Remove/install seat belt (front seat) - AR91.40-P-1010M

MODELS 220.0 /1 up to 31.8.02

Fig 1: Identifying Seat Belt (Front Seat) Remove/Install Components - Models 220.0 /1 Up To 31.8.02 (1 Of 2)

Fig 2: Identifying Seat Belt (Front Seat) Remove/Install Components - Models 220.0 /1 Up To 31.8.02 (2 Of 2)

	Remove/install
	Risk of injury. Injury may result when the tension in the spring in the automatic belt retractor is released.	Never disassemble automatic belt retractors.	AS91.00-Z-0002-01A
	Risk of injury. Injuries may result when performing testing or repair work on airbag or emergency tensioning retractor units.	Store airbag unit with expulsion area on top, do not subject to temperatures above 100 °C. When working on these units, disconnect the power supply.	AS91.00-Z-0001-01A
	Instructions for performing repair, body work and welding on vehicles with airbags and ETR units	Models 203, 209, 211.004/ 006/ 016/ 061/065/ 070, 215, 220, 230, 240, 450.3/4. Model 463.244 /245 /247 /248 /249 /250 /254 /309 /322 /323 /332 /333.	AH91.00-P-0002-01M
	Evaluation of airbags and emergency tensioning retractors on accident vehicles	Models 129 as of 1.7.93, 163, 168, 170, 202 as of 1.7.93, 203, 208, 209, 210, 211.004/006/ 016/ 061/ 065/ 070, 215, 220, 230, 240, 414, 461, 463, 638, 901, 902, 903, 904,905. Models WD141, WD241, WD341, WD641, WD741, XD141, XD241, XD341, XD441, XD541, XD641, XD741, YD141, YD241, YD341, YD441, YD541, YD641, YD741.	AH91.00-P-0006-01B
	Legal regulations on handling and storing airbags and emergency tensioning retractors	Models 124, 129, 140, 163, 168, 170, 202, 203, 208, 209, 210, 211.004/ 006/ 016/ 061/065/ 070, 215, 220, 230, 240, 314, 316, 318, 414, 450.3/4, 461, 463, 638, 668, 670, 690.6, 901, 902, 903, 904, 905, 950, 952, 953, 954, 970, 972, 974, 975, 976. Models WD141, WD241, WD341, WD641, WD741, XD141, XD241, XD341, XD441, XD541, XD641, XD741, YD141, YD241, YD341, YD441, YD541, YD641, YD741.	AH91.00-P-0004-01A
1	Move front seat as far forward as possible with backrest upright
2.1	Switch ignition off, withdraw ignition key
2.2	Switch engine off, remove transmitter key from vehicle	With keyless go code 889. Keep transmitter key outside transmission range.
3	Remove paneling on B-pillar		AR68.30-P-4700M
4	Remove cover on belt end fitting (1) and undo screw	Torque wrench.	Figure
		Belt end fitting screw.	*BA91.40-P-1001-01A
5	Unscrew nut (5) from seat belt guide bracket (2)	Torque wrench.	Figure
		Nut on front seat belt guide bracket	*BA91.40-P-1002-01A
6	Release coupling on driver ETR [GUS] ignition squib (R12/1), passenger-side ETR [GUS] ignition squib (R12/2) and coupling (6)
7	Remove screw (4) at automatic seat belt retractor (3)	Torque wrench.	Figure
		Screw on front automatic belt retractor.	*BA91.40-P-1004-01A
8	Remove automatic belt reel (3)	Installation: Note different version (left/right) of seat belt emergency tensioning retractor and correct seating in catch. Noises from the automatic belt reel when rolling up belt are normal. The only available response to negative customer feedback regarding unacceptable noise levels is to replace the seat belt assembly with emergency tensioning retractor in its entirety. On no account should oil or grease be used to help eliminate noise. Automatic belt retractors that have been opened are no longer under warranty! If the seat belt with emergency tensioning retractor has been replaced, the defective unit must be disposed of properly: ↓
	Notes on disposal of airbags and emergency tensioning retractors		OS91.00-P-0001-01A
	Make ETR units unusable		AR91.40-P-0611A
9	Install in the reverse order
10	Carry out diagnosis	STAR DIAGNOSIS

SEAT BELTS/EMERGENCY TENSIONING RETRACTORS

Number	Designation		Model 220
BA91.40-P-1001-01A	Belt end fitting screw	NM	30
BA91.40-P-1002-01A	Screw/nut on front seat belt guide bracket	NM	30
BA91.40-P-1004-01A	Screw on front automatic belt reel	NM	30

Fig 3: Identifying Torque Wrench (001 589 66 21 00)