Check wiper arms and adjust - AR82.30-P-6000T: Notes

MODELS 211, 215, 220, 230, 240 

Shown on model 211, wiper system in reverse position 

Fig 1: Checking Wiper System In Reverse Position

	Check
	Risk of injury in the form of trapping or crushing, or even severing of limbs, if caught in windshield wiper mechanism	Always remove ignition key when working on windshield wiper mechanism.	AS82.30-Z-0001-01A
	When working on raised driver-side wiper arm (1) or front passenger side wiper arm (2) it has to be observed that they do not fall onto the windshield to prevent it from being damaged.
1	Move wiper system from parked position	To do this, turn on ignition (circuit 15 or circuit 15R) and turn wiper switch to position "Two". After the wiper system has left the parked position, turn off ignition and turn back wiper switch to position "Zero".
2	Manually position wiper system into reverse position	Distance between driver-side wiper blade and A-pillar (A): Models 211, 215, 220, 230 approx. 50 mm, Model 240 approx. 70 mm Distance between front passenger side wiper blade and A-pillar (B): for model 211 approx. 350 mm, for models 215, 220, 230, 240, the distance between the front passenger side wiper blade and the A-pillar (B) results from the distance between the driver-side wiper blade to the A-pillar (A). For left-hand drive vehicles, measured from the upper wiper blade end of the driver-side wiper blade (1) and the front passenger side wiper blade (2) to the inside of the left A-pillar. For right-hand drive vehicles, measured from the upper wiper blade end of the driver-side wiper blade (1) and the front passenger side wiper blade (2) to the inside of the right A-pillar.
3	Remove wiper blades	See Operating Instructions
4	Measure angle of incidence of driver-side wiper blade (1) and front passenger side wiper blade (2) to windshield and record	When changing from reverse position to parked position it has to be observed that the driver-side wiper arm (1) and the front passenger side wiper arm (2) do not have any direct contact to the windshield to prevent it from being scratched. Cover driver-side wiper arm (1) and front passenger side wiper arm (2) with appropriate means.	AR82.30-P-6000-01T
			Figure
5	Compare test values with adjustment values and select correct adjustment measure	The specified adjustment values are only valid for left-hand drive vehicles. For right-hand drive vehicles, the particular sign has to be changed.
		Angle of incidence of wiper arm on driver-side (1) in reverse position	*BE82.30-P-1001-01E
		Angle of incidence of wiper arm on front passenger side (2) in reverse position	*BE82.30-P-1002-01E
		Angle of incidence of wiper arm on driver-side (1) in parked position	*BE82.30-P-1003-01E
		Angle of incidence of wiper arm on front-passenger side (2) in parked position	*BE82.30-P-1004-01E
	Notes on wiper arm adjustment		AH82.30-P-0001-01A
6.1	Adjust angle of incidence of driver-side wiper arm (1) or front passenger side wiper arm (2) in parked position	In the event that the test values deviate from the tolerance range in reverse position or in parked position and reverse position: Distort driver-side wiper arm (1) or front passenger side wiper arm (2) by at least the value of the tolerance deviation in reverse position. The specified adjustment values are only valid for left-hand drive vehicles. For right-hand drive vehicles, the particular sign has to be changed.	AR82.30-P-6100-01T
		Angle of incidence of wiper arm on driver-side (1) in parked position	*BE82.30-P-1003-01E
		Angle of incidence of wiper arm on front-passenger side (2) in parked position	*BE82.30-P-1004-01E
			Figure
6.2	Adjusting wiper system	In the event that the test values of the driver-side wiper arm (1) and front passenger side wiper arm (2) deviate from the tolerance range in parked position. The specified adjustment values are only valid for left-hand drive vehicles. For right-hand drive vehicles, the particular sign has to be changed.
		Model 211	AR82.30-P-6400-01T
		Angle of incidence of wiper arm on driver-side (1) in parked position	*BE82.30-P-1003-01E
			*BA82.30-P-1007-01A
			Figure
			Fig 3
			Figure
		Model 215, 220	AR82.30-P-6400-01M
		Angle of incidence of wiper arm on driver-side (1) in parked position	*BE82.30-P-1003-01E
			*BA82.30-P-1005-01A
			Figure
		Model 230	AR82.30-P-6400-01R
		Angle of incidence of wiper arm on driver-side (1) in parked position	*BE82.30-P-1003-01E
			*BA82.30-P-1005-01A
			Figure
		Model 240	AR82.30-P-6400-01H
		Angle of incidence of wiper arm on driver-side (1) in parked position	*BE82.30-P-1003-01E
			*BA82.30-P-1007-01A
			Figure
			Figure
7	Cover the wiper arm on the driver-side (1) and wiper arm on the front passenger side (2) using suitable aids and move the wiper system out of the parked position	When moving the wiper system out of the parked position, make sure that the driver-side wiper arm (1) and the front passenger side wiper arm (2) do not have any direct contact to the windshield to prevent it from being scratched. To do this, turn on ignition (circuit 15 or circuit 15R) and turn wiper switch to position "Two". After the wiper system has left the parked position, turn off ignition and turn back wiper switch to position "Zero".
8	Install wiper blades	See Operating Instructions
9	Perform wiper system function check

WINDSHIELD WIPER

WINDSHIELD WIPER

Fig 2: Identifying Mounting Wedge (110 589 03 59 00)

Fig 3: Identifying Pulling Hook (140 589 02 33 00)

Fig 4: Identifying Adjustment Tool Set (211 589 02 21 00)