ME fuel injection and ignition system (ME), DTC memory - AD07.61-P-4000BC
ENGINES 113.940 /941 /942 /943 /960 as of 1.6.00
ENGINES 113.948 /961 /963 /964 /965 /966 /967 /968 / 969 /971
| All checks on the electrical system gasoline injection system ME engine 113 are described in STAR DIAGNOSIS The following list contains the fault code description for the corresponding fault code |
||||
| Fault code STAR DIAGNOSIS ( |
Possible cause | Note | Fault code description | |
| P2001 | (P0400) | Exhaust gas recirculation malfunction (function chain) - fault code description ME | AD07.61-P-4000-50AA | |
| P2003 | (P0410) | ME secondary air injection malfunction (causal chain) - fault code description | AD07.61-P-4000-15AA | |
| P2004 | (P0100) | Hot-film mass-air sensor ME - fault code description | AD07.61-P-4000-01BA | |
| P2005 | (P0115) | Coolant temperature sensor ME - fault code description | AD07.61-P-4000-04L | |
| P2006 | (P0110) | Intake air temperature sensor ME - fault code description | AD07.61-P-4000-03L | |
| P2007 | (P0105) | Pressure sensor ME - fault code description | AD07.61-P-4000-02L | |
| P2008 | (P0135) | O2-sensor heating - fault code description ME | Right O2 sensor upstream of TWC, internal resistance | AD07.61-P-4000-08AA |
| P2009 | (P0141) | O2-sensor heating - fault code description ME | Right O2 sensor downstream of TWC, internal resistance | AD07.61-P-4000-08AA |
| P200A | (-) | Anti-knock control in the control unit - hardware fault - fault code description ME | AD07.61-P-4000-41AA | |
| P200B | (P0422) | Fault code description - three-way catalytic converter effectiveness too low | Right catalytic converter | AD07.61-P-4000-16AA |
| P200C | (-) | Aging of O2 sensor upstream of TWC - fault code description ME | Right O2 sensor upstream of TWC, correction parameter limit exceeded | AD07.61-P-4000-07AA |
| P200D | (P0133) | Aging of O2 sensor upstream of TWC - fault code description ME | Right O2 sensor upstream of TWC, cycle duration | AD07.61-P-4000-07AB |
| P200E | (-) | O2 sensor signal - fault code description ME | Right O2 sensor downstream of TWC, no sensor condition change | AD07.61-P-4000-06AA |
| P200F | (P0130) | O2 sensor signal - fault code description ME | Right O2 sensor upstream of TWC, electrical fault | AD07.61-P-4000-06AB |
| P2010 | (P0136) | O2 sensor signal - fault code description ME | Right O2 sensor downstream of TWC, electrical fault | AD07.61-P-4000-06AB |
| P2011 | (-) | Knock sensor ME - fault code description | Right knock sensor 1 | AD07.61-P-4000-12AA |
| P2012 | (P0446) | Activated charcoal canister shut-off valve ME - fault code description | AD07.61-P-4000-20L | |
| P2013 | (P0455) | Purge control system has leak (function chain) Fault code description ME | AD07.61-P-4000-17L | |
| P2014 | (P0422) | Purge control system has leak (function chain) Fault code description ME | AD07.61-P-4000-17L | |
| P2015 | (P0440) | Purge control system has leak (function chain) Fault code description ME | AD07.61-P-4000-17L | |
| P2016 | (P0170) | Self-adaptation of mixture formation at its limit - fault code description ME | For the right cylinder bank, at partial load | AD07.61-P-4000-09AC |
| P2017 | (P0170) | Self-adaptation of mixture formation at its limit - fault code description ME | For the right cylinder bank, when idling | AD07.61-P-4000-09AB |
| P2018 | (-) | Self-adaptation of mixture formation at its limit -fault code description ME | For the right cylinder bank, between idle and partial load | AD07.61-P-4000-09AA |
| P2019 | (-) | Antiboil protection for coolant - fault code description ME | AD07.61-P-4000-70L | |
| P201A | (P0341) | Camshaft Hall sensor - fault code description ME | AD07.61-P-4000-14AA | |
| P201B | (P0560) | ME control unit voltage supply - fault code description | AD07.61-P-4000-59L | |
| P201C | (P0450) | Tank pressure sensor ME - fault code description | AD07.61-P-4000-21L | |
| P201D | (P0201) | Fault code description for fuel injection valves, ME | Cylinder 1 | AD07.61-P-4000-10BA |
| P201E | (P0205) | Fault code description for fuel injection valves, ME | Cylinder 5 | AD07.61-P-4000-10BA |
| P201F | (P0204) | Fault code description for fuel injection valves, ME | Cylinder 4 | AD07.61-P-4000-10BA |
| P2020 | (P0202) | Fault code description for fuel injection valves, ME | Cylinder 2 | AD07.61-P-4000-10BA |
| P2021 | (P0206) | Fault code description for fuel injection valves, ME | Cylinder 6 | AD07.61-P-4000-10BA |
| P2022 | (P0203) | Fault code description for fuel injection valves, ME | Cylinder 3 | AD07.61-P-4000-10BA |
| P2023 | (P0410) | Air injection relay - fault code description ME | AD07.61-P-4000-69L | |
| P2024 | (P0412) | Air pump switchover valve - fault code description, ME | AD07.61-P-4000-78A | |
| P2025 | (P0446) | Activated charcoal canister shut-off valve ME - fault code description | AD07.61-P-4000-20L | |
| P2026 | (P0443) | Fault code description for purge control valve, ME | AD07.61-P-4000-19L | |
| P2027 | (P0403) | EGR [ARF] vacuum transducer - fault code description ME | AD07.61-P-4000-51AA | |
| P202B | (P0507) | Idle speed control - fault code description ME | AD07.61-P-4000-24L | |
| P202C | (P0115) | Coolant thermostat - fault code description, ME | AD07.61-P-4000-76L | |
| P202D | (P0115) | Coolant temperature sensor ME - fault code description | AD07.61-P-4000-04LA | |
| P202E | (P0120) | Throttle valve actuator ME - fault code description | Adjustment | AD07.61-P-4000-49LB |
| P202F | (P0600) | CAN fault detection ME - fault code description | CAN message from ABC control unit | AD07.61-P-4000-32LD |
| P2030 | (P0600) | CAN fault detection ME - fault code description | CAN message from electronic selector lever module control unit | AD07.61-P-4000-32LF |
| P2031 | (P0600) | CAN fault detection ME - fault code description | CAN message from steering column module | AD07.61-P-4000-32LC |
| P2032 | (P0120) | Throttle valve actuator ME - fault code description | Actual value potentiometer | AD07.61-P-4000-49L |
| P2033 | (-) | Cruise control pushbutton switch - fault code description ME | AD07.61-P-4000-73L | |
| P2034 | (P0335) | Fault code description for crankshaft position sensor, ME | AD07.61-P-4000-13L | |
| P2036 | (P0600) | CAN fault detection ME - fault code description | CAN message from ESP control unit | AD07.61-P-4000-32LG |
| P2037 | (P0600) | CAN fault detection ME - fault code description | CAN message from ETC [EGS] control unit Transmission 722.6 | AD07.61-P-4000-32LE |
| P2038 | (-) | Knock sensor ME - fault code description | Left knock sensor 2 | AD07.61-P-4000-12AA |
| P2039 | (-) | Oil sensor - fault code description, ME | Oil level implausible | AD07.61-P-4000-60L |
| P203A | (P0460) | Fill level of fuel tank - fault code description ME | AD07.61-P-4000-64L | |
| P203B | (P0221) | ME control unit - fault code description, ME | Fault in function monitoring | AD07.61-P-4000-91L |
| P203C | (P0221) | ME control unit - fault code description, ME | Fault in function monitoring | AD07.61-P-4000-91L |
| P203D | (P0370) | Angular deviation of camshaft relative to crankshaft - fault code description ME | AD07.61-P-4000-77A | |
| P203E | (P0600) | CAN fault detection ME - fault code description | CAN message from instrument cluster | AD07.61-P-4000-32LL |
| P2040 | (-) | Oil sensor - fault code description, ME | Oil quality implausible | AD07.61-P-4000-60L |
| P2041 | (-) | Oil sensor - fault code description, ME | Water in engine oil | AD07.61-P-4000-60L |
| P2042 | (-) | Safety fuel cut-off detected - fault code description ME | AD07.61-P-4000-74L | |
| P2043 | (P0300) | Fault code description - ME - misfires | Sum, emission limit | AD07.61-P-4000-11BA |
| P2044 | (P0301) | Fault code description - ME - misfires | Misfires on cylinder 1, emission limit | AD07.61-P-4000-11BA |
| P2045 | (P0305) | Fault code description - ME - misfires | Misfires on cylinder 5, emission limit | AD07.61-P-4000-11BA |
| P2046 | (P0304) | Fault code description - ME - misfires | Misfires on cylinder 4, emission limit | AD07.61-P-4000-11BA |
| P2047 | (P0302) | Fault code description - ME - misfires | Misfires on cylinder 2, emission limit | AD07.61-P-4000-11BA |
| P2048 | (P0306) | Fault code description - ME - misfires | Misfires on cylinder 6, emission limit | AD07.61-P-4000-11BA |
| P2049 | (P0303) | Fault code description - ME - misfires | Misfires on cylinder 3, emission limit | AD07.61-P-4000-11BA |
| P204A | (P0307) | Fault code description - ME - misfires | Misfires on cylinder 7, emission limit | AD07.61-P-4000-11BA |
| P204B | (P0308) | Fault code description - ME - misfires | Misfires on cylinder 8, emission limit | AD07.61-P-4000-11BA |
| P2050 | (P0300) | Fault code description - ME - misfires | Sum, damaging to TWC | AD07.61-P-4000-11BB |
| P2051 | (P0301) | Fault code description - ME - misfires | Misfires on cylinder 1, damaging to TWC | AD07.61-P-4000-11BB |
| P2052 | (P0305) | Fault code description - ME - misfires | Misfires on cylinder 5, damaging to TWC | AD07.61-P-4000-11BB |
| P2053 | (P0304) | Fault code description - ME - misfires | Misfires on cylinder 4, damaging to TWC | AD07.61-P-4000-11BB |
| P2054 | (P0302) | Fault code description - ME - misfires | Misfires on cylinder 2, damaging to TWC | AD07.61-P-4000-11BB |
| P2055 | (P0306) | Fault code description - ME - misfires | Misfires on cylinder 6, damaging to TWC | AD07.61-P-4000-11BB |
| P2056 | (P0303) | Fault code description - ME - misfires | Misfires on cylinder 3, damaging to TWC | AD07.61-P-4000-11BB |
| P2057 | (P0307) | Fault code description - ME - misfires | Misfires on cylinder 7, damaging to TWC | AD07.61-P-4000-11BB |
| P2058 | (P0308) | Fault code description - ME - misfires | Misfires on cylinder 8, damaging to TWC | AD07.61-P-4000-11BB |
| P205E | (P0702) | ETC control unit ME - fault code description | Internal fault Transmission 722.6 |
AD07.61-P-4000-29L |
| P205F | (P0753) | Solenoid valve 1-2/4-5 for shift mechanism - fault code description ME | Transmission 722.6 | AD07.61-P-4000-38L |
| P2060 | (P0758) | Solenoid valve 2-3 for shift mechanism - fault code description ME | Transmission 722.6 | AD07.61-P-4000-39L |
| P2061 | (P0763) | Solenoid valve 3-4 for shift mechanism - fault code description ME | Transmission 722.6 | AD07.61-P-4000-40L |
| P2062 | (P0743) | Pulse width modulation solenoid valve for torque converter lockup - fault code description ME | Transmission 722.6 | AD07.61-P-4000-35L |
| P2063 | (P0748) | Modulating pressure control solenoid valve - fault code description ME | Transmission 722.6 | AD07.61-P-4000-36L |
| P2064 | (P0748) | Shift pressure control solenoid valve - fault code description ME | Transmission 722.6 | AD07.61-P-4000-37L |
| P2065 | (P0702) | Supply voltage for valves - fault code description ME | Transmission 722.6 | AD07.61-P-4000-30L |
| P2066 | (P0715) | Supply voltage and function of rpm sensors - fault code description ME | Transmission 722.6 | AD07.61-P-4000-31L |
| P2067 | (P0705) | ETC control unit ME - fault code description | Selector lever module wrongly coded Transmission 722.6 | AD07.61-P-4000-29L |
| P2068 | (P0720) | ETC control unit ME - fault code description | CAN message re wheel speed at rear from ESP control unit missing or faulty Transmission 722.6 |
AD07.61-P-4000-29L |
| P2069 | (P0700) | Engaged gear implausible or transmission leaky - fault code description ME | Transmission 722.6 | AD07.61-P-4000-27L |
| P206A | (P0700) | Command valve jams in the pressure position - fault code description ME | Transmission 722.6 | AD07.61-P-4000-28L |
| P206B | (P0740) | Torque converter lockup clutch - fault code description ME | Transmission 722.6 | AD07.61-P-4000-34L |
| P206D | (P0730) | Gear position comparison negative (on multiple occasions) - fault code description ME | Transmission 722.6 | AD07.61-P-4000-33L |
| P206E | (-) | Transmission version implausible - fault code description ME | Coded as having a manual transmission, vehicle has automatic gear selection Transmission 722.6 | AD07.61-P-4000-67L |
| P206F | (-) | Transmission version implausible - fault code description ME | Wrongly coded or fault in CAN communication with ETC [EGS] control unit Transmission 722.6 |
AD07.61-P-4000-67L |
| P2070 | (-) | Transmission version implausible - fault code description ME | Transmission 722.6 | AD07.61-P-4000-67L |
| P2072 | (P0450) | Tank pressure sensor ME - fault code description | AD07.61-P-4000-21LA | |
| P2073 | (-) | Electrical suction-type fan - fault code description, ME | AD07.61-P-4000-71L | |
| P2074 | (-) | Variable intake manifold switchover valve - fault code description ME | AD07.61-P-4000-81A | |
| P2075 | (P0442) | Purge control system has leak (function chain) Fault code description ME |
AD07.61-P-4000-17L | |
| P2076 | (-) | Oil sensor - fault code description, ME | Oil temperature implausible | AD07.61-P-4000-60L |
| P2079 | (-) | CAN fault detection ME - fault code description | Speed variable speed limiter | AD07.61-P-4000-32AB |
| P207A | (-) | CAN fault detection ME - fault code description | Speed variable speed limiter | AD07.61-P-4000-32AB |
| P207B | (-) | CAN fault detection ME - fault code description | Selector lever position | AD07.61-P-4000-32AC |
| P207D | (-) | EIS control unit - fault code description, ME | AD07.61-P-4000-63L | |
| P207E | (P0432) | Fault code description - three-way catalytic converter effectiveness too low | Left catalytic converter | AD07.61-P-4000-16AA |
| P207F | (-) | Aging of O2 sensor upstream of TWC - fault code description ME | Left O2 sensor upstream of TWC, correction parameter limit exceeded | AD07.61-P-4000-07AA |
| P2080 | (P0153) | Aging of O2 sensor upstream of TWC - fault code description ME | Left O2 sensor upstream of TWC, cycle duration | AD07.61-P-4000-07AB |
| P2081 | (-) | O2 sensor signal - fault code description ME | Left O2 sensor downstream of TWC, no sensor condition change | AD07.61-P-4000-06AA |
| P2082 | (P0150) | O2 sensor signal - fault code description ME | Left O2 sensor upstream of TWC, electrical fault | AD07.61-P-4000-06AB |
| P2083 | (P0156) | O2 sensor signal - fault code description ME | Left O2 sensor downstream of TWC, electrical fault | AD07.61-P-4000-06AB |
| P2085 | (P0173) | Self-adaptation of mixture formation at its limit - fault code description ME | For the left cylinder bank, at partial load | AD07.61-P-4000-09AC |
| P2086 | (P0173) | Self-adaptation of mixture formation at its limit - fault code description ME | For the left cylinder bank, when idling | AD07.61-P-4000-09AB |
| P2087 | (-) | Self-adaptation of mixture formation at its limit - fault code description ME | For the left cylinder bank, between idle and partial load | AD07.61-P-4000-09AA |
| P2088 | (P0155) | O2-sensor heating - fault code description ME | Left O2 sensor upstream of TWC, internal resistance | AD07.61-P-4000-08AA |
| P2089 | (P0161) | O2-sensor heating - fault code description ME | Left O2 sensor downstream of TWC, internal resistance | AD07.61-P-4000-08AA |
| P208A | (P0207) | Fault code description for fuel injection valves, ME | Cylinder 7 | AD07.61-P-4000-10BA |
| P208B | (P0208) | Fault code description for fuel injection valves, ME | Cylinder 8 | AD07.61-P-4000-10BA |
| P208E | (-) | Cylinder shutoff valve - fault code description ME | Left bank of cylinders with cylinder shutoff (code 479) | AD07.61-P-4000-56BA |
| P208F | (-) | Cylinder shutoff valve - fault code description ME | Left bank of cylinders with cylinder shutoff (code 479) | AD07.61-P-4000-56BA |
| P2090 | (-) | Connectors on O2 sensors wrong way round - fault code description ME | AD07.61-P-4000-72L | |
| P2091 | (P0520) | Cylinder shutoff oil pressure sensor - fault code description ME | with cylinder shutoff (code 479) | AD07.61-P-4000-58L |
| P2092 | (-) | Cylinder shutoff valve - fault code description ME | Right cylinder bank with cylinder shutoff (code 479) |
AD07.61-P-4000-56BA |
| P2093 | (-) | Cylinder shutoff valve - fault code description ME | Right cylinder bank with cylinder shutoff (code 479) |
AD07.61-P-4000-56BA |
| P2094 | (-) | Cylinder shutoff valve does not open for cylinder shutoff ON - fault code description ME | with cylinder shutoff (code 479) | AD07.61-P-4000-53BA |
| P2095 | (-) | Cylinder shutoff (function chain) - fault code description ME | Intake valve from cylinders 2, 3, 5 or 8 with cylinder shutoff (code 479) | AD07.61-P-4000-54BA |
| P20A2 | (-) | An inlet valve for cylinder is not operated at cylinder cutoff OFF- fault code description ME. | with cylinder shutoff (code 479) | AD07.61-P-4000-55BA |
| P2097 | (-) | Throttle valve actuator ME - fault code description | Throttle valve jams, iced up | AD07.61-P-4000-49LA |
| P2098 | (-) | Crash signal implausible - fault code description, ME | AD07.61-P-4000-62L | |
| P209B | (-) | Exhaust flap switchover valve - fault code description ME | AD07.61-P-4000-57L | |
| P209C | (-) | Cylinder shutoff valve does not close for cylinder shutoff OFF - fault code description ME | Right cylinder bank with cylinder shutoff (code 479) |
AD07.61-P-4000-52BA |
| P209D | (-) | Cylinder shutoff valve does not close for cylinder shutoff OFF - fault code description ME | Left bank of cylinders with cylinder shutoff (code 479) |
AD07.61-P-4000-52BA |
| P209E | (-) | Cylinder shutoff (function chain) - fault code description ME | Exhaust valve on cylinder 5 with cylinder shutoff (code 479) |
AD07.61-P-4000-54BA |
| P209F | (-) | Cylinder shutoff (function chain) - fault code description ME | Exhaust valve on cylinder 2 with cylinder shutoff (code 479) |
AD07.61-P-4000-54BA |
| P20A0 | (-) | Cylinder shutoff (function chain) - fault code description ME | Exhaust valve on cylinder 3 with cylinder shutoff (code 479) |
AD07.61-P-4000-54BA |
| P20A1 | (-) | Cylinder shutoff (function chain) - fault code description ME | Exhaust valve on cylinder 8 with cylinder shutoff (code 479) |
AD07.61-P-4000-54BA |
| P20BE | (P0135) | O2-sensor heating - fault code description ME | Right O2 sensor upstream of TWC, voltage supply | AD07.61-P-4000-08AB |
| P20BF | (P0135) | O2-sensor heating - fault code description ME | Left O2 sensor upstream of TWC, voltage supply | AD07.61-P-4000-08AB |
| P20C2 | (P0141) | O2-sensor heating - fault code description ME | Right O2 sensor downstream of TWC, voltage supply | AD07.61-P-4000-08AB |
| P20C3 | (P0141) | O2-sensor heating - fault code description ME | Left O2 sensor downstream of TWC, voltage supply | AD07.61-P-4000-08AB |
| P20Ca | (P0500) | CAN fault detection ME - fault code description | Vehicle speed signal for left rear wheel from ESP control unit | AD07.61-P-4000-32LA |
| P20Cb | (P0500) | CAN fault detection ME - fault code description | Vehicle speed signal for left front wheel from ESP control unit | AD07.61-P-4000-32LB |
| P20CC | (-) | CAN fault detection ME - fault code description | CAN message from ESP control unit missing or faulty | AD07.61-P-4000-32AA |
| P20CD | (-) | Air conditioning - fault code description ME | AC compressor torque implausible | AD07.61-P-4000-65L |
| P20CE | (-) | Air conditioning - fault code description ME | Refrigerant pressure in air conditioning too high | AD07.61-P-4000-65L |
| P20CF | (P0120) | Fault code description for pedal value sensor, ME | Voltage difference between signal 1 and signal 2 | AD07.61-P-4000-45L |
| P20D0 | (-) | Air conditioning - fault code description ME | The air conditioning requests an implausible fan output. | AD07.61-P-4000-65L |
| P20D1 | (-) | CAN fault detection ME - fault code description | Torque request from DTR control unit implausible | AD07.61-P-4000-32LH |
| P20D2 | (-) | CAN fault detection ME - fault code description | CAN transmission error of torque request from DTR control unit | AD07.61-P-4000-32LH |
| P20D3 | (-) | CAN fault detection ME - fault code description | CAN transmission error of torque request from DTR control unit | AD07.61-P-4000-32LH |
| P20D4 | (-) | Load limitation active - fault code description ME | AD07.61-P-4000-82AA | |
| P20D5 | (P0702) | ETC control unit ME - fault code description | The torque request from the EGS control unit is implausible. | AD07.61-P-4000-29L |
| P20D6 | (P0702) | ETC control unit ME - fault code description | CAN transmission error of torque request from ETC [EGS] control unit | AD07.61-P-4000-29L |
| P20D7 | (P0702) | ETC control unit ME - fault code description | CAN transmission error of torque request from ETC [EGS] control unit | AD07.61-P-4000-29L |
| P20D8 | (-) | ESP control unit - fault code description, ME | ESP fault | AD07.61-P-4000-66L |
| P20D9 | (-) | CAN fault detection ME - fault code description | Torque request from ESP control unit implausible | AD07.61-P-4000-32LJ |
| P20Da | (-) | CAN fault detection ME - fault code description | CAN transmission error of torque request from ESP control unit | AD07.61-P-4000-32LJ |
| P20Db | (-) | CAN fault detection ME - fault code description | CAN transmission error of torque request from ESP control unit | AD07.61-P-4000-32LJ |
| P20DC | (P0120) | Fault code description for pedal value sensor, ME | Open circuit on signal path 1 | AD07.61-P-4000-45L |
| P20DD | (P0120) | Fault code description for pedal value sensor, ME | Short circuit at signal path 1 | AD07.61-P-4000-45L |
| P20DE | (P0120) | Fault code description for pedal value sensor, ME | Open circuit on signal path 2 | AD07.61-P-4000-45L |
| P20DF | (P0120) | Fault code description for pedal value sensor, ME | Short circuit at signal path 2 | AD07.61-P-4000-45L |
| P20E3 | (P0120) | Fault code description for pedal value sensor, ME | Voltage supply for pedal value sensor | AD07.61-P-4000-45L |
| P20E4 | (-) | CAN fault detection ME - fault code description | Implausible signal from stop lamp switch | AD07.61-P-4000-32LK |
| P20E5 | (-) | CAN fault detection ME - fault code description | CAN transmission error of signal from stop lamp switch | AD07.61-P-4000-32LK |
| P20E6 | (-) | CAN fault detection ME - fault code description | CAN transmission error of signal from stop lamp switch | AD07.61-P-4000-32LK |