LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2001 >> CLK320 2D Convertible >> Repair and Diagnosis >> Suspension >> Wheels & Tire System >> Wheels, Chassis Alignment Check -- 208 Chassis >> Testing & Repair >> Measuring spring link, camber arm, radius rod, thrust arm and track rod of rear axle - AR40.30-P-0420A

Measuring spring link, camber arm, radius rod, thrust arm and track rod of rear axle - AR40.30-P-0420A

MODEL 129, 170, 171, 202, 203, 209.3 /4, 208, 210 

Fig 1: Measuring Spring Link, Camber Arm, Radius Rod, Thrust Arm And Track Rod Of Rear Axle
G04624908
INSPECT Check     
DANGER Risk of death  cased by vehicle slipping or toppling off of the lifting platform. Align vehicle between the columns of the hydraulic hoist and position the four support plates below the hoist support points specified by the vehicle manufacturer. AS00.00-Z-0010-01
1 Carry out visual inspection IMPORTANT Check individual parts for damage, corrosion and wear  
MEASURING Measuring camber strut     
2 Remove camber strut (2) Model 129, 170, 202, 208, 210 AR35.20-P-0110B
    Model 171 AR35.20-P-0110V
    Model 203, 209 AR35.20-P-0110P
3 Insert measuring pins (041a, 041b)    
REFER TO SHOP-MADE TOOLS Measuring pin for rear-axle wheel control   WF58.50-P-4030-01A
4 Measure dimension (L1) on both sides   *BE40.30-P-1001-03A 
    COMMERCIALLY AVAILABLE TOOLS Measuring caliper *WH58.30-Z-1006-12A 
5 Remove measuring pins (041a, 041b)    
REFER TO SHOP-MADE TOOLS Measuring pin for rear-axle wheel control   WF58.50-P-4030-01A
6 Install camber strut (2) Model 129, 170, 202, 208, 210 AR35.20-P-0110B
    Model 171 AR35.20-P-0110V
    Model 203, 209 AR35.20-P-0110P
MEASURING Measuring tension arm     
7 Remove torque strut (3) Model 129, 170, 202, 208, 210 AR35.20-P-0111B
    Model 171 AR35.20-P-0111V
    Model 203, 209 AR35.20-P-0111P
8 Insert measuring pins (041b, 041c)    
REFER TO SHOP-MADE TOOLS Measuring pin for rear-axle wheel control   WF58.50-P-4030-01A
9 Measure dimension (L4) on both sides   *BE40.30-P-1001-03A 
    COMMERCIALLY AVAILABLE TOOLS Measuring caliper *WH58.30-Z-1006-12A 
10 Remove measuring pins (041b, 041c)    
REFER TO SHOP-MADE TOOLS Measuring pin for rear-axle wheel control   WF58.50-P-4030-01A
11 Install torque strut (3) Model 129, 170, 202, 208, 210 AR35.20-P-0111B
    Model 171 AR35.20-P-0111V
    Model 203, 209 AR35.20-P-0111P
MEASURING Measuring track rod     
12 Remove tie rod (4) Model 129, 170, 202, 208, 210 AR35.20-P-0112B
    Model 171 AR35.20-P-0109V
    Model 203, 209 AR35.20-P-0112P
13 Insert measuring pin (041b). IMPORTANT Mark center point of tie rod end.  
REFER TO SHOP-MADE TOOLS Measuring pin for rear-axle wheel control   WF58.50-P-4030-01A
14 Measure dimension (L3)   *BE40.30-P-1001-03A 
    COMMERCIALLY AVAILABLE TOOLS Caliper gage, measuring range up to 400 mm *WH58.30-Z-1006-12A 
15 Remove measuring pin (041b).    
REFER TO SHOP-MADE TOOLS Measuring pin for rear-axle wheel control   WF58.50-P-4030-01A
16 Install tie rod (4) Model 129, 170, 202, 208, 210 AR35.20-P-0112B
    Model 171 AR35.20-P-0109V
    Model 203, 209 AR35.20-P-0112P
MEASURING Measuring torque strut     
17 Remove thrust arm (5) Model 129, 170, 202, 208, 210 AR35.20-P-0113B
    Model 171 AR35.20-P-0113V
    Model 203, 209 AR35.20-P-0113P
18 Insert measuring pins (041b, 041c)    
REFER TO SHOP-MADE TOOLS Measuring pin for rear-axle wheel control   WF58.50-P-4030-01A
19 Measure dimension (L2) on both sides   *BE40.30-P-1001-03A 
    COMMERCIALLY AVAILABLE TOOLS Caliper gage, measuring range up to 400 mm *WH58.30-Z-1006-12A 
20 Remove measuring pins (041b, 041c)    
REFER TO SHOP-MADE TOOLS Measuring pin for rear-axle wheel control   WF58.50-P-4030-01A
21 Install thrust arm (5) Model 129, 170, 202, 208, 210 AR35.20-P-0113B
    Model 171 AR35.20-P-0113V
    Model 203, 209 AR35.20-P-0113P
MEASURING Measuring spring link     
22 Remove spring link (6) Model 129, 170, 202, 208, 210 AR35.20-P-0114B
    Model 171 AR35.20-P-0119V
    Model 203, 209 AR35.20-P-0114P
23 Insert measuring pins (041d, 041e)    
REFER TO SHOP-MADE TOOLS Measuring pin for rear-axle wheel control   WF58.50-P-4030-01A
24 Measure dimension (L5) on both sides   *BE40.30-P-1001-03A 
    SPECIAL TOOL Telescopic measuring rod Figure
25 Remove measuring pins (041d, 041e)    
REFER TO SHOP-MADE TOOLS Measuring pin for rear-axle wheel control   WF58.50-P-4030-01A
26 Install spring link (6) Model 129, 170, 202, 208, 210 AR35.20-P-0114B
    Model 171 AR35.20-P-0119V
    Model 203, 209 AR35.20-P-0114P
TEST VALUES FOR TORQUE STRUT/TENSION ARM/CAMBER STRUT, SPRING LINK, TRACK ROD ON REAR AXLE

Number Designation Model 129 Model 170 Model 171 Model 202
BE40.30-P-1001-03A Dim. Camber strut "L1" mm 298,5 ± 0,5 298,5 ± 0,5 298.5 (± 0.5) 298,5 ± 0,5
Torque strut "L2" mm 314,5 ± 0,5 314,5 ± 0,5 314.5 (± 0.5) 314,5 ± 0,5
Track rod "L3" mm 245 ± 0,5 245 ± 0,5 257 (± 0.5) 245 ± 0,5
Tension arm "L4" mm 247 ± 0,3 247 ± 0,3 247 (± 0.3) 247 ± 0,3
Spring link "L5" mm 466,1 ± 0,5 466,1 ± 0,5 466.1 (± 0.5) 466,1 ± 0,5
For picture, see AR40.30-P-0420A  AR40.30-P-0420A  AR40.30-P-0420A  AR40.30-P-0420A 
TEST VALUES FOR TORQUE STRUT/TENSION ARM/CAMBER STRUT, SPRING LINK, TRACK ROD ON REAR AXLE

Number Designation Model 203 Model 208 Model 209 Model 210
BE40.30-P-1001-03A Dim. Camber strut "L1" mm 298.5 (± 0.5 298,5 ± 0.5 298.5 (± 0,5 298,5 ± 0.5
Torque strut "L2" mm 314.5 (± 0.5) 314,5 ± 0,5 314.5 (± 0.5) 314,5 ± 0,5
Track rod "L3" mm 257 (± 0.5) 245 ± 0,5 257 (± 0,5) 245 ± 0,5
Tension arm "L4" mm 247 (± 0.3) 247 0,3 247 (± 0.3) 247 ± 0,3
Spring link "L5" mm 466.1 (± 0.5) 466,1 ± 0,5 466.1 (± 0.5) 466,1 ± 0,5
For picture, see AR40.30-P-0420A  AR40.30-P-0420A  AR40.30-P-0420A  AR40.30-P-0420A 
Fig 2: Identifying Telescopic Measuring Rod (124 589 01 19 00))
G04624909
COMMERCIALLY AVAILABLE TOOLS

Number Designation
WH58.30-Z-1006-12A Caliper gauge
scientia non olet · About LEMON Manuals