Remove/install radius rod - AR35.20-P-0111B: Notes

MODELS 129, 170, 202, 208, 210 

Shown on model 210 

Fig 1: Identifying Radius Rod Remove/Install Components

Modification notes

28.2.98	Diameter of wheel carrier bores modified	MODEL 129, 170, 202, 208 as of 02/98 MODEL 210 as of 01/98	BT35.20-P-0005-01A
28.2.98	Bolted connection, tension arm to wheel carrier modified	MODEL 129, 170, 202, 208 as of 02/98 MODEL 210 as of 01/98	BT35.20-P-0008-01A
28.2.98	If a new tension arm is fitted to a conventional wheel carrier version (Ø of fixing bore in wheel carrier approx. 13.5 mm), the sleeve (3h) must be installed in the wheel carrier to reduce the diameter to approx. 12.2 mm	MODEL 129, 170, 202, 208 as of 02/98 Model 210 as of 01/98, see:↓
		Install sleeve for tension arm in wheel carrier	AR35.20-P-0111-01A

Fig. item, etc.	Work instructions
Installation	Replace self-locking nuts
	Risk of death.  Death may result if vehicle slips or topples from the lifting platform.	Align vehicle between the columns of the lifting platform and position the four support plates at the lifting platform support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
3	Torque strut	Models 129, 170, 202, 208 removal: Before pulling out the hexagon bolt on the rear axle carrier, press the wheel carrier forwards - relieve the load.
		Box wrench	Figure
		Retainer wrench for counterholding torx socket bolt	Fig 3
	Diameter of wheel carrier bores modified	MODEL 129, 170, 202, 208 as of 02/98 MODEL 210 as of 01/98	BT35.20-P-0005-01A
	Bolted connection, tension arm to wheel carrier modified	MODEL 129, 170, 202, 208 as of 02/98 MODEL 210 as of 01/98	BT35.20-P-0008-01A
	The rear axle shaft must be horizontal when tightening the nuts
		Torque strut to rear axle carrier	*BA35.20-P-1001-03A
		Torque strut to wheel carrier	*BA35.20-P-1002-03A
3h	Sleeve in wheel carrier to reduce diameter	MODEL 129, 170, 202, 208 as of 02/98 Model 210 as of 01/98, see:↓
		Install sleeve for tension arm in wheel carrier	AR35.20-P-0111-01A
112c	Brake caliper dust shield without dent	Only model 202.018/020/022/023/121: To removing bolt of tension arms from wheel carrier brake caliper, push dust shield approx. 3 mm towards brake disk.

Tension arm

Number	Designation			Model 129	Model 170	Model 202	Model 208
BA35.20-P-1001-03A	Self-locking nut, tension arm to rear axle carrier	1st stage	Nm	70	70	70	70
		Step 2	∠°	-	-	-	-
BA35.20-P-1002-03A	Self-locking nut, tension arm to wheel carrier	1st stage	Nm	70	70	70	70
		Step 2	∠°	-	-	-	-
BA35.20-P-1003-03A	Bolt, tension arm to wheel carrier	1st stage	Nm	-	-	-	70
		Step 2	∠°	-	-	-	-

Tension arm

Number	Designation			Model 210 except 210.07 with Code 979 and Code Z06
BA35.20-P-1001-03A	Self-locking nut, tension arm to rear axle carrier	1st stage	Nm	70
		Step 2	∠°	-
BA35.20-P-1002-03A	Self-locking nut, tension arm to wheel carrier	1st stage	Nm	70
		Step 2	∠°	-
BA35.20-P-1003-03A	Bolt, tension arm to wheel carrier	1st stage	Nm	70
		Step 2	∠°	-

Fig 2: Identifying Ring Wrench (129 589 01 03 00)

Fig 3: Identifying Retaining Wrench (202 589 00 10 00)