LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2004 >> CL55 >> Repair and Diagnosis >> Body & Frame >> Mirrors >> Detachable Body Components - 215 & 220 Chassis >> Testing & Repair >> Remove/install rear bumper - AR88.20-P-2200 >> Remove/install rear bumper - AR88.20-P-2200N

Remove/install rear bumper - AR88.20-P-2200N

MODEL 215 with CODE (550) Trailer hitch except CODE (772) AMG styling package - front spoiler, side skirts and rear apron trailer hitch with removable ball neck 

MODEL 215 with CODE (550) Trailer hitch except CODE (772) AMG styling package - front spoiler, side skirts and rear apron mechanically pivoting trailer hitch 

Fig 1: Identifying Rear Bumper Remove/Install Components - Model 215 (1 Of 3)
G04850246
Fig 2: Identifying Rear Bumper Remove/Install Components - Model 215 (2 Of 3)
G04850247
Fig 3: Identifying Rear Bumper Remove/Install Components - Model 215 (3 Of 3)
G04850248
REMOVING Remove     
1 Remove trunk lining Model 215.3.
IMPORTANT Rear wall paneling can remain in vehicle.
AR68.30-P-4600M
2.1 Disconnect emergency call system (TELEAID) replacement antenna connector (X23/17) IMPORTANT Only on TELE AID emergency call system (D2B) (code 347) or with TELE AID (code 855).  
3.1 Disconnect PTS connector, rear bumper (X35/28) IMPORTANT Only on Parktronic system (PTS) (code 220a).  
4 Unscrew bolts (5). IMPORTANT On left and right.  
5 Push fender liner (7) to the side and unscrew bolts (6) IMPORTANT On left and right.  
6 Unscrew nut (14) IMPORTANT On left and right.  
7 Remove covers (15) and loosen nuts (9) 2 to 3 turns IMPORTANT On left and right.  
8 Remove bumper (1)    
9 Unscrew bolts (3) and remove bumper bracket (2) from bumper (1)    
INSTALLING Install     
10 Fit bumper bracket (2) in bumper (1) and screw in bolts (3) TORQUE SPECIFICATION Bolt, bumper to bumper reinforcement *BA31.11-P-1004-01A 
11 Install bumper (1), slide mount (1a) on left and right into guides (8)    
12 Adjust bumper (1) in longitudinal direction IMPORTANT Slide bumper (1) onto collar bolts (10) until edge of bumper (13) is flush with edge of rear fender  
13 Adjust height of bumper (1) IMPORTANT The height of the bumper can be adjusted by turning the collar bolt (10)  
14 Tighten nuts (9) and install covers (15) IMPORTANT On left and right.  
    TORQUE SPECIFICATION Nut, bumper reinforcement to trailer hitch. *BA31.11-P-1005-01A 
15 Screw on nut (14) IMPORTANT On left and right.  
16 Screw in bolts (5) IMPORTANT On left and right.  
17 Screw in bolts (6) and install fender liner (7) IMPORTANT On left and right.  
18.1 Connect rear bumper PTS connector (X35/28) IMPORTANT Only on Parktronic system (PTS) (code 220a).  
19.1 Connect emergency call system (TELEAID) replacement antenna connector (X23/17) IMPORTANT Only on TELE AID emergency call system (D2B) (code 347) or with TELE AID (code 855).  
20 Install trunk linings Model 215.3. AR68.30-P-4600M
TORQUE SPECIFICATION TRAILER HITCH MECHANICAL SYSTEM

Number Designation Model 215
BA31.11-P-1004-01A Bolt, bumper to bumper reinforcement Nm 8
BA31.11-P-1005-01A Nut, bumper reinforcement to trailer hitch Nm 8