Reset, function - GF54.50-P-2010R

MODELS 203 up to 30.6.02, 208 as of 1.8.99, 210 as of 1.7.99, 215, 220 with CODE (494a) USA version 

The contents of the long-distance memory and short distance memory can be reset with the reset button (right-hand button) of the instrument cluster (A1):

Resetting the long-distance memory ("SINCE RESET") 

• Circuit 15 ON
• Using the system selection button (S110s3) and scroll forward/back button (S110s1) of the multifunction steering wheel, select the "SINCE RESET" display screen
• Operate the reset button for 1 second
• The display is reset (see figure)

The diagram shows the "SINCE RESET" display screen (long-distance memory) after a reset.

The display screen for "SINCE START" (transient memory) resets in the same way.

Manually resetting the short-distance memory ("SINCE START") 

• Terminal 15 ON
• Using the system selection button (S110s3) and scroll forward/back button (S110s1) of P54.50-2027-01 the multifunction steering wheel, select the "SINCE START" display screen (short-distance memory)
• Operate the reset button for 1 second
• The display is reset
  Fig 1: Resetting Long-Distance Memory Display Screen - Since Reset

  

Automatically resetting the short-distance memory ("SINCE START") 

As the "SINCE START" display (short-distance memory) is considered for the data of one driving cycle, the contents of the "SINCE START" display (short-distance memory) are normally reset automatically.

• On model 203 resetting takes place as soon as the instrument cluster (A1) has not been activated for 4 h.
• In models 208, 210, 215 and 220, the reset occurs when the engine is started.

Incorporation of the data from the previous driving cycle in the short-distance memory (except model 203) 

In many cases it can however be meaningful to incorporate the data from the previous driving cycle in the short-distance memory, because, for example, the data for filling the tank during a holiday trip should also be recorded during any interruptions to the trip. The data for the entire trip can then be stored in the long-distance memory ("since reset").

The procedure for this is as follows:

• Using the system selection button and scroll forward/back button, select the "SINCE START" display screen (short-distance memory)
• Start engine
• The "SINCE START" display (short-distance memory) flashes for up to 2 miles or 2 minutes after engine start
• When the display flashes operate the reset button for 1 second
• The values of the previous driving cycle are incorporated in the short-distance memory

  If the display of travel time or travel distance exceeds the maximum display value (99:59 h or 65.535 km (40.959 miles), the travel time and travel distance of the respective memory are automatically reset This preserves the relationship between travel time and mileage.

  After a reset it may take as much as 3 km or 2 min until the trip computer has enough data to display the fuel consumption figures correctly. During this time, depending on the unit setting (kilometers/miles) and the national variant coding of the instrument cluster (A1), the display shows 5.8 MPG, 40 L/100 km or 2.5 km/L.

  	Range, function		GF54.50-P-2006R
  	Travel time, function		GF54.50-P-2004R
  	Fuel consumption, function		GF54.50-P-2007R
  	Distance, function		GF54.50-P-2008R
  	Average speed, function		GF54.50-P-2009R
  	Instrument cluster (IC), operating information	Model 203.0/2	GF54.30-P-0002-05PP
  		Model 203.7	GF54.30-P-0002-05PC
  		Models 208, 210	GF54.30-P-0002-05B
  		Model 215, 220	GF54.30-P-0002-05S
  	Instrument cluster (IC), networking of components	Model 203	GF54.30-P-0002-06PP