Remove/install spring control arm and replacement of rubber mount - AR35.20-P-0114I: Notes

MODEL 220.025 /026 /028 /083 /084 /087 /125 /126 /128 /183 /184 /187

MODEL 220.063 /065 /067 /070 /075 /163 /165 /167 /170 /175 except CODE (487) Active Body Control (ABC)

Fig 1: Identifying Spring Control Arm Remove/Install Components

MODIFICATION NOTES

20.7.00	Figure divided	Value in BA35.20-P-1001-01A revised for Model 215	*BA35.20-P-1001-01A
20.7.00	Figure divided	Value changed to BA35.20-P-1001-01A for model 220	*BA35.20-P-1001-01A

	Remove/Install
	Risk of death caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between the columns of the lifting platform and position the four support plates at the lifting platform support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
	Notes on self-locking nuts and bolts		AH00.00-N-0001-01A
	While working on the rear axle care must be taken to ensure that the surface of all aluminum components do not get any scratches, cracks and notches. Otherwise the service life of the parts will be affected
1	Raise vehicle with lifting platform
2	Remove exhaust system as of flange connection	See ↓ Remove exhaust system complete:
		Engine 112, 113	AR49.10-P-7000AA
		Engine 613	AR49.10-P-7000M
		Engine 628	AR49.10-P-7000MB
		Engine 648	AR49.10-P-7000MZ
3	Detach cover (6g) from spring control arm (6)	To do this, pull pin out of expansion rivet and remove expansion rivet from cover and spring control arm.
4	Remove spring control arm (6) from rear axle carrier	Screwdriver bit	*119589001000
		Installation: The rear axle shaft must be horizontal when tightening the nut.
		Installation: Tighten bolts or nuts as per tightening angle.	AR35.10-P-0010-08IA
			*BA35.20-P-1001-01A
5	Remove spring control arm (6) from wheel carrier	Installation: The rear axle shaft must be horizontal when tightening the nut.
			*BA35.20-P-1002-01A
6	Remove suspension strut (6j) from spring control arm (6)		*BA32.25-P-1005-04B
	Check
7	Check rubber bushing (6b) of spring control arm (6) in rear axle carrier	If necessary after check: ↓
		Remove/install spring control arm rubber bushing	AR35.20-P-0114-01I
		Extraction and insertion tool	Figure
		Press	Figure
8	Install in the reverse order

STRUTS

Number	Designation		Model 220.025/026/028/063/065/067/070/073/074/075/125/126/128/163/165/167/170/173/174/175/176/178/179/	Model 220.083/084/087/183/184/187
BA32.25-P-1005-04B	Nut, rear strut to track control arm	Nm	110	110

SPRING LINK

Number	Designation			Model 220
BA35.20-P-1001-01A	Self-locking nut, track control arm to rear subframe	1st stage	Nm	50
BA35.20-P-1001-01A	Self-locking nut, track control arm to rear subframe	2nd stage	∠°	90
BA35.20-P-1002-01A	Self-locking nut, spring link to wheel carrier.	1st stage	Nm	120
BA35.20-P-1002-01A	Self-locking nut, spring link to wheel carrier.	2nd stage	∠°	-

Fig 2: Identifying Screwdriver Bit (119 589 00 10 00)

Fig 3: Identifying Removal And Installation Tool (220 589 01 43 00)

Fig 4: Identifying Press (202 589 04 43 10)