Carry out distance and comparison measurements on rear axle - AR40.30-P-0402-02I

TEST VALUES FOR DISTANCE AND COMPARISON MEASUREMENTS ON REAR AXLE

Number	Designation			Model 215	Model 220
BE40.30-P-1001-05B	Dimension	H1	mm	4	4
		H2	mm	3	3
		H4	mm	4	4
		H5	mm	6	6
		H6	mm	1096 (± 2)	1096 (± 2)
		H7	mm	1085 (± 2)	1085 (± 2)
		H8	mm	3	3
		H9	mm	3	3
		See picture in		AR40.30-P-0402-02N	AR40.30-P-0402-02I

Fig 1: Identifying Telescopic Measuring Rod (124 589 01 19 00)

Fig 2: Identifying Telescopic Measuring Rod (124 589 02 19 00)

Fig 3: Identifying Mount (170 589 00 63 00)

Fig 4: Identifying Set Of Measurement Fixtures (140 589 09 63 00)

Fig 5: Identifying Connecting Pieces (124 589 08 63 00)

The measuring points are shown on model 220 with AIRmatic

Comparison dimension "H1 " measured from the check bore "K " to the tie rod support on the wheel carrier left to right.
Use telescopic measuring rod (06) 124 589 02 19 00 with measuring tips (024c) 140 589 09 63 02.

Fig 6: Identifying Dimension H1 And Telescopic Measuring Rod
Comparison dimension "H2 " measured from the check bore "K " to the center of the torx bolt head of the front bearing of the rear axle carrier left to right. Unscrew, screw in torx bolts if necessary and check for bending.
Use telescopic measuring rod (06) 124 589 02 19 00 with measuring tips (024c) 140 589 09 63 04. Measured to the center of the Torx bolt head.

Fig 7: Identifying Dimension H2
Comparison dimension "H4 " measured from the check bore "K " to the center of the hexagon bolt of the front thrust arm on the rear axle carrier left to right.
Use telescopic measuring rod (06) 124 589 02 19 00 with measuring tips (024d) 140 589 09 63 03.

Fig 8: Identifying Dimension H4
Comparison dimension "H5 " measured from the check bore "K " to the center of the torx bolt head of the rear bearing of the rear axle carrier left to right. Unscrew, screw in torx bolts if necessary and check for bending.
Use telescopic measuring rod (06) 124 589 02 19 00 with measuring tips (024d) 140 589 09 63 03.

Fig 9: Identifying Dimension H5
Distance dimension "H6 " measured to the center of the torx bolt heads between the front bearings of the rear axle carrier.
Use telescopic measuring rod (06) 124 589 02 19 00 with measuring bolts (024h) 140 589 09 63 04 and (024d) 140 589 09 63 03 combined.

Fig 10: Identifying Dimension H6
Distance "H7 " measured to the centers of the torx bolt heads between the rear mountings of the rear axle carrier.
Use telescopic measuring rod (06) 124 589 02 19 00 with measuring bolts (024h) 140 589 09 63 04 and (024d) 140 589 09 63 03 combined.

Fig 11: Identifying Dimension H7
Distance dimension "H8 " measured to the center of the torx bolt heads between the front and rear bearing of the rear axle carrier.
Use telescopic measuring rod (06) 124 589 01 19 00 with measuring bolts (024h) 140 589 09 63 04 and (024d) 140 589 09 63 03 combined.

Fig 12: Identifying Dimension H8
Comparison measurement "H9 " measured diagonally from left to right to the centers of the torx bolt heads between the front and rear mountings of the rear axle carrier.
Use telescopic measuring rod (06) 124 589 02 19 00 with measuring bolts (024h) 140 589 09 63 04 and (024d) 140 589 09 63 03 combined.

Fig 13: Identifying Dimension H9