (10) on door floor panel (13) |
Hook stud (10a) into door floor panel. |
|
| 25 |
Hook rear window lift guide rail (10) into bracket (9) and screw in nut (8) |
Do not tighten nut (8) so that it is still possible to adjust the crank window. |
AR72.10-P-1950N |
| 26 |
Screw in nut (12) |
Do not tighten nut (12) so that it is still possible to adjust the crank window. |
|
| 27 |
Install crank window in front door |
|
AR72.10-P-1900N |
| 28 |
Insert cap (11) above nut (12) into door floor panel (13) |
|
|
| 29 |
Check clearance, correct if necessary |
|
*BE72.10-P-1001-01C |
| 30 |
Perform function check |
|
|
| 31 |
Install door foil on front door |
|
AR72.10-P-1010N |
| 32 |
Insert woofer speaker (H4/1h2; H4/2h2) and screw in bolt (7) |
|
|
| 33 |
Connect left, right door speaker group connector (H4/1x1; H4/2x1) |
|
|
| 34 |
Install sidebag in front door |
|
AR91.60-P-0690M |
| 35 |
Install door lining in front door |
|
AR72.10-P-1000N |