Specified automatic transmission fluids (commercial vehicle, van) - overview - BB00.40-P-0231-02A

	Sheet 231.2
For Allison transmissions, it is absolutely essential to observe the application instructions under point 3.4!	BB00.40-P-0231-00A

NOTE: For commercial vehicle axle applications in the service fill area 235.6 can be used equivalently to 235.0.

COMMERCIAL VEHICLES, VANS, SHEETS 235.0 UP TO 235.9

Major assembly

SAE grade

Sheet No.

235.0

235.1

235.4

235.5

235.6

235.7

235.8

235.9

Hypoid axle except rear axle 746.2
HL6 and HO6 up to 2005

75W-90
80W-90
85 W-90, 90

◦

•

Hypoid axle in model 636, 639

85W-90

•

Hypoid axle HL6 and HO6 as of 2005
Rear axle 746.211/216/217
Rear axle 746.210 as of M 140 394 except in model 374
Rear axle 746.213 as of M 138 407 except in model 374

75W-90
80W-90
85 W-90, 90

•

Spur gear axle
ZF transfer case
Fuller transmission

80, 80 W
80 W/85 W
(Hot zones SAE 90, 85 W-90)

•

Model 901, 903, 904, 905 with rear axle 741.13/407/408/409

•

Model 905 with rear axle 741.98

•

Model 906 with rear axle 741.412/413/414/415/416/417/418/419/420

•

Planetary axle

85 W-90, 90

◦

•

MB transfer case 7)

80W

•

Transfer case

80 W/85 W

◦

•

MB transfer case

80 W/85
W75W-90

•

MB manual transmission

G 1/15, 1/17, 1/18 ⁽¹⁾
G 2/24, 2/27
G 3/36, 3/49
G 3/50 ⁽¹⁾
G 3/60 ⁽¹⁾, 3/61
G 3/70

80, 80 W ⁽¹⁾
80 W/85 W ⁽¹⁾

•⁽¹⁾

G 1/D 14
G 3/45-6, 3/55-6, 3/65, 3/90
G 4/65-6, 4/95-6, 4/95-7, 4/110-6
G 65-7 G 100/125/135
155/180/200
GO 3/60, GO 3/80
GO 4/95/105/120/130
GTO 24-5 GV
4/65-6, 4/95-6, 4/110-6

30, 40 80, 80 W 80 W/85 W
(Hot zones SAE 90, 85 W-90)

•

GO 170/190/210/230/240

75W-90

•

GO 240

75W-90

•

G 60, G56, G 85, GO110

75W/90W

•

G60, G56, G85, GO110 in tropical countries

G100, G131-9, G210, G211, G 240, G260, G131, G221, G230, G231, G280

80W

•⁽²⁾

7circlef;⁽²⁾

Constant-mesh transmission G 281 (BM 715.370), G 330 (BM 715.380) without oil cooler

Constant-mesh transmission G 281 (BM 715.370), G 330 (BM 715.380) with oil cooler

•

Constant-mesh transmission G 211-12 (BM 715.350) with and without oil cooler

ZF manual transmission

80, 80 W 85 W 75 W/85 W
(Hot zones SAE 90, 85 W-90)

•

•⁽³⁾

•

AG 4
- automatic part

- final-drive assembly

•

This table only serves as an overview!
•Should be used.
◦Can be used.

⁽¹⁾	Only for: G 1/18-5, G 3/50, G 3/60 without MS synchronization

⁽²⁾	Transmissions with oil coolers only.

⁽³⁾	With intarder

COMMERCIAL VEHICLES, VANS, SHEETS 235.10 UP TO 235.29

Major assembly

SAE grade

Sheet No.

235.10

235.11

235.12

235.13

235.20

235.27

235.28

235.29

Hypoid axle except rear axle 746.2
HL6 and HO6 up to 2005

75W-90
80W-90
85 W-90, 90

•

Hypoid axle in model 636, 639

85W-90

•

Hypoid axle HL6 and HO6 as of 2005
Rear axle 746.211/216/217
Rear axle 746.210 as of M 140 394 except in model 374
Rear axle 746.213 as of M 138 407 except in model 374

75W-90
80W-90
85 W-90, 90

•

Hypoid axle,
Rear axle 746.210 as of M 140 394 in model 374
Rear axle 746.213 as of M 138 407 in model 374

75W-90
80W-90
85 W-90, 90

•

Model 906 with rear axle 741.412/413/414/415/416/417/418/419/420

•

Planetary axle

85 W-90, 90

•

Transfer case

80 W/85 W

•

MB transfer case

80 W/85
W75W-90

•

MB manual transmission

G 1/15, 1/17, 1/18 ⁽¹⁾
G 2/24, 2/27
G 3/36, 3/40 G 3/50 ⁽¹⁾
G 3/60 ⁽¹⁾, 3/61
G 3/70

80, 80 W ⁽¹⁾
80 W/85 W ⁽¹⁾

•⁽¹⁾

G 1/D 14 G 3/45-6, 3/55-6, 3/65, 3/90 G 4/65-6, 4/95-6, 4/95-7, 4/110-6 G 65-7 G 100/125/135 155/180/200 GO 3/60, GO 3/80 GO 4/95/105/120/130 GTO 24-5 GV 4/65-6, 4/95-6, 4/110-6

30, 40 80, 80 W 80 W/85 W (Hot zones SAE 90, 85 W-90)

•

•⁽²⁾

GO 160

75W-90

•

GO 170/190/210/230/240

75W-90

•

G 16/28/20/32/33

75W/8

•

G 60, G56, G 85, GO110

75W/90W

•⁽²⁾

•

G60, G56, G85, GO110 in tropical countries

•

G100, G131-9, G 210, G 211, G 240, G260, G131, G221, G230, G231, G280

80W

•

Transmission 715.68

•

Constant-mesh transmission G 281 (BM 715.370), G 330 (BM 715.380) without oil cooler

•

Constant-mesh transmission G 281 (BM 715.370), G 330 (BM 715.380) with oil cooler

•

Constant-mesh transmission G 211-12 (BM 715.350) with and without oil cooler

•

ZF manual transmission

80, 80 W 85 W 75 W/85 W (Hot zones SAE 90, 85 W-90)

•

ZF manual transmission with ZF torque converter clutch 400
MB transmission G240 with ZF torque converter clutch 400

•

Voith retarder for commercial vehicle

•

Voith retarder for bus*

•

Sprintshift transmission

75W/85W

•

This table only serves as an overview!
•Should be used.
◦Can be used.

⁽¹⁾	Only for: G 1/18-5, G 3/50, G 3/60 without MS synchronization

⁽²⁾	Use engine oils as under Sheet 235.12, SAE 30 for common oil circuits with ZF torque converter clutch 400

*MILEAGE FOR VOITH RETARDER WITHOUT MAINTENANCE INTERVALS

Field of applicationmoderate climate
	235.27 (A oils)	235.28 (B oils)	235.29 (C oils)
Heavy duty	90, 000 km	120, 000 km	180, 000 km
Light duty	120, 000 km	180, 000 km	300, 000 km

Field of application: hot climate
Heavy duty	60, 000 km	90, 000 km	120, 000 km
Light duty	90, 000 km	120, 000 km	180, 000 km

COMMERCIAL VEHICLES, VANS, SHEETS 236.1 UP TO 236.91

Major assembly

SAE grade

Sheet No.

236.1

236.2

236.3

236.6

236.7

236.8

236.9

236.11

236.12

236.14

236.81

236.91

Mechanical steering

ATF

•

MB manual transmission⁽²⁾
G 1/15, 1/17, 1/18
G 2/24, 2/27
G 3/36, 3/40
G 3/50
G 3/60, 3/61
G 3/70

ATF

•

MB power steering

ATF

•

ZF power steering

ATF

•

Hydraulic fan drive for auxiliary radiator

ATF

•

Hydrostatic fan drive

ATF

•

MB automatic transmission, except 722.6/9

ATF

•

Automatic transmission 722.6

ATF

•

Automatic transmission 722.9

ATF

•

MB automatic transmission W 4 B 035 ⁽¹⁾

ATF

•

Voith/ZF automatic transmission

ATF

•

Allison transmission ⁽²⁾

ATF

•

•⁽³⁾

Voith turbo clutch (VIAB)

ATF

•

ZF 4 HP 20

ATF

•

AG 4
- automatic part

•

- final-drive assembly

Hydraulic lowering system in model 905.613

•

This table only serves as an overview!
•Should be used.
◦Can be used.

⁽¹⁾	Only install W 4 B 035 as of major assembly end no 00 57 33 or modified shift plate. ATF as per Sheets 236.1, 236.8, and 236.81 may not be used in W 4 B 035.

⁽²⁾	For Allison transmissions, the application instructions on sheet 231.0 must be observed!

⁽³⁾	Automatic transmission fluids (ATF), Sheet 236.91 or TES 295 for Allison automatic transmission. This oil permits much longer oil change intervals, in particular for Allison transmissions.

When changing to a different oil:

Change service life factors in the maintenance system (WS) and pay attention to specified maintenance intervals.