Install new stabilizer bar pivot bushing - AR32.20-P-0310M: Notes

MODEL 211 (except 211.08 /09 /28 /29) in the spring control arm 

MODEL 220 (except 220.08 /18) except CODE (487) Active Body Control (ABC) in spring control arm 

MODEL 230 except CODE (487) Active Body Control (ABC) in spring control arm 

Illustrated on model 220 

Fig 1: Installing Stabilizer Bar Pivot Bushing (Model 220)

	Remove/install
	Risk of death caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer.	AS00.00-Z-0010-01A
	Notes on self-locking nuts and bolts		AH00.00-N-0001-01A
	When working on the front-end assembly, be careful not to scratch, mark or notch the surfaces of aluminum parts. Otherwise the service life of the parts will be affected
Installation	Tighten nuts and bolts of chassis components only when vehicle is in ready-to-drive condition
1	Remove front wheel
	Remove/install wheels		AP40.10-P-4050Z
2	Detach torque strut (18) from steering knuckle (5)	Model 220 except 220.8, 230	AR33.15-P-0160-01I
		Type 220.8 Installation:  Replace self-locking nut. Check rubber boot on ball head of torque strut (18) for damage. If rubber boot is damaged, install new torque strut (18): ↓ Remove/install torque strut:	AR33.15-P-0160-01MB
		Model 220 except 220.8	AR33.15-P-0160I
		Type 220.8	AR33.15-P-0160MP
		Model 230	AR33.15-P-0160R
3	Remove track rod (10) from steering knuckle (5).	Installation:  Replace self-locking nut.	AR46.40-P-0200-02I
4	Undo nut (23b)	To do so, counterhold bolt (23d) with shortened Allen wrench (shop-made). Turn steering if necessary. Installation:  Tighten nut (23b) only when vehicle is in ready-to-drive condition.
		Model 211	*BA32.20-P-1002-02B
		Model 220, 230	*BA32.20-P-1002-02H
6	Unscrew nut (23c), detach link rod (23) from spring control arm (17) and swing vertically upward	Installation:  Press link rod (23) onto hexagon of stabilizer bar pivot bushing (8) on spring control arm (17).
		On model 211 up to chassis number 1A 762000, in addition both link rods (23) must be replaced.	AR32.35-P-3328T
		Model 211	*BA32.20-P-1006-02B
		Model 220, 230	*BA32.20-P-1001-02H
7	Remove rubber boot (9) and wire fasteners of torsion bar pivot bushing (8)	When pressing out the ball joint with rubber boot assembled the special tool will be damaged due to the press-out force which is too high.
8	Press stabilizer bar pivot bushing (8) out of spring control arm (17)		AR32.20-P-0310-01M
	Checking
9	Check rubber boot (19) of ball joint in spring control arm (17) for damage	Model 220 except 220.8, 230 If rubber boot (19) is damaged, install new spring control arm (17): ↓ Remove/install, spring control arm at front axle:
		Model 220 except 220.8	AR33.15-P-0170I
		Type 220.8	AR33.15-P-0170MP
		Model 230	AR33.15-P-0170R
10	Check rubber mount of spring control arm (17) for damage	Model 220 except 220.8, 230 Replace rubber mount if necessary: ↓ Replace rubber mount of spring control arm:
		Model 220 except 220.8, 230 Type 220.8	AR33.15-P-0170-02I
11	Install in the reverse order

FRONT AXLE STABILIZER BAR

FRONT AXLE STABILIZER BAR