Retrofit DVD player wiring harness - AZ82.60-P-0005-02MA

MODEL 220 as of 1.9.02 

The connection line for the AV signals (12) is only required when the TV tuner is installed with an AMP plug.

Fig 1: Identifying DVD Player Wiring Harness

1. Route wiring harness in vehicle as shown in figure.
   Fig 2: Identifying Route Wiring Harness In Vehicle

   
2. Route DVD player wiring harness (10) to COMAND operating, display and control module (A40/3).
3. Wind felt strip around filter box and fasten in place (see arrow).
4. Route black (sw) lead from DVD player wiring harness (10) to ashtray housing.
   Fig 3: Identifying DVD Player Wiring Harness

   
   Fig 4: Identifying DVD Player Wiring Harness And Control Module

   
5. Detach connection coupling (A) of COMAND operating, display and control module (A40/3) an undo wiring harness by 50 mm.
6. Connect brown line (br) from chamber 8 (circuit 31) of connection coupling (A) with brown line (br) from DVD player (A40/4) using soldering iron.
7. Connect red/yellow line (rt/ge) from chamber 4 (circuit 30) of connection coupling (A) with red line (rt) from DVD player (A40/4) using soldering iron.
   Fig 5: Identifying Connection Coupling And Control Module

   
8. Untie wiring harness 50 mm back at connector for ashtray housing.
9. Connect black/gray line (sw/gr) of ashtray housing connector with black line (sw) of DVD player (A40/4) using soldering iron.
   Fig 6: Identifying Wiring Harness

   
10. Route TV signal extension line (12a) to footwell along A-pillar.
11. Route infrared sensor line (11) along A-pillar and fasten in place using felt strip.
    Fig 7: Identifying Infrared Sensor Line

    
12. Wind felt strip around infrared sensor line (11) and route under the roofliner to the overhead control panel.
13. Insert infrared sensor (see arrow) as shown in figure template into gap on switch of left reading lamp and push all the way down.
    Fig 8: Identifying Infrared Sensor Line And Overhead Control Panel Control Module

    
    Fig 9: Identifying Infrared Sensor Line

    
14. Fasten infrared sensor line (11) using felt strip to rear side of overhead control panel control module (N70).
15. Remove cutout for reading lamp switch in covering on right-hand side (see arrow) for IR sensor approx.
    Fig 10: Locating Cutout Area Of Reading Lamp Switch

    
    Fig 11: Identifying Infrared Sensor Line And Overhead Control Panel Control Module

    
16. Route the extension line for the AV signals (12a), starting at the DVD player (A40/4), up to the installation location of the TV tuner (A2/42).

    The extension line for the AV signals (12a) must be routed between the floor lining and the side sill to the cable duct in the trunk and then along the rear shelf and fastened in place using felt strips.

17. Connect the red (rt) and white (ws) plugs of the extension line for the AV signal (12a) to the red (rt) and black (sw) socket of the AF interference suppression filter (12c).
    Fig 12: Identifying Extension Line For AV Signals, DVD Player And TV Tuner

    
18. Insert the red and black plugs from the AF interference suppression filter output (12c) and the yellow plug of the extension line to the AV signal (12a) into the color-coded cinch socket (see fig.) of TV tuner (A2/42).

    Insert the black plug from the AF interference suppression filter in the white cinch socket of the TV tuner (A2/42).

    Fig 13: Identifying AF Interference Suppression Filter, AV Signal And TV Tuner

    
19. Tie the AF interference suppression filter (12c) together with the extension line for the AV signal (12a) and fasten to existing wiring harnesses.
    Fig 14: Identifying AF Interference Suppression Filter And AV Signal