Check quiescent current consumption - AR54.10-P-1030P

MODEL 203, 209, 463.243 /244 /245 /246 /247 /248 /249 /250 /254 /309 /322 /323 /332 /333 

Shows model 463.249 

Fig 1: Identifying Cup Holder And Battery Box Lid - Shows Model 463.249

	Checking
	Risk of explosion  caused by oxyhydrogen gas. Risk of poisoning and caustic burns  caused by swallowing battery acid. Risk of injury  caused by burns to skin and eyes from battery acid or when handling damaged lead-acid batteries	No fire, sparks, open flames or smoking. Wear acid-resistant gloves, clothing and glasses. Only pour battery acid into suitable and appropriately marked containers.	AS54.10-Z-0001-01A
	Notes on battery	All models	AH54.10-P-0001-01A
1.1	Remove dust filter housing for heating/ventilation	Model 203, 209.
			AP83.00-P-8381P
1.2	Remove cup holder (A)	Model 463.246 /249
1.3	Remove battery box cover (B)
2.1	Preparing test with quiescent current retention unit		AR54.10-P-1030-01P
		Multimeter	*WH58.30-Z-1001-09A
		Quiescent current retention unit CMP 12.2	*WH58.30-Z-1012-09A
2.2	Prepare test without quiescent current retention unit		AR54.10-P-1030-02P
		Multimeter	*WH58.30-Z-1001-09A
3	Switch off all consumers	Remove transmitter/ignition key. Switch off stationary heater. Switch off car phone. Switch off radio. Switch off interior protection. Switch off vanity mirror Switch off reading light. Turn rotary light switch to "0" position. Close doors, the interior illumination must go out automatically after a few seconds. With Comand: Remove CD-ROM from Comand, switch off Comand.
	Risk of injury  to skin and eyes caused by handling hot or glowing objects.	Wear safety gloves, protective clothing and safety glasses, if necessary.	AS00.00-Z-0002-01A
4	Check whether auxiliary water pump is operating	Carefully touch coolant hose or additional water pump Auxiliary water pump operating:↓ Do not commence quiescent current test until pump has switched off.
5.1	Remove cover below instrument panel (right)	Model 463.243 /244 /245 /246 /247 /248/ 249 /250 /254 /309 /322 /323 /332 /333. Do not disconnect any electrical couplings.	AR68.10-P-1520GM
6	Testing quiescent current		AR54.10-P-1030-03P
		Baseline current draw test adapter 1	Figure
		Quiescent current test adapter 2	Figure
		Multimeter	*WH58.30-Z-1001-09A
		If specification for total quiescent current is not achieved: ↓
		Determine circuit with excessive quiescent current consumption.	AR54.10-P-1030-04P
		Specification not achieved: ↓ Determine fuse-protected components with increased quiescent current consumption.	AR54.10-P-1030-05P
		Specification not achieved: ↓ Determine non-fuse protected components with increased quiescent current consumption.	AR54.10-P-1030-06P
		To check, re-test quiescent current.	AR54.10-P-1030-03P
7	Render electrical system operational	Only if no quiescent current retention device has been used. See: ↓
		Perform basic programming.	AR00.19-P-0200P

Fig 2: Identifying Quiescent Current Test Adapter 1 (140 589 12 21 00)

Fig 3: Identifying Quiescent Current Test Adapter 2 (140 589 13 21 00)