Adjust camber and caster at the front axle - AR40.20-P-0263PW

MODEL 203.08 /09 /28 /29, 211.08 /09 /28 /29 

Camber 

Fig 1: Checking Camber - Model 203 (Except 203.081 /084 /087 /092 /281 /284 /287 /292)

Caster 

Fig 2: Checking Caster - Model 203 (Except 203.081 /084 /087 /092 /281 /284 /287 /292)

	Adjust
1.1	Remove torsion bar on front axle	Model 211	AR32.20-P-0300TW
2	Install repair bolt (19c)	Screw on nut (19b) until it abuts, but do not tighten yet so that the rubber mount of the lower transverse control arm (4) can twist when the vehicle is rocked to settle the suspension.
		Model 203	AR40.20-P-0322-01IW
		Model 211 Camber at vehicle level	AR40.20-P-0322-01VM
		Model 203	*BE40.20-P-1001-13H
		Model 211	*BE40.20-P-1003-13G
		Permissible difference in front axle camber between right and left sides of the vehicle
		Model 203	*BE40.20-P-1002-13H
		Model 211 Check caster and assign to tabular value	*BE40.20-P-1002-13G
		Model 203	AR40.20-P-0322-03P
		Model 211	AR40.20-P-0322-03T
		Permissible difference in caster between right and left sides of the vehicle	*BE40.20-P-1001-20A
		Caster	*BE40.20-P-1002-20A
3	Recheck vehicle level at front axle after adjusting the camber and caster.	The vehicle level must correlate with the dimension established on the initial measurement.
		Model 203	AR40.20-P-0301P
		Model 211	AR40.20-P-0301T
4	Tighten nut (19b)	The repair bolt (19c) must not be turned after fixing. When tightening the nut (19b) counterhold the repair bolt (19c) otherwise the lock tabs in the rubber mount of the lower transverse control arm (4) will be sheared off. Model 203
		Model 211	*BA33.20-P-1008-01E
			*BA33.20-P-1010-01A
5.1	Install stabilizer bar on the front axle	Model 211	AR32.20-P-0300TW

INSPECTION AND ADJUSTING VALUES FOR FRONT-AXLE CAMBER

Number	Designation		Model 203 with 4MATIC
BE40.20-P-1001-13H	Camber at vehicle level	+5.1°	-0° 04' (± 20')
		+4.8°	-0° 04' (±20')
		+4.5°	-0° 07' (±20')
		+4.2°	-0° 08' (±20')
		+3.9°	-0° 10' (±20')
		+3.6°	-0° 12' (±20')
		+3.3°	-0° 14' (±20')
		+3.1°	-0° 15' (±20')
		+2.8°	-0° 17' (±20')
		+2.5°	-0° 18' (±20')
		+2.2°	-0° 20' (±20')
		+1.9°	-0° 22' (±20')
BE40.20-P-1002-13H	Permissible difference in front axle camber between right and left sides of the vehicle	∠ °	≤20'

CHECK VALUES FOR FRONT AXLE CAMBER

Number	Designation			Model 211.08/09/28/29
BE40.20-P-1002-13G	Permissible difference in front axle camber between right and left sides of the vehicle		∠ °	20'
BE40.20-P-1003-13G	Camber at vehicle level	+7.9°	∠ °	-0° (± 10'/-30')
		+7.2°	∠ °	-0° 10' (± 10'/-30')
		+6.5°	∠ °	-0° 15' (± 10'/-30')
		+5.8°	∠ °	-0° 23' (± 10'/-30')
		+5.1°	∠ °	-0° 30' (± 10'/-30')
		+4.4°	∠ °	-0° 36' (± 10'/-30')
		+3.7°	∠ °	-0° 43' (± 10'/-30')
		+3.0°	∠ °	-0° 48' (± 10'/-30')
		+2.3°	∠ °	-0° 54' (± 10'/-30')
		+1.6°	∠ °	-1° 00' (± 10'/-30')
		+0.9°	∠ °	-1° 06' (± 10'/-30')
		+0.2°	∠ °	-1° 10' (± 10'/-30')
		-0.5°	∠ °	-1° 15' (± 10'/-30')
		-1.2°	∠ °	-1° 19' (± 10'/-30')

CHECK AND ADJUSTMENT VALUES FOR CASTER

Number	Designation		Model 203	Model 211
BE40.20-P-1001-20A	Permissible difference in caster between right and left sides of the vehicle	∠ °	30'	30'
BE40.20-P-1002-20A	Caster	See table	AR40.20-P-0322-03P	AR40.20-P-0322-03T

WHEEL LOCATION, HUB

Number	Designation		Models 203.081/084/087/092/281/284/287/292
BA33.20-P-1008-01E	Self-locking nut, transverse control arm to frame	Nm	110

WHEEL LOCATION, HUB

Number	Designation		Model 211.08/09/28/29
BA33.20-P-1010-01A	Self-locking nut, lower wishbone to front axle carrier	Nm	110