Dialing, function - GF82.70-P-3000M

MODELS 215.3, 220.0 /1 as of 1.9.03 with CODE (813) Voice control system (VCS) 

Function 

After activating the system, the user has a number of options for establishing a desired connection by using the following commands for editing.

However, the user has to take into consideration whether the card is inserted, the PIN is entered, the network is available, and the telephone is ready.

User editing commands for stored or non-stored numbers:

• Dial telephone number
• Dial number
• Dial name
• Read telephone book

User final commands:

• Dial
• Store

After activation has been completed and the user has spoken the editing command, e.g. "Dial number" or "Dial telephone number", the voice control system (VCS) requests the user to enter a telephone number by the voice output saying "Please say number".

If an error occurs when entering the desired telephone number, e.g., improper recognition of a number by the VCS or incorrect entry by the user, it is possible for the user to delete or correct the number. If the number was entered without errors and recognized correctly by the VCS, the final command "Dial" given by the user is confirmed by the VCS announcement "The number is being dialed" and the connection is established. If the user would like to have the desired phone number permanently available after entering it successfully, then instead of the final command "Dial" the final command "Store" must be spoken. Thereupon the VCS requests the user to enter the desired name through the spoken announcement "Please say the name". After this has been entered by the user, the VCS requests the user to repeat the name as confirmation. Then the number and the associated name are stored in the telephone book, indicated by the spoken announcement "Name and number have been stored".

The entries stored in the telephone book can only be called up reliably by the users who store them.

"Dialing a name" entry:

• The editing command "dial name" can be used to request a name that is already stored in the telephone book. To this end, the VCS requests the user to say the desired name

"Listening to the telephone book" entry:

• The editing command "Read telephone book" can be selected to have the telephone book read out by the VCS, in order to press the VCS switch (S93/2) when the desired name is being read out. With this command it is therefore possible to "scroll" through the telephone book.

The editing command "Read telephone book" can also be used when the VCS has difficulty in recognizing a name entered by the user using voice input.

If it is already in the telephone book, the name can then be selected and thus the connection established.

With the two dialing options listed here, the final command "Dial" is not needed.

After the name has been repeated by the VCS, the user is informed by the voice output feature that the "number is being dialed" and that the call is completed.

If, with the dialing options listed, the desired number is not available (e.g., the desired connection is busy), the user then has the option of redialing the number dialed last after terminating the dialing procedure and reactivating the VCS with the editing command "Redial".

During the particular dialing options, it is possible at any time to terminate the dialog with the VCS either by pressing the VCS switch (S93/2) or spoken input "Terminate" by the user.

Deleting or correcting digits during the number entry 

If the VCS system has performed a faulty recognition or the user has made a wrong entry, then this number can be corrected using 3 methods.

• Delete
• Delete number
• Delete telephone number

This means that all the numbers previously entered are deleted, the system informs the user of this via the spoken announcement "The number is deleted, please say it" and other numbers or commands are requested for the entry.

It is also possible to make calls abroad using the VCS. In addition to this, it is also possible to control announcement services or to operate the mailbox.

The VCS has a help function to make operation as simple as possible. The user is in Dialog mode with the telephone and says the word "Help", the VCS reads the most important telephone commands aloud.

If the user is in dialog with the COMAND operating, display and control unit (A40/3), then he/she can say "Help phone" whereupon the system is changed and the VCS reads out the most important phone commands.

	Hands-free microphone, location/task		GF82.70-P-4102M
	Hands-free system loudspeaker, location/task		GF82.70-P-4103M