Remove/install wheels, rotate if necessary - AP40.10-P-4050Z

MODEL 124, 129, 140, 164, 168, 170, 202, 203, 208, 209, 210, 211, 215, 220, 230, 240 

MODEL 414 

Fig 1: Identifying Wheels Nuts Tightening Sequence - Model 124, 129, 140, 164, 168, 170, 202, 203, 208, 209, 210, 211, 215, 220, 230, 240, 414

Courtesy of MERCEDES-BENZ USA

	Removing
	Risk of death  caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between the columns of the lifting platform and position the four support plates at the lifting platform support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
1	Raise vehicle with vehicle lift
2.1	Pull off wheel covers	Only vehicles with wheel covers.
3	Unscrew wheel bolts and remove wheels	All except Model 209, 230.474 /476 /479, 240: ↓
		Socket Model 209, 230.474 /476 /479, 240: ↓	Fig 2
		Socket wrench	Fig 3
	Wheel bolts modified	Model 210	BT40.10-P-0001-01A
	Check
4	Check wheel bolts	The round contact shoulders on the lug bolts must be free of oil and grease. Bolts with damaged threads, worn zinc plating on the radius seat or corroded radius seat must be replaced, otherwise they may shear off.
5	Check tires for damage and condition, and measure depth of tread		AP40.10-P-4051Z
	Information on tires / rims		AH40.10-P-9411-01A
	Notes on measuring tire tread depth	All models	AH40.10-P-0006-01T
		Brake pad gauge	Fig 4
6	Check disk wheels	Check for: Contamination to ensure that radius seats are free of oil and grease Damage to centering, radius seats and rim flanges corrosion on contact surfaces
7	Check wheel hub, wheel bolt thread and brake disk bowl on wheel contact surface for dirt and corrosion	Clean corroded surfaces with a wire brush or emery cloth. Dirty or corroded wheel bolt threads must be cleaned or recut. Any dirt or corrosion left in the thread prevents the wheel bolt from reaching the necessary preload force, despite the nominal torque having been reached. If the wheel bolt threads are damaged, the wheel hub must be replaced.
	Install
8.1	Rotate road wheels if necessary, maintaining the correct running direction	Except vehicles with mixed tires on the front and rear axle Depending on the state of wear after a distance between 5000 and 10, 000 km.
9	Slide on the road wheels and tighten the lug bolts.	Observe tightening sequence (1 to 5) All except model 164 and model 210 with special protection version, code 979: ↓
		Wheel bolt Model 210 with CODE 979, special protection version: ↓	*BA40.10-P-1001-01A
		Wheel bolt Model 164: ↓	*BA40.10-P-1001-01B
		Wheel bolt All except Model 209, 230.474 /476 /479, 240: ↓	*BA40.10-P-1001-01J
		Socket wrench bit Model 209, 230.474 /476 /479, 240: ↓	Fig 2
		Socket wrench	Fig 3
	Wheel bolts modified	Model 210	BT40.10-P-0001-01A
10	Lower vehicle
11	Rectify tire pressure on all wheels	If there is a loss of tire pressure: determine cause and replace the tire if necessary. On vehicles with tire pressure monitor: Only use plastic valve caps (risk of corrosion).
12.1	Fit wheel covers	Only vehicles with wheel covers.
13.1	Correct tire pressure of spare tire	Only vehicles with spare tire. In the event of tire pressure loss: Determine cause and replace tire of spare wheel if necessary. On vehicles with tire pressure monitor: Only use plastic valve caps (risk of corrosion).
13.2	Check expiry date of TIREFIT tire sealant	Only vehicles which are equipped with TIREFIT tire sealant.	AP40.10-P-4054R
	TIREFIT tire sealant	Model 163, 164, 168, 169, 170, 171, 199, 203, 209, 211, 215, 219, 230, 240, 414, 639	AH40.10-P-0001-01A
14.1	Activate the tire pressure monitoring system	On vehicles with tire pressure monitor, as far as possible: Only when replacing a wheel, changing tires or altering the tire pressure, refer to: ↓
	Perform adjustments to the control system	Model 164	AR54.30-P-1000-02GZA
		Model 211	AR54.30-P-1000-02RAT
		Model 230.467 /474 /475 /476 /479	AR54.30-P-1000-02RAR
		Model 240	AR54.30-P-1000-02RAH
	Tire pressure monitor (TPM) activation	Model 210.074 /274	GF40.15-P-0001-02A
		Model 215, 220 up to 30.9.00	GF40.15-P-0001-02B
		Model 215, 220 as of 01.10.00 up to 31.05.01	GF40.15-P-0001-02C
		Model 215, 220 as of 01.06.01 up to 31.08.02	GF40.15-P-0001-02D
		Model 215, 220 as of 01.09.02 up to 30.9.03 with tire pressure monitor	GF40.15-P-0001-02E

Fig 2: Identifying Wrench Socket (126 589 04 09 00)

Courtesy of MERCEDES-BENZ USA

Fig 3: Identifying Socket Wrench (230 589 01 09 00)

Courtesy of MERCEDES-BENZ USA

Fig 4: Identifying Brake Pad Gage (211 589 06 23 00)

Courtesy of MERCEDES-BENZ USA