Retrofit DVD player wiring harness - AZ82.60-P-0005-02M

MODEL 220 up to 31.8.02 

Fig 1: Identifying DVD Player Wiring Harness

1. Route wiring harness in vehicle as shown in figure.
   Fig 2: Identifying Route Wiring Harness In Vehicle

   
2. Route DVD player wiring harness (10) to COMAND operating, display and control module (A40/3).
3. Wind felt strip around filter box and fasten in place (see arrow).
4. Route black (sw) lead from DVD player wiring harness (10) to ashtray housing.
   Fig 3: Identifying DVD Player Wiring Harness

   
   Fig 4: Identifying DVD Player Wiring Harness And Control Module

   
5. Detach connection coupling (A) of COMAND operating, display and control module (A40/3) and undo wiring harness by 50 mm.
6. Connect brown line (br) from chamber 8 (circuit 31) of connection coupling (A) with brown line (br) from DVD player (A40/4) using soldering iron.
7. Connect red/yellow line (rt/ge) from chamber 4 (circuit 30) of connection coupling (A) with red line (rt) from DVD player (A40/4) using soldering iron.
   Fig 5: Identifying Connection Coupling And Control Module

   
8. Untie wiring harness 50 mm back at connector for ashtray housing.
9. Connect black/gray line (sw/gr) of ashtray housing connector with black line (sw) of DVD player (A40/4) using soldering iron.
   Fig 6: Identifying Wiring Harness

   
10. Route TV signal extension line (12a) to footwell along A-pillar.
11. Route infrared sensor line (11) along A-pillar and fasten in place using felt strip.
    Fig 7: Identifying Infrared Sensor Line

    
12. Wind felt strip around infrared sensor line (11) and route under the roofliner to the overhead control panel.
13. Insert infrared sensor (see arrow) as shown in figure template into gap on switch of left reading lamp and push all the way down.
    Fig 8: Identifying Infrared Sensor Line And Overhead Control Panel Control Module

    
14. Fasten infrared sensor line (11) using felt strip to rear side of overhead control panel control module (N70).
15. Remove cutout for reading lamp switch in covering on right-hand side (see arrow) for IR sensor approx.
    Fig 9: Locating Cutout Area Of Reading Lamp Switch

    
    Fig 10: Identifying Infrared Sensor Line And Overhead Control Panel Control Module

    
16. Route the extension line for the AV signals (12a), starting at the DVD player (A40/4), up to the installation location of the TV tuner (A2/42).

    The extension line for the AV signals (12a) must be routed between the floor lining and the side sill to the cable duct in the trunk and then along the rear shelf and fastened in place using felt strips.

17. Route the connection line for the AV signals (12) through the crinkled foamed material to the extension line for the AV signals (12a).
18. Connect the AF interference suppression filter (12c) between the red and black AV signal lines (12, 12a) and fasten each of the couplings in place using felt strip.
    Fig 11: Identifying Extension Line For AV Signals, DVD Player And TV Tuner

    
19. Connect the two yellow couplings of the AV signal lines (12, 12a) straight to each other and also fasten in place using felt strip.
20. Insert the 18-pin black coupling into the plug position (AV1) of the TV tuner (A2/42).

    The plug position is coded.

Fig 12: Identifying Plug Position And TV Tuner

21. Tie the AF interference suppression filter (12c) together with the AV signal lines (12, 12a) and fasten to existing wiring harnesses.
    Fig 13: Identifying AF Interference Suppression Filter And AV Signal Lines