Emptying and filling pressure oil system - AR32.30-P-0630A: Notes

MODEL 140 as of 1.6.94, 210 with CODE (217a) Self-levelling suspension on rear axle with ADS with CODE (480) Level control system at rear 

MODEL 202, 203.2, 208 with CODE (480) Level control system at rear 

Model 140 

Models 202, 208 

Model 203.2 

Model 210 

	Draining
	General notes for working on vehicles with level control/ADS	All models with Code 216b, 216c, 217a, 480	AH32.00-P-0002-01A
1	Detach connecting rod or connecting linkage (7) from level controller lever (arrows)
1.1	Remove linkage rod for suspension-control module/torsion bar at ball joint	Model 203.2
2	Detach torsion bar connecting rod from torsion bar	Model Series 202, 208	AR32.30-P-0630-01A
	Press torsion bar up	Improves access to drain plug in suspension-control module (3p)
3	Attach oil drain hose (061) to oil drain plug (3p) on level controller (3)	Model Series 140, 210, 203.2 at connection "S2" Model Series 202, 208 at connection "A" Note technical modifications on Model 140 with ADS ↓
	Level controller oil drain plug	Model Series 140 with ADS starting 01.10.92	BT32.30-P-9209-01A
	Risk of injury  to skin or eyes from hydraulic fluid spraying out under pressure. Risk of poisoning  from swallowing hydraulic fluid.	Release the pressure in the hydraulic system completely before starting any work on the system. Wear protective clothing and safety glasses.	AS00.00-Z-0013-01A
4	Open oil drain plug (3p) slowly and collect the oil in a clean container	The oil collected can be re-used.
	Close oil drain plug (3p) again		*BA32.30-P-1002-03A
	Refill
5	Fill reservoir (2) with fluid	Only re-use clean oil
		Funnel	Figure
		Model Series 140, 202, 203.2, 208, 210	*BF32.30-P-1001-01A
6	Push level controller lever to "Fill" position (F)
	Risk of accident.  Accidents may result if the vehicle starts off unintentionally with the engine running. Risk of injury  as working around the engine during start-up or while running may result in contusions and burns	Secure vehicle to prevent it from moving. Wear closed and snug-fitting work clothes. Do not grasp hot or rotating parts.	AS00.00-Z-0005-01A
7	Start engine and run at moderate speed for approx. 60 seconds	The system bleeds itself automatically. Installation:  Ensure that there is sufficient oil in the reservoir. The pump must never be allowed to draw in air.
	Switch off engine
8	Push level controller lever into the "Empty" (E) position.	The suspension lever must remain in this position for 60 seconds.
9.1	Connect linkage rod or relay linkage (7) to suspension-control module lever (arrows)	MODEL 140, 202, 208, 210 Replace self-locking bolts and nuts.
9.2	Connect linkage rod for suspension-control module/torsion bar at ball joint	Model 203.2
10	Place the vehicle on its wheels and push it up and down firmly several times	The vehicle level adjusts itself.
11	Check and correct oil level in oil reservoir	MODEL 140, 202, 203.2, 208	AP32.30-P-3211BA
		Model 210	AP32.30-P-3211BB

Number	Designation		Model 202 without level control	Model 202 with level control system
BA32.20-P-1001-04C	Nut, connecting rod to torsion strut	NM	30	30

Number	Designation		Model 208 without ride-height control	Model Series 208 with level control system
BA32.20-P-1001-04C	Nut, connecting rod to torsion strut	NM	30	30

Number	Designation		Model Series 203.2 with self-leveling suspension
BA32.30-P-1004-03A	Screw or nut on suspension-control module lever, suspension-control module on bracket	NM	10

Number	Designation			Model Series 140 with ride-height control/ ADS	Model 202 with level control system
BA32.30-P-1002-03A	Oil drain plug on level controller (reference value)	M10 x 1	NM	14	14

Number	Designation			Model Series 203.2 with self-leveling suspension	Model 208 with level control
BA32.30-P-1002-03A	Oil drain plug on level controller (reference value)	M10 x 1	NM	14	14

Number	Designation			Model 210 with level control / ADS
BA32.30-P-1002-03A	Oil drain plug on level controller (reference value)	M10 x 1	NM	14

Number	Designation			Model 140 with level control / ADS/ASD	Model 202 with level control /ASD
BF32.30-P-1001-01A	Filling quantity	Level control, when refilling system	Liter	≈ 2	≈ 2
		Specifications for Operating Fluids	Sheet	BB00.40-P-0343-00A	BB00.40-P-0343-00A
			Sheet	-	-

Number	Designation			Model Series 203.2 with self-leveling suspension	Model 208 with ride-height control
BF32.30-P-1001-01A	Filling quantity	Level control, when refilling system	Liter	≈ 3.5	≈ 2
		Specifications for Operating Fluids	Sheet	-	BB00.40-P-0343-00A
			Sheet	BB00.40-P-0344-00A	-

Number	Designation			Model 210 with level control system/ADS
BF32.30-P-1001-01A	Filling quantity	Level control, when refilling system	Liter	≈2
		Specifications for Operating Fluids	Sheet	-
			Sheet	BB00.40-P-0344-00A