Sliding / pop-up roof - BE77.20-P-1000-01A
Models 163, 168, 202, 203, 208, 209.3, 210, 211, 215, 220, 414
MODIFICATION NOTES
| 18.1.01 | Value changed from 0 (+1.5) mm to 1 (± 1) mm | Value changed in row 1004 on model 203.7 | |
| 18.1.01 | Value changed from 0 (+1.5) mm to 1 (± 1) mm | Figure modified n series 1005 for models 203.7 | |
| 18.1.01 | Value of 2.5 (± 0.5) mm changed to 2 (± 1) mm Value of 2 (+0.5) mm changed to 2 (± 1) mm Value of 9.5 (± 0.5) mm changed to 9 (± 1) mm Value of 7.5 (± 0,5) mm changed to 7 (± 1) mm |
Figure modified n series 1007 for models 203.7 | |
| 18.1.01 | Value changed from 14 mm to 14 (-1) mm | Figure modified n series 1008 for models 203.7 |
TEST AND ADJUSTMENT VALUES FOR TILTING/SLIDING ROOF
| Number | Designation | Model Series 163 | Model 168 | Model 202 | ||
|---|---|---|---|---|---|---|
| BE77.20-P-1001-01A | Gap dimensions | Sliding/pop-up roof cover, front | mm | - | - | 0.15 |
| Sliding/pop-up roof cover, on side and rear | mm | - | - | 0,30 | ||
| BE77.20-P-1002-01A | Height setting | Measuring position "A" (x) | mm | 140 | 80 | 140 |
| front: lower than outer skin of the roof | mm | 0...1 | 0...2 | 0...1 | ||
| rear: higher than outer roof surface | mm | 0...1 | 0...2 | 0...1 | ||
| BE77.20-P-1003-01A | Gap dimensions | Lamella to lamella, position "C" | mm | - | 3...4 | - |
| Lamellas to roof cutout, position "B" | mm | - | 4...5 | - | ||
| BE77.20-P-1004-01A | Height adjustment wind deflector to tilting/sliding roof | Wind deflector higher than tilting/sliding roof | mm | - | - | - |
| BE77.20-P-1005-01A | Height adjustment tilting/sliding roof to glass roof, rear | Sliding/pop-up roof higher than glass roof, rear | mm | - | - | - |
| BE77.20-P-1006-01A | Height adjustment glass roof, rear to rear window | Glass roof, rear, higher than rear window | mm | - | - | - |
| BE77.20-P-1007-01A | Gap dimensions | Wind deflector to tilting/sliding roof | mm | - | - | - |
| Sliding/pop-up roof to glass roof, rear | mm | - | - | - | ||
| Glass roof, rear, to rear window | mm | - | - | - | ||
| Windshield to outer mounting clamp of trim strip | mm | - | - | - | ||
| BE77.20-P-1008-01A | Gap dimensions | Mounting clips water deflector to glass roof outer edge | mm | - | - | - |
| BE77.20-P-1009-01A | Gap dimensions | Rear glass roof to rear window | mm | - | - | - |
| BE77.20-P-1010-01A | Rear glass roof height adjustment to rear window | Rear glass roof higher than rear window | mm | - | - | - |
TEST AND ADJUSTMENT VALUES FOR TILTING/SLIDING ROOF
| Number | Designation | Model 203.0 | Model 203.2 | Model 203.7 | ||
|---|---|---|---|---|---|---|
| BE77.20-P-1001-01A | Gap dimensions | Sliding/pop-up roof cover, front | mm | 0.15 | 0,15 | - |
| Sliding/pop-up roof cover, on side and rear | mm | 0,30 | 0,30 | - | ||
| BE77.20-P-1002-01A | Height setting | Measuring position "A" (x) | mm | 140 | 140 | - |
| front: lower than outer skin of the roof | mm | 0...1 | 0...1 | - | ||
| rear: higher than outer roof surface | mm | 0...1 | 0...1 | - | ||
| BE77.20-P-1003-01A | Gap dimensions | Lamella to lamella, position "C" | mm | - | - | - |
| Lamellas to roof cutout, position "B" | mm | - | - | - | ||
| BE77.20-P-1004-01A | Height adjustment wind deflector to tilting/sliding roof | Wind deflector higher than tilting/sliding roof | mm | - | - | 1 (± 1) |
| BE77.20-P-1005-01A | Height adjustment tilting/sliding roof to glass roof, rear | Sliding/pop-up roof higher than glass roof, rear | mm | - | - | 1 (± 1) |
| BE77.20-P-1006-01A | Height adjustment glass roof, rear to rear window | Glass roof, rear, higher than rear window | mm | - | - | 0 (+2) |
| BE77.20-P-1007-01A | Gap dimensions | Wind deflector to tilting/sliding roof | mm | - | - | 2 (± 1) |
| Sliding/pop-up roof to glass roof, rear | mm | - | - | 2 (± 1) | ||
| Glass roof, rear, to rear window | mm | - | - | 9 (± 1) | ||
| Windshield to outer mounting clamp of trim strip | mm | - | - | 7 (± 1) | ||
| BE77.20-P-1008-01A | Gap dimensions | Mounting clips water deflector to glass roof outer edge | mm | - | - | 14(-1) |
| BE77.20-P-1009-01A | Gap dimensions | Rear glass roof to rear window | mm | - | - | - |
| BE77.20-P-1010-01A | Rear glass roof height adjustment to rear window | Rear glass roof higher than rear window | mm | - | - | - |
TEST AND ADJUSTMENT VALUES FOR TILTING/SLIDING ROOF
| Number | Designation | Models 208.3 | Model 209.3 | Model 210 | ||
|---|---|---|---|---|---|---|
| BE77.20-P-1001-01A | Gap dimensions | Sliding/pop-up roof cover, front | mm | 0,15 | 0,15 | 0,15 |
| Sliding/pop-up roof cover, on side and rear | mm | 0,30 | 0,30 | 0,30 | ||
| BE77.20-P-1002-01A | Height setting | Measuring position "A" (x) | mm | 140 | 140 | 140 |
| front: lower than outer skin of the roof | mm | 0...1 | 0...1 | 0...1 | ||
| rear: higher than outer roof surface | mm | 0...1 | 0...1 | 0...1 | ||
| BE77.20-P-1003-01A | Gap dimensions | Lamella to lamella, position "C" | mm | - | - | - |
| Lamellas to roof cutout, position "B" | mm | - | - | - | ||
| BE77.20-P-1004-01A | Height adjustment wind deflector to tilting/sliding roof | Wind deflector higher than tilting/sliding roof | mm | - | - | - |
| BE77.20-P-1005-01A | Height adjustment tilting/sliding roof to glass roof, rear | Sliding/pop-up roof higher than glass roof, rear | mm | - | - | - |
| BE77.20-P-1006-01A | Height adjustment glass roof, rear to rear window | Glass roof, rear, higher than rear window | mm | - | - | - |
| BE77.20-P-1007-01A | Gap dimensions | Wind deflector to tilting/sliding roof | mm | - | - | - |
| Sliding/pop-up roof to glass roof, rear | mm | - | - | - | ||
| Glass roof, rear, to rear window | mm | - | - | - | ||
| Windshield to outer mounting clamp of trim strip | mm | - | - | - | ||
| BE77.20-P-1008-01A | Gap dimensions | Mounting clips water deflector to glass roof outer edge | mm | - | - | - |
| BE77.20-P-1009-01A | Gap dimensions | Rear glass roof to rear window | mm | - | - | - |
| BE77.20-P-1010-01A | Rear glass roof height adjustment to rear window | Rear glass roof higher than rear window | mm | - | - | - |
TEST AND ADJUSTMENT VALUES FOR TILTING/SLIDING ROOF
| Number | Designation | Model 211 | Model 215 | Model 220 | ||
|---|---|---|---|---|---|---|
| BE77.20-P-1001-01A | Gap dimensions | Sliding/pop-up roof cover, front | mm | 0,15 | 0,15 | 0,15 |
| Sliding/pop-up roof cover, on side and rear | mm | 0,30 | 0,30 | 0,30 | ||
| BE77.20-P-1002-01A | Height setting | Measuring position "A" (x) | mm | 140 | 140 | 140 |
| front: lower than outer skin of the roof | mm | 0...1 | 0...1 | 0...1 | ||
| rear: higher than outer roof surface | mm | 0...1 | 0...1 | 0...1 | ||
| BE77.20-P-1003-01A | Gap dimensions | Lamella to lamella, position "C" | mm | - | - | - |
| Lamellas to roof cutout, position "B" | mm | - | - | - | ||
| BE77.20-P-1004-01A | Height adjustment wind deflector to tilting/sliding roof | Wind deflector higher than tilting/sliding roof | mm | 1 (± 1) | - | - |
| BE77.20-P-1005-01A | Height adjustment tilting/sliding roof to glass roof, rear | Sliding/pop-up roof higher than glass roof, rear | mm | 1 (± 1) | - | - |
| BE77.20-P-1006-01A | Height adjustment glass roof, rear to rear window | Glass roof, rear, higher than rear window | mm | - | - | - |
| BE77.20-P-1007-01A | Gap dimensions | Wind deflector to tilting/sliding roof | mm | 1 (± 1) | - | - |
| Sliding/pop-up roof to glass roof, rear | mm | - | - | - | ||
| Glass roof, rear, to rear window | mm | - | - | - | ||
| Windshield to outer mounting clamp of trim strip | mm | - | - | - | ||
| BE77.20-P-1008-01A | Gap dimensions | Mounting clips water deflector to glass roof outer edge | mm | - | - | - |
| BE77.20-P-1009-01A | Gap dimensions | Rear glass roof to rear window | mm | 5 (± 1) | - | - |
| BE77.20-P-1010-01A | Rear glass roof height adjustment to rear window | Rear glass roof higher than rear window | mm | 5 (± 0,5) | - | - |
TEST AND ADJUSTMENT VALUES FOR TILTING/SLIDING ROOF
| Number | Designation | Model 240 | Model 414 | ||
|---|---|---|---|---|---|
| BE77.20-P-1001-01A | Gap dimensions | Sliding/pop-up roof cover, front | mm | 0,15 | 3,08 |
| Sliding/pop-up roof cover, on side and rear | mm | 0,30 | 3,26 | ||
| BE77.20-P-1002-01A | Height setting | Measuring position "A" (x) | mm | 140 | - |
| front: lower than outer skin of the roof | mm | 0...1 | 0...1 | ||
| rear: higher than outer roof surface | mm | 0...1 | 0...1 | ||
| BE77.20-P-1003-01A | Gap dimensions | Lamella to lamella, position "C" | mm | - | - |
| Lamellas to roof cutout, position "B" | mm | - | - | ||
| BE77.20-P-1004-01A | Height adjustment wind deflector to tilting/sliding roof | Wind deflector higher than tilting/sliding roof | mm | - | - |
| BE77.20-P-1005-01A | Height adjustment tilting/sliding roof to glass roof, rear | Sliding/pop-up roof higher than glass roof, rear | mm | - | - |
| BE77.20-P-1006-01A | Height adjustment glass roof, rear to rear window | Glass roof, rear, higher than rear window | mm | - | - |
| BE77.20-P-1007-01A | Gap dimensions | Wind deflector to tilting/sliding roof | mm | - | - |
| Sliding/pop-up roof to glass roof, rear | mm | - | - | ||
| Glass roof, rear, to rear window | mm | - | - | ||
| Windshield to outer mounting clamp of trim strip | mm | - | - | ||
| BE77.20-P-1008-01A | Gap dimensions | Mounting clips water deflector to glass roof outer edge | mm | - | - |
| BE77.20-P-1009-01A | Gap dimensions | Rear glass roof to rear window | mm | - | - |
| BE77.20-P-1010-01A | Rear glass roof height adjustment to rear window | Rear glass roof higher than rear window | mm | - | - |