ME fuel injection and ignition system (ME), DTC memory - AD07.61-P-4000L
ENGINE 137.970
| Risk of death caused by contact with parts conducting high voltages. | Do not touch parts which conduct high voltages. Persons who wear electronic implants (e.g. heart pacemakers) must not perform any work on the ignition system. | AS15.10-Z-0001-01A | |
| Risk of fatal injury when touching parts conducting high voltage when the ignition is switched off | After ignition is turned OFF, only disconnect the plug on the ECI power pack after first waiting for 3 minutes. The voltage in the condenser dissipates in this time. |
AS15.15-Z-0001-01A | |
| Notes on avoiding damage to ignition system | Engine 137 | AH15.10-P-0002-01L | |
| All checks on the electrical system gasoline injection system ME engine 137 are described in STAR DIAGNOSIS. The following list contains the fault code description for the corresponding fault code | |||
| Fault code STAR DIAGNOSIS ( |
Possible cause | Note | Fault code description |
| P2004 (P0100) | Hot-film mass-air sensor ME - fault code description | AD07.61-P-4000-01L | |
| P2007 (P0105) | Pressure sensor ME - fault code description | AD07.61-P-4000-02L | |
| P2006 (P0110) | Intake air temperature sensor ME - fault code description | AD07.61-P-4000-03L | |
| P2005 (P0115) | Coolant temperature sensor ME - fault code description | AD07.61-P-4000-04L | |
| P202D (P0125) | Coolant temperature sensor ME - fault code description | AD07.61-P-4000-04LA | |
| P200F (P0130) | O2 sensor signal - fault code description ME | Right O2 sensor upstream of TWC for cylinders 1 to 3 | AD07.61-P-4000-06L |
| P2010 (P0136) | O2 sensor signal - fault code description ME | Right O2 sensor downstream of TWC for cylinders 1 to 3 | AD07.61-P-4000-06L |
| P2082 (P0130) | O2 sensor signal - fault code description ME | Right O2 sensor upstream of TWC for cylinders 4 to 6 | AD07.61-P-4000-06L |
| P2083 (P0136) | O2 sensor signal - fault code description ME | Right O2 sensor downstream of TWC for cylinders 4 to 6 | AD07.61-P-4000-06L |
| P20A9 (P0150) | O2 sensor signal - fault code description ME | Left O2 sensor upstream of TWC for cylinders 7 to 9 | AD07.61-P-4000-06L |
| P20Aa (P0150) | O2 sensor signal - fault code description ME | Left O2 sensor upstream of TWC for cylinders 10 to 12 | AD07.61-P-4000-06L |
| P20Ab (P0156) | O2 sensor signal - fault code description ME | Left O2 sensor downstream of TWC for cylinders 7 to 9 | AD07.61-P-4000-06L |
| P20AC (P0156) | O2 sensor signal - fault code description ME | Left O2 sensor downstream of TWC for cylinders 10 to 12, | AD07.61-P-4000-06L |
| P200E (-) | O2 sensor signal - fault code description ME | Right O2 downstream of TWC for cylinders 1 to 3, sensor condition change | AD07.61-P-4000-06LA |
| P2081 (-) | O2 sensor signal - fault code description ME | Right O2 downstream of TWC for cylinders 4 to 6, sensor condition change | AD07.61-P-4000-06LA |
| P20C6 (-) | O2 sensor signal - fault code description ME | Right O2 downstream of TWC for cylinders 7 to 9, sensor condition change | AD07.61-P-4000-06LA |
| P20C7 (-) | O2 sensor signal - fault code description ME | Right O2 downstream of TWC for cylinders 10 to 12, sensor condition change | AD07.61-P-4000-06LA |
| P207F (-) | Aging of O2 sensor upstream of TWC - fault code description ME | Right O2 sensor upstream of TWC for cylinders 4 to 6, correction parameter limit exceeded | AD07.61-P-4000-07L |
| P20A5 (-) | Aging of O2 sensor upstream of TWC - fault code description ME | Left O2 sensor upstream of TWC for cylinders 7 to 9, correction parameter limit exceeded | AD07.61-P-4000-07L |
| P20A6 (-) | Aging of O2 sensor upstream of TWC - fault code description ME | Left O2 sensor upstream of TWC for cylinders 10 to 12, correction parameter limit exceeded | AD07.61-P-4000-07L |
| P200C (-) | Aging of O2 sensor upstream of TWC - fault code description ME | Right O2 sensor upstream of TWC for cylinders 1 to 3, correction parameter limit exceeded | AD07.61-P-4000-07L |
| P2080 (P0133) | Aging of O2 sensor upstream of TWC - fault code description ME | Right O2 sensor upstream of TWC for cylinders 4 to 6, cycle duration too long | AD07.61-P-4000-07LA |
| P20A7 (P0153) | Aging of O2 sensor upstream of TWC - fault code description ME | Left O2 sensor upstream of TWC for cylinders 7 to 9, Cycle duration too long | AD07.61-P-4000-07LA |
| P20A8 (P0153) | Aging of O2 sensor upstream of TWC - fault code description ME | Left O2 sensor upstream of TWC for cylinders 10 to 12, cycle duration too long | AD07.61-P-4000-07LA |
| P200D (P0133) | Aging of O2 sensor upstream of TWC - fault code description ME | Right O2 sensor upstream of TWC for cylinders 1 to 3, cycle duration too long | AD07.61-P-4000-07LA |
| P2008 (P0135) | O2 sensor heater - fault code description ME | Right O2 sensor upstream of TWC for cylinders 1 to 3, internal resistance | AD07.61-P-4000-08L |
| P2009 (P0141) | O2 sensor heater - fault code description ME | Right O2 downstream of TWC for cylinders 1 to 3, internal resistance | AD07.61-P-4000-08L |
| P2088 (P0135) | O2 sensor heater - fault code description ME | Right O2 sensor upstream of TWC for cylinders 4 to 6, internal resistance | AD07.61-P-4000-08L |
| P2089 (P0141) | O2 sensor heater - fault code description ME | Right O2 downstream of TWC for cylinders 4 to 6, internal resistance | AD07.61-P-4000-08L |
| P20B3 (P0155) | O2 sensor heater - fault code description ME | Left O2 sensor upstream of TWC for cylinders 7 to 9, internal resistance | AD07.61-P-4000-08L |
| P20B4 (P0155) | O2 sensor heater - fault code description ME | Left O2 sensor upstream of TWC for cylinders 10 to 12, internal resistance | AD07.61-P-4000-08L |
| P20B5 (P0161) | O2 sensor heater - fault code description ME | Left O2 sensor downstream of TWC for cylinders 7 to 9, internal resistance | AD07.61-P-4000-08L |
| P20B6 (P0161) | O2 sensor heater - fault code description ME | Left O2 2 sensor downstream of TWC for cylinders 10 to 12, internal resistance | AD07.61-P-4000-08L |
| P20BE (P0135) | O2 sensor heater - fault code description ME | Right O2 2 sensor upstream of TWC for cylinders 1 to 3, voltage supply | AD07.61-P-4000-08LA |
| P20BF (P0135) | O2 sensor heater - fault code description ME | Right O2 2 sensor upstream of TWC for cylinders 4 to 6, voltage supply | AD07.61-P-4000-08LA |
| P20C0 (P0155) | O2 sensor heater - fault code description ME | Left O2 sensor upstream of TWC for cylinders 7 to 9, voltage supply | AD07.61-P-4000-08LA |
| P20C1 (P0155) | O2 sensor heater - fault code description ME | Left O2 sensor upstream of TWC for cylinders 10 to 12, voltage supply | AD07.61-P-4000-08LA |
| P20C2 (P0141) | O2 sensor heater - fault code description ME | Right O2 downstream of TWC for cylinders 1 to 3, voltage supply | AD07.61-P-4000-08LA |
| P20C3 (P0141) | O2 sensor heater - fault code description ME | Right O2 downstream of TWC for cylinders 4 to 6, voltage supply | AD07.61-P-4000-08LA |
| P20C4 (P0161) | O2 sensor heater - fault code description ME | Left O2 sensor downstream of TWC for cylinders 7 to 9, voltage supply | AD07.61-P-4000-08LA |
| P20C5 (P0161) | O2 sensor heater - fault code description ME | Left O2 sensor downstream of TWC for cylinders 10 to 12, voltage supply | AD07.61-P-4000-08LA |
| P2018 (-) | Self-adaptation of mixture formation at its limit - fault code description ME | for cylinders 1 to 3, Between idle speed and part load | AD07.61-P-4000-09LA |
| P2087 (-) | Self-adaptation of mixture formation at its limit - fault code description ME | for cylinders 4 to 6, Between idle speed and part load | AD07.61-P-4000-09LA |
| P20B1 (-) | Self-adaptation of mixture formation at its limit - fault code description ME | for cylinders 7 to 9, Between idle speed and part load | AD07.61-P-4000-09LA |
| P20B2 (-) | Self-adaptation of mixture formation at its limit - fault code description ME | for cylinders 10 to 12, Between idle speed and part load | AD07.61-P-4000-09LA |
| P2017 (P0170) | Self-adaptation of mixture formation at its limit - fault code description ME | for cylinders 1 to 3, in idle | AD07.61-P-4000-09LB |
| P2086 (P0170) | Self-adaptation of mixture formation at its limit - fault code description ME | for cylinders 4 to 6, in idle | AD07.61-P-4000-09LB |
| P20AF (P0173) | Self-adaptation of mixture formation at its limit - fault code description ME | for cylinders 7 to 9, in idle | AD07.61-P-4000-09LB |
| P20B0 (P0173) | Self-adaptation of mixture formation at its limit - fault code description ME | for cylinders 10 to 12, in idle | AD07.61-P-4000-09LB |
| P2016 (P0170) | Self-adaptation of mixture formation at its limit - fault code description ME | for cylinders 1 to 3, In the case of part load | AD07.61-P-4000-09LC |
| P2085 (P0170) | Self-adaptation of mixture formation at its limit - fault code description ME | for cylinders 4 to 6, In the case of part load | AD07.61-P-4000-09LC |
| P20AD (P0173) | Self-adaptation of mixture formation at its limit - fault code description ME | for cylinders 7 to 9, In the case of part load | AD07.61-P-4000-09LC |
| P20AE (P0173) | Self-adaptation of mixture formation at its limit - fault code description ME | for cylinders 10 to 12, In the case of part load | AD07.61-P-4000-09LC |
| P201D (P0201) | Fault code description for fuel injection valves, ME | Cylinder 1 | AD07.61-P-4000-10L |
| P2021 (P0202) | Fault code description for fuel injection valves, ME | Cylinder 2 | AD07.61-P-4000-10L |
| P201F (P0203) | Fault code description for fuel injection valves, ME | Cylinder 3 | AD07.61-P-4000-10L |
| P2022 (P0204) | Fault code description for fuel injection valves, ME | Cylinder 4 | AD07.61-P-4000-10L |
| P201E (P0205) | Fault code description for fuel injection valves, ME | Cylinder 5 | AD07.61-P-4000-10L |
| P2020 (P0206) | Fault code description for fuel injection valves, ME | Cylinder 6 | AD07.61-P-4000-10L |
| P208A (P0207) | Fault code description for fuel injection valves, ME | Cylinder 7 | AD07.61-P-4000-10L |
| P20Bb (P0208) | Fault code description for fuel injection valves, ME | Cylinder 8 | AD07.61-P-4000-10L |
| P20B9 (P0209) | Fault code description for fuel injection valves, ME | Cylinder 9 | AD07.61-P-4000-10L |
| P20BC (P0210) | Fault code description for fuel injection valves, ME | Cylinder 10 | AD07.61-P-4000-10L |
| P208B (P0211) | Fault code description for fuel injection valves, ME | Cylinder 11 | AD07.61-P-4000-10L |
| P20Ba (P0212) | Fault code description for fuel injection valves, ME | Cylinder 12 | AD07.61-P-4000-10L |
| P2043 (P0300) | Fault code description - ME - misfires | Sum, emission limit | AD07.61-P-4000-11L |
| P2044 (P0301) | Fault code description - ME - misfires | Misfire at cylinder 1 | AD07.61-P-4000-11L |
| P2045 (P0305) | Fault code description - ME - misfires | Misfire at cylinder 5 | AD07.61-P-4000-11L |
| P2046 (P0303) | Fault code description - ME - misfires | Misfire at cylinder 3 | AD07.61-P-4000-11L |
| P2047 (P0306) | Fault code description - ME - misfires | Misfire at cylinder 6 | AD07.61-P-4000-11L |
| P2048 (P0302) | Fault code description - ME - misfires | Misfire at cylinder 2 | AD07.61-P-4000-11L |
| P2049 (P0304) | Fault code description - ME - misfires | Misfire at cylinder 4 | AD07.61-P-4000-11L |
| P204A (P0307) | Fault code description - ME - misfires | Misfire at cylinder 7 | AD07.61-P-4000-11L |
| P204B (P0311) | Fault code description - ME - misfires | Misfire at cylinder 11 | AD07.61-P-4000-11L |
| P204C (P0309) | Fault code description - ME - misfires | Misfire at cylinder 9 | AD07.61-P-4000-11L |
| P204D (P0312) | Fault code description - ME - misfires | Misfire at cylinder 12 | AD07.61-P-4000-11L |
| P204E (P0308) | Fault code description - ME - misfires | Misfire at cylinder 8 | AD07.61-P-4000-11L |
| P204F (P0310) | Fault code description - ME - misfires | Misfire at cylinder 10 | AD07.61-P-4000-11L |
| P2050 (P0300) | Fault code description - ME - misfires | Sum, damaging to TWC | AD07.61-P-4000-11LA |
| P2051 (P0301) | Fault code description - ME - misfires | Misfire at cylinder 1 | AD07.61-P-4000-11LA |
| P2052 (P0305) | Fault code description - ME - misfires | Misfire at cylinder 5 | AD07.61-P-4000-11LA |
| P2053 (P0303) | Fault code description - ME - misfires | Misfire at cylinder 3 | AD07.61-P-4000-11LA |
| P2054 (P0306) | Fault code description - ME - misfires | Misfire at cylinder 6 | AD07.61-P-4000-11LA |
| P2055 (P0302) | Fault code description - ME - misfires | Misfire at cylinder 2 | AD07.61-P-4000-11LA |
| P2056 (P0304) | Fault code description - ME - misfires | Misfire at cylinder 4 | AD07.61-P-4000-11LA |
| P2057 (P0307) | Fault code description - ME - misfires | Misfire at cylinder 7 | AD07.61-P-4000-11LA |
| P2058 (P0311) | Fault code description - ME - misfires | Misfire at cylinder 11 | AD07.61-P-4000-11LA |
| P2059 (P0309) | Fault code description - ME - misfires | Misfire at cylinder 9 | AD07.61-P-4000-11LA |
| P205A (P0312) | Fault code description - ME - misfires | Misfire at cylinder 12 | AD07.61-P-4000-11LA |
| P205B (P0308) | Fault code description - ME - misfires | Misfire at cylinder 8 | AD07.61-P-4000-11LA |
| P205C (P0310) | Fault code description - ME - misfires | Misfire at cylinder 10 | AD07.61-P-4000-11LA |
| P2034 (P0335) | Fault code description for crankshaft position sensor, ME | AD07.61-P-4000-13L | |
| P201A (P0341) | Camshaft Hall sensor - fault code description ME | Camshaft Hall sensor for right cylinder bank | AD07.61-P-4000-14L |
| P20B8 (P0340) | Camshaft Hall sensor - fault code description ME | Camshaft Hall sensor for left cylinders bank | AD07.61-P-4000-14L |
| P2003 (P0410) | Air injection: malfunction (function chain) Fault code description ME | right cylinder bank, cylinders 1 to 6 | AD07.61-P-4000-15L |
| P20C9 (P0410) | Air injection: malfunction (function chain) Fault code description ME | left cylinder bank, cylinders 7 to 12 | AD07.61-P-4000-15L |
| P200B (P0422) | Fault code description - three-way catalytic converter effectiveness too low | Catalytic converter for cylinders 1 to 3 | AD07.61-P-4000-16L |
| P207E (P0422) | Fault code description - three-way catalytic converter effectiveness too low | Catalytic converter for cylinders 4 to 6 | AD07.61-P-4000-16L |
| P20A3 (P0432) | Fault code description - three-way catalytic converter effectiveness too low | Catalytic converter for cylinders 7 to 9 | AD07.61-P-4000-16L |
| P20A4 (P0432) | Fault code description - three-way catalytic converter effectiveness too low | Catalytic converter for cylinders 10 to 12 | AD07.61-P-4000-16L |
| P2015 (P0440) | Purge control system has leak (function chain) Fault code description ME | AD07.61-P-4000-17L | |
| P2013 (P0455) | Purge control system has leak (function chain) Fault code description ME | AD07.61-P-4000-17L | |
| P2014 (P0422) | Purge control system has leak (function chain) Fault code description ME | AD07.61-P-4000-17L | |
| P2075 (P0442) | Purge control system has leak (function chain) Fault code description ME | AD07.61-P-4000-17L | |
| P2026 (P0443) | Fault code description for purge control valve, ME | AD07.61-P-4000-19L | |
| P2025 (P0446) | Activated charcoal canister shut-off valve ME - fault code description | AD07.61-P-4000-20L | |
| P2012 (P0446) | Activated charcoal canister shut-off valve ME - fault code description | AD07.61-P-4000-20L | |
| P201C (P0450) | Tank pressure sensor ME - fault code description | AD07.61-P-4000-21L | |
| P2072 (P0450) | Tank pressure sensor ME - fault code description | AD07.61-P-4000-21LA | |
| P202B (P0507) | Idle speed control - fault code description ME | AD07.61-P-4000-24L | |
| P2069 (P0700) | Engaged gear implausible or transmission leaky - fault code description ME | AD07.61-P-4000-27L | |
| P206A (P0700) | Command valve jams in the pressure position - fault code description ME | AD07.61-P-4000-28L | |
| P205E (P0702) | ETC control unit ME - fault code description | Internal fault | AD07.61-P-4000-29L |
| P2067 (P0705) | ETC control unit ME - fault code description | Selector lever module wrongly coded | AD07.61-P-4000-29L |
| P2068 (P0720) | ETC control unit ME - fault code description | CAN message re wheel speed at rear from ESP control unit missing or faulty | AD07.61-P-4000-29L |
| P20D5 (P0702) | ETC control unit ME - fault code description | The torque request from the EGS control unit is implausible. | AD07.61-P-4000-29L |
| P20D6 (P0702) | ETC control unit ME - fault code description | CAN transmission error of torque request from ETC [EGS] control unit | AD07.61-P-4000-29L |
| P20D7 (P0702) | ETC control unit ME - fault code description | CAN transmission error of torque request from ETC [EGS] control unit | AD07.61-P-4000-29L |
| P2065 (P0702) | Supply voltage for valves - fault code description ME | AD07.61-P-4000-30L | |
| P2066 (P0715) | Supply voltage and function of rpm sensors - fault code description ME | AD07.61-P-4000-31L | |
| P20Ca (P0500) | CAN fault detection ME - fault code description | Vehicle speed signal for left rear wheel from ESP control unit | AD07.61-P-4000-32LA |
| P20Cb (P0500) | CAN fault detection ME - fault code description | Vehicle speed signal for left front wheel from ESP control unit | AD07.61-P-4000-32LB |
| P2031 (P0600) | CAN fault detection ME - fault code description | CAN message from steering column module | AD07.61-P-4000-32LC |
| P202F (P0600) | CAN fault detection ME - fault code description | CAN message from ABC control unit | AD07.61-P-4000-32LD |
| P2037 (P0600) | CAN fault detection ME - fault code description | CAN message from ETC [EGS] control unit | AD07.61-P-4000-32LE |
| P2030 (P0600) | CAN fault detection ME - fault code description | CAN message from electronic selector lever module control unit | AD07.61-P-4000-32LF |
| P2036 (P0600) | CAN fault detection ME - fault code description | CAN message from ESP control unit | AD07.61-P-4000-32LG |
| P20D1 (-) | CAN fault detection ME - fault code description | Torque request from DTR control unit implausible | AD07.61-P-4000-32LH |
| P20D2 (-) | CAN fault detection ME - fault code description | CAN transmission error of torque request from DTR control unit | AD07.61-P-4000-32LH |
| P20D3 (-) | CAN fault detection ME - fault code description | CAN transmission error of torque request from DTR control unit | AD07.61-P-4000-32LH |
| P20D9 (-) | CAN fault detection ME - fault code description | Torque request from ESP control unit implausible | AD07.61-P-4000-32LJ |
| P20Da (-) | CAN fault detection ME - fault code description | CAN transmission error of torque request from ESP control unit | AD07.61-P-4000-32LJ |
| P20Db (-) | CAN fault detection ME - fault code description | CAN transmission error of torque request from ESP control unit | AD07.61-P-4000-32LJ |
| P20E4 (-) | CAN fault detection ME - fault code description | Implausible signal from stop lamp switch | AD07.61-P-4000-32LK |
| P20E5 (-) | CAN fault detection ME - fault code description | CAN transmission error of signal from stop lamp switch | AD07.61-P-4000-32LK |
| P20E6 (-) | CAN fault detection ME - fault code description | CAN transmission error of signal from stop lamp switch | AD07.61-P-4000-32LK |
| P203E (P0600) | CAN fault detection ME - fault code description | CAN message from instrument cluster | AD07.61-P-4000-32LL |
| P206D (P0730) | Gear position comparison negative (on multiple occasions) - fault code description ME | AD07.61-P-4000-33L | |
| P206B (P0740) | Torque converter lockup clutch - fault code description ME | AD07.61-P-4000-34L | |
| P2062 (P0743) | Pulse width modulation solenoid valve for torque converter lockup - fault code description ME | AD07.61-P-4000-35L | |
| P2063 (P0748) | Modulating pressure control solenoid valve - fault code description ME | AD07.61-P-4000-36L | |
| P2064 (P0748) | Shift pressure control solenoid valve - fault code description ME | AD07.61-P-4000-37L | |
| P205F (P0753) | Solenoid valve 1-2/4-5 for shift mechanism - fault code description ME | AD07.61-P-4000-38L | |
| P2060 (P0758) | Solenoid valve 2-3 for shift mechanism - fault code description ME | AD07.61-P-4000-39L | |
| P2061 (P0763) | Solenoid valve 3-4 for shift mechanism - fault code description ME | AD07.61-P-4000-40L | |
| P2029 (P0340) | Camshaft timing (function chain) Fault code description ME | Right cylinder bank | AD07.61-P-4000-43L |
| P202A (P0340) | Camshaft timing (function chain) Fault code description ME | Left bank of cylinders | AD07.61-P-4000-43L |
| P20CF (P0120) | Fault code description for pedal value sensor, ME | Voltage difference between signal 1 and signal 2 | AD07.61-P-4000-45L |
| P20DC (P0120) | Fault code description for pedal value sensor, ME | Open circuit on signal path 1 | AD07.61-P-4000-45L |
| P20DD (P0120) | Fault code description for pedal value sensor, ME | Short circuit on signal path 1 | AD07.61-P-4000-45L |
| P20DE (P0120) | Fault code description for pedal value sensor, ME | Open circuit on signal path 2 | AD07.61-P-4000-45L |
| P20DF (P0120) | Fault code description for pedal value sensor, ME | Short circuit on signal path 2 | AD07.61-P-4000-45L |
| P20E3 (P0120) | Fault code description for pedal value sensor, ME | Voltage supply for pedal value sensor | AD07.61-P-4000-45L |
| P2032 (P0120) | Throttle valve actuator ME - fault code description | Actual value potentiometer | AD07.61-P-4000-49L |
| P2097 (-) | Throttle valve actuator ME - fault code description | Throttle valve jams, iced up | AD07.61-P-4000-49LA |
| P202E (P0120) | Throttle valve actuator ME - fault code description | Adjustment | AD07.61-P-4000-49LB |
| P209C (-) | Cylinder shutoff valve does not close for cylinder shutoff OFF - fault code description ME | Cylinder shutoff valve for cylinders 7 to 9 | AD07.61-P-4000-52L |
| P209D (-) | Cylinder shutoff valve does not close for cylinder shutoff OFF - fault code description ME | Cylinder shutoff valve for cylinders 10 to 12 | AD07.61-P-4000-52L |
| P20A2 (-) | An inlet valve for cylinder is not operated at cylinder cutoff OFF-fault code description ME. | AD07.61-P-4000-55L | |
| P208E (-) | Cylinder shutoff valve - fault code description ME | Cylinders 10 to 12, coil 1 | AD07.61-P-4000-56L |
| P208F (-) | Cylinder shutoff valve - fault code description ME | Cylinders 10 to 12, coil 2 | AD07.61-P-4000-56L |
| P2092 (-) | Cylinder shutoff valve - fault code description ME | Cylinders 7 to 9, coil 1 | AD07.61-P-4000-56L |
| P2093 (-) | Cylinder shutoff valve - fault code description ME | Cylinders 7 to 9, coil 2 | AD07.61-P-4000-56L |
| P209B (-) | Exhaust flap switchover valve - fault code description ME | AD07.61-P-4000-57L | |
| P2091 (P0520) | Cylinder shutoff oil pressure sensor - fault code description ME | AD07.61-P-4000-58L | |
| P201B (P0560) | ME control unit voltage supply - fault code description | AD07.61-P-4000-59L | |
| P2039 (-) | Oil sensor - fault code description, ME | Oil level implausible | AD07.61-P-4000-60L |
| P2040 (-) | Oil sensor - fault code description, ME | Oil quality implausible | AD07.61-P-4000-60L |
| P2041 (-) | Oil sensor - fault code description, ME | Water in engine oil | AD07.61-P-4000-60L |
| P2076 (-) | Oil sensor - fault code description, ME | Oil temperature implausible | AD07.61-P-4000-60L |
| P2099 (-) | An exhaust valve for cylinder is not operated at cylinder cutoff OFF-fault code description ME. | Cylinder 8 | AD07.61-P-4000-61L |
| P209A (-) | An exhaust valve for cylinder is not operated at cylinder cutoff OFF-fault code description ME. | Cylinder 10 | AD07.61-P-4000-61L |
| P209E (-) | An exhaust valve for cylinder is not operated at cylinder cutoff OFF-fault code description ME. | Cylinder 7 | AD07.61-P-4000-61L |
| P209F (-) | An exhaust valve for cylinder is not operated at cylinder cutoff OFF-fault code description ME. | Cylinder 11 | AD07.61-P-4000-61L |
| P20A0 (-) | An exhaust valve for cylinder is not operated at cylinder cutoff OFF-fault code description ME. | Cylinder 9 | AD07.61-P-4000-61L |
| P20A1 (-) | An exhaust valve for cylinder is not operated at cylinder cutoff OFF-fault code description ME. | Cylinder 12 | AD07.61-P-4000-61L |
| P2098 (-) | Crash signal implausible - fault code description, ME | AD07.61-P-4000-62L | |
| P207D (-) | EIS control unit - fault code description, ME | AD07.61-P-4000-63L | |
| P203A (P0460) | Fill level of fuel tank - fault code description ME | AD07.61-P-4000-64L | |
| P20CD (-) | Air conditioning - fault code description ME | AC compressor torque implausible | AD07.61-P-4000-65L |
| P20CE (-) | Air conditioning - fault code description ME | Refrigerant pressure in air conditioning too high | AD07.61-P-4000-65L |
| P20D0 (-) | Air conditioning - fault code description ME | The air conditioning requests an implausible fan output. | AD07.61-P-4000-65L |
| P20D8 (-) | ESP control unit - fault code description, ME | ESP fault | AD07.61-P-4000-66L |
| P206E (-) | Transmission version implausible - fault code description ME | Coded as having a manual transmission, vehicle has automatic gear selection | AD07.61-P-4000-67L |
| P206F (-) | Transmission version implausible - fault code description ME | Wrongly coded or fault in CAN communication with ETC [EGS] control unit | AD07.61-P-4000-67L |
| P2070 (-) | Transmission version implausible - fault code description ME | Undervoltage on ETC [EGS] control unit | AD07.61-P-4000-67L |
| P20E7 (P0301) | Ion current signal from a cylinder implausible fault code description ME | Cylinder 1 | AD07.61-P-4000-68L |
| P20E8 (P0302) | Ion current signal from a cylinder implausible fault code description ME | Cylinder 2 | AD07.61-P-4000-68L |
| P20E9 (P0303) | Ion current signal from a cylinder implausible fault code description ME | Cylinder 3 | AD07.61-P-4000-68L |
| P20Ea (P0304) | Ion current signal from a cylinder implausible fault code description ME | Cylinder 4 | AD07.61-P-4000-68L |
| P20Eb (P0305) | Ion current signal from a cylinder implausible fault code description ME | Cylinder 5 | AD07.61-P-4000-68L |
| P20EC (P0306) | Ion current signal from a cylinder implausible fault code description ME | Cylinder 6 | AD07.61-P-4000-68L |
| P20F3 (P0307) | Ion current signal from a cylinder implausible fault code description ME | Cylinder 7 | AD07.61-P-4000-68L |
| P20F4 (P0308) | Ion current signal from a cylinder implausible fault code description ME | Cylinder 8 | AD07.61-P-4000-68L |
| P20F5 (P0309) | Ion current signal from a cylinder implausible fault code description ME | Cylinder 9 | AD07.61-P-4000-68L |
| P20F6 (P0310) | Ion current signal from a cylinder implausible fault code description ME | Cylinder 10 | AD07.61-P-4000-68L |
| P20F7 (P0311) | Ion current signal from a cylinder implausible fault code description ME | Cylinder 11 | AD07.61-P-4000-68L |
| P20F8 (P0312) | Ion current signal from a cylinder implausible fault code description ME | Cylinder 12 | AD07.61-P-4000-68L |
| P2023 (P0410) | Air injection relay - fault code description ME | AD07.61-P-4000-69L | |
| P2019 (-) | Antiboil protection for coolant - fault code description ME | AD07.61-P-4000-70L | |
| P2073 (-) | Electrical suction-type fan - fault code description, ME | AD07.61-P-4000-71L | |
| P2090 (-) | Connectors on O2 sensors wrong way round - fault code description ME | AD07.61-P-4000-72L | |
| P2033 (-) | Cruise control pushbutton switch - fault code description ME | AD07.61-P-4000-73L | |
| P2042 (-) | Safety fuel cut-off detected - fault code description ME | AD07.61-P-4000-74L | |
| P202C (P0115) | Coolant thermostat - fault code description, ME | AD07.61-P-4000-76L | |
| P20BD (P0378) | Angular deviation of camshaft relative to crankshaft - fault code description ME | Camshaft for left cylinder bank to crankshaft | AD07.61-P-4000-77L |
| P203D (P0370) | Angular deviation of camshaft relative to crankshaft - fault code description ME | Camshaft for right cylinder bank to crankshaft | AD07.61-P-4000-77LA |
| P2024 (P0412) | Air pump switchover valve - fault code description, ME | Right cylinder bank | AD07.61-P-4000-78L |
| P20C8 (P0415) | Air pump switchover valve - fault code description, ME | Left bank of cylinders | AD07.61-P-4000-78L |
| P2028 (P0340) | Camshaft adjustment valve - fault code description ME | Right cylinder bank | AD07.61-P-4000-79L |
| P208C (P0340) | Camshaft adjustment valve - fault code description ME | Left bank of cylinders | AD07.61-P-4000-79L |
| P20ED (-) | Spark plug a or b of a cylinder - fault code description ME | Cylinder 1 | AD07.61-P-4000-80L |
| P20EE (-) | Spark plug a or b of a cylinder - fault code description ME | Cylinder 2 | AD07.61-P-4000-80L |
| P20EF (-) | Spark plug a or b of a cylinder - fault code description ME | Cylinder 3 | AD07.61-P-4000-80L |
| P20E0 (-) | Spark plug a or b of a cylinder - fault code description ME | Cylinder 4 | AD07.61-P-4000-80L |
| P20F1 (-) | Spark plug a or b of a cylinder - fault code description ME | Cylinder 5 | AD07.61-P-4000-80L |
| P20F2 (-) | Spark plug a or b of a cylinder - fault code description ME | Cylinder 6 | AD07.61-P-4000-80L |
| P20F9 (-) | Spark plug a or b of a cylinder - fault code description ME | Cylinder 7 | AD07.61-P-4000-80L |
| P20Fa (-) | Spark plug a or b of a cylinder - fault code description ME | Cylinder 8 | AD07.61-P-4000-80L |
| P20Fb (-) | Spark plug a or b of a cylinder - fault code description ME | Cylinder 9 | AD07.61-P-4000-80L |
| P20FC (-) | Spark plug a or b of a cylinder - fault code description ME | Cylinder 10 | AD07.61-P-4000-80L |
| P20FD (-) | Spark plug a or b of a cylinder - fault code description ME | Cylinder 11 | AD07.61-P-4000-80L |
| P20FE (-) | Spark plug a or b of a cylinder - fault code description ME | Cylinder 12 | AD07.61-P-4000-80L |
| P20D4 (-) | Load limitation active - fault code description ME | AD07.61-P-4000-82AA | |
| P203B (P0221) | ME control unit - fault code description, ME | Fault in function monitoring | AD07.61-P-4000-91L |
| P203C (P0221) | ME control unit - fault code description, ME | Fault in function monitoring | AD07.61-P-4000-91L |