Check oil pressure - AR18.00-P-1250DA

ENGINE 112 in MODEL 170, 202, 203, 208.365 /465, 209.361 /365 /461 /465, 210, 211.080 /280 /082 /282, 220, 230.467 

ENGINE 113 in MODEL 211.083 /283, 220, 230.474 /475 

ENGINE 113.981 in MODEL 163.174 

ENGINE 113.968 in MODEL 209.375 /475 

ENGINE 112.913 in MODEL 211.061 /261 

ENGINE 112.949 in MODEL 211.065 /265 

ENGINE 113.967 in MODEL 211.070 /270 

ENGINE 113.987 in MODEL 209.376 /476 

Fig 1: Identifying Oil Pressure Gauge Components - Shown On Engine 112

	Remove/install
	Risk of death caused by vehicle slipping or toppling off the lifting platform.	Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer.	AS00.00-Z-0010-01A
1	Unclip cover on front side of engine	Model 211, 220, 230.475
2.1	Remove engine cover with integrated air filter	Except model 170.466, 203.065 /265, 230.474, 220.074/174 The air filter is integrated in the engine cover. Remove engine cover or air filter by pulling it vertically up and off the cylinder head covers.
2.2	Remove air filter housing	Model 170.466, 203.065 /265, 230.474, 220.074 /174	AR09.10-P-1150SVK
3.1	Remove fan shroud (9) together with electric fan	Model 220, 230.474 /475 /467	AR20.40-P-6800AB
3.2	Remove electric fan	On model 163: Unscrew bolts at bottom of fan shroud (9).
		Engine 113.981 in model 163.174	AR20.40-P-5000GH
		Engine 112.947 in model 170.465	AR20.40-P-5000SV
		Engine 112.960 in model 170.466
		Engine 112.912 in Model 203.061 /261, 209.361 /461 with transmission 716.6, 722.6 Engine 112.946 in model 203.064 /264 /764 with transmission 722.6 Engine 112.961 in model 203.065 /265 with transmission 722.6 Engine 113.968 in model 209.375 /475 with transmission 722.6 Engine 113.987 in model 209.376 /476 with transmission 722.636 Engine 112.955 in model 209.365/ 465 with transmission 722.618 Engine 112.916 in Model 203.081 /281 Engine 112.953 in model 203.084 /284	AR20.40-P-5000PV
4	Remove screw plug (4) together with seal (5) at timing case	Installation:  Install new seal in order to avoid oil loss.	*BA18.40-P-1001-01B
5	Connect oil-pressure manometer (1) to connecting pipe (2) on timing case		Fig 2
			Figure
	Checking
6	Check engine oil level		Fig 5
7	Connect remote thermometer (6)	Insert temperature sensor through dipstick guide tube into engine oil.
			Fig 3
	Risk of accident  caused by vehicle starting off by itself when engine is running. Risk of injury  caused by contusions and burns during starting procedure or when working near the engine as it is running	Secure vehicle to prevent it from moving by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts.	AS00.00-Z-0005-01A
8	Start engine, measure oil pressure	Bring engine up to operating temperature (approx. 80°C). When the throttle is opened, the oil pressure must rise without any delay.	*BE18.00-P-1001-01B
9	Install in the reverse order

OIL LEVEL/OIL PRESSURE SENSOR

OIL LEVEL/OIL PRESSURE SENSOR

OIL LEVEL/OIL PRESSURE SENSOR

Fig 2: Identifying Testing Unit (103 589 00 21 00)

Fig 3: Identifying Remote Thermometer (124 589 07 21 00)

Fig 4: Identifying Double Union (166 589 00 63 00) )

Fig 5: Identifying Dipstick (120 589 07 21 00)