Remove/install camber strut - AR35.20-P-0110B: Notes

MODELS 129, 170, 202, 208, 210 

Shown on model 210 

Fig 1: Identifying Camber Strut Remove/Install Components

Modification notes

28.2.98	Diameter of wheel carrier bores modified	Model 129, 170, 202, 208 as of 02/98 Model 210 as of 01/98	BT35.20-P-0005-01A
28.2.98	Bolted connection, camber strut to wheel carrier modified	Tightening torque of bolted connection M10 increased from 45 Nm to 70 Nm  for new bolted connection M12  .	BT35.20-P-0007-01A
28.2.98	If a new camber strut is fitted to a conventional wheel carrier version (ø of fixing bore in wheel carrier approx. 13.5 mm), the sleeve (2h) must be installed in the wheel carrier to reduce the diameter to approx. 12.2 mm	Model 129, 170, 202, 208 as of 02/98 Model 210 as of 01/98, see:↓
		Install sleeve for camber strut in wheel carrier	AR35.20-P-0110-02A

Fig. item, etc.	Work instructions
Installation	Replace self-locking nuts and bolts
	Risk of death.  Death may result if vehicle slips or topples from the lifting platform.	Align vehicle between the columns of the lifting platform and position the four support plates at the lifting platform support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
	Assembly attachment		Figure
1c, 1d	Rear axle mount bolt, front and rear	Only model 210 removal: If the direction of installation of the bolt (2a) is from the front, the front and rear axle mount bolt (1c, 1d) is not detached. Installation:  recut thread on frame floor with tap.
		Front rear axle mount bolt.	*BA35.10-P-1001-01A
		rear axle mount bolt	*BA35.10-P-1002-01A
2	Camber strut	Box wrench	Fig 2
	Diameter of wheel carrier bores modified	Model 129, 170, 202, 208 as of 02/98 Model 210 as of 01/98	BT35.20-P-0005-01A
	Bolted connection, camber strut to wheel carrier modified	Model 129, 170, 202, 208 as of 02/98 Model 210 as of 01/98	BT35.20-P-0007-01A
		The rear axle shaft must be horizontal when tightening the nuts.
		Camber strut to rear axle carrier	*BA35.20-P-1001-02A
		Camber strut to wheel carrier	*BA35.20-P-1002-02A
2H	Sleeve in wheel carrier to reduce diameter	Model 129, 170, 202, 208 as of 02/98 Model 210 as of 01/98, see:↓
		Install sleeve for camber strut in wheel carrier	AR35.20-P-0110-02A

Rear axle carrier

Number	Designation				Model 210
BA35.10-P-1001-01A	Self-locking bolt, front rear axle carrier rubber mount to frame floor			Nm	90
		with bolt	1st stage	Nm	-
		flange ø 24 mm	2nd stage	∠°	-
		with bolt	1st stage	Nm	-
		Flange ø 26 mm	2nd stage	∠°	-
BA35.10-P-1002-01A	Self-locking bolt, rear axle carrier rear rubber mount to frame floor			Nm	90
		with bolt	1st stage	Nm	-
		flange ø 24 mm	2nd stage	∠°	-
		with bolt	1st stage	Nm	-
		Flange ø 26 mm	2nd stage	∠°	-

Camber strut

Number	Designation			Model 129	Model 170	Model 202	Model 208
BA35.20-P-1001-02A	Self-locking nut, camber strut to rear axle carrier.	1st stage	Nm	70	70	70	70
		2nd stage	∠°	-	-	-	-
BA35.20-P-1002-02A	Self-locking nut, camber strut to wheel carrier.	M10	Nm	40	40	40	40
		M12	Nm	70	70	70	70

Camber strut

Number	Designation			Model Series 210 except 210.07 with code 979 and code Z06
BA35.20-P-1001-02A	Self-locking nut, camber strut to rear axle carrier.	1st stage	Nm	70
		2nd stage	∠°	-
BA35.20-P-1002-02A	Self-locking nut, camber strut to wheel carrier.	M10	Nm	40
		M12	Nm	70

Fig 2: Identifying Ring Wrench (129 589 01 03 00)

Fig 3: Identifying Assembly Attachment (140 589 01 62 00)