Remove/install hinge lever with remote trunk closing - AR88.50-P-5125N
MODEL 215, 220 with CODE (881b) Remote trunk closing (RTC)
Shown on model 220
Fig 1: Identifying Remove/Install Components For Hinge Lever With Remote Trunk Closing - Shown On Model 220 (1 Of 2)
Fig 2: Identifying Remove/Install Components For Hinge Lever With Remote Trunk Closing - Shown On Model 220 (1 Of 2)
| Remove/Install | |||
| 1 | Open trunk lid | ||
| 2 | Remove coverings in trunk | Models 215.3, 463.244 /245 /247 /248 /249 /250 /254 /309 /322 /323 /332 /333. |
AR68.30-P-4600M |
| Model 220.8 |
AR68.30-P-4600MP | ||
| 3 | Remove trunk lid | AR88.50-P-5000M | |
| 4 | Unclip left and right gas-operated strut (2) | ||
| 5 | Unscrew bolts (3) and left hinge lever (4) | ||
| 6 | Unhook hydraulic cylinder (9) from lever (10) | ||
| 7 | Unscrew nuts (6) and right hinge lever (5) | ||
| 8 | Unclip stop protection caps (7) | ||
| 9.1 | Unscrew stop (8) | ||
| 10 | Install in the reverse order | ||
| 11 | Check for trunk lid fit in relation to rear fenders | ||
| Gap dimensions on hoods, doors and lids If fit is not precise: ↓ |
*BE60.00-P-1003-01A | ||
| Adjust trunk lid | AR88.50-P-5200M | ||
| 12 | Repair bolts (3) and nuts (6) with paint in visible area |
TEST AND ADJUSTMENT VALUES, GAP DIMENSIONS AT HOODS, DOORS AND COVERS
| Number | Designation | Model 215 | Model 220.0/1 | |||
|---|---|---|---|---|---|---|
| BE60.00-P-1003-01A | Gap dimension | Trunk lid to top of rear fender | Dimension "F" | mm | 4.0 (± 0.5) | 4.0 (± 0.5) |
| Trunk lid to bottom of rear fender | Dimension "M" | mm | - | - | ||
| Trunk lid to rear fender | Dimension "F" | mm | 4.0 (± 0.5) | 4.0 (± 1.5) | ||
| Trunk lid to taillamp | Dimension "M" | mm | 4.0 (± 0.5) | 4.4 (± 0.5) | ||
| Trunk lid to bumper | Dimension "V" | mm | - | - | ||
| Rear fender to taillamp | Dimension "U" | mm | - | - | ||
| Fig., see | AR60.00-P-0700-01N | AR60.00-P-0700-01M | ||||
TEST AND ADJUSTMENT VALUES, GAP DIMENSIONS AT HOODS, DOORS AND COVERS
| Number | Designation | Model 220.875/878 | |||
|---|---|---|---|---|---|
| BE60.00-P-1003-01A | Gap dimension | Trunk lid to top of rear fender | Dimension "F" | mm | 4.0 (± 0.5) |
| Trunk lid to bottom of rear fender | Dimension "M" | mm | - | ||
| Trunk lid to rear fender | Dimension "F" | mm | 4.0 (±0.5) | ||
| Trunk lid to taillamp | Dimension "M" | mm | 4.4 (± 0.5) | ||
| Trunk lid to bumper | Dimension "V" | mm | - | ||
| Rear fender to taillamp | Dimension "U" | mm | - | ||
| Fig., see | AR60.00-P-0700-01M | ||||