Remove/install engine mount - AR22.10-P-1100PW

ENGINE 112 in MODEL 203.081 /084 /281 /284

ENGINE 272.970 in MODEL 203.087 /287

ENGINE 272.941 in MODEL 203.092 /292

Shown for right engine mount

Fig 1: Identifying Engine Mount And Support - Shown For Right Engine Mount

Fig 2: Identifying Engine Mount And Front Axle Carrier - Shown For Right Engine Mount

Fig 3: Identifying Engine Mount, Support, Anti-Twist Lock And Retaining Groove - Shown For Right Engine Mount

	Remove
	Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.	When moving components, ensure that no body parts or limbs are within the operating range of moving parts.	AS00.00-Z-0011-01A
	Risk of death caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between the columns of the lifting platform and position the four support plates at the lifting platform support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
	Notes on self-locking nuts and bolts		AH00.00-N-0001-01A
1	Open engine hood		AR88.40-P-1000P
2	Remove engine suction fan ducts in front of air filter
3.1	Detach from above air filter vertically from the cylinder head covers.	Model 203.081 /084 /281 /284
3.2	Remove air filter housing	Model 203.087 /092 /287 /292	AR09.10-P-1150QB
4	Put on engine support bracket		AR33.10-P-0100-01P
		Engine supporting shackle	*WH58.30-Z-1002-07A
5	Remove upper engine mount (1) from engine support (2)
6	Lift the engine slightly
7	Raise vehicle.		AR00.60-P-1000P
8	Take off bottom engine compartment panel at front		AR61.20-P-1105P
9	Detach the lower engine mount (1) from the front axle carrier (3)
10	Remove the engine mount (1) to the outside between the front axle carrier (3) and the body	Observe the environmental protection regulations for the disposal of engine mounts. Dispose engine mounts into mixed scrap.
	Install
11	Install the upper engine mount (1) at the engine support (2)	The anti-twist lock (a) at the engine mount (1) mist sit in the retaining groove (b) in the engine support (2)
		Model 203.081 /084 /281 /284	*BA22.10-P-1004-01R
		Model 203.087 /092 /287 /292	*BA22.10-P-1002-01S
12	Lower engine
13	Install the lower engine mount (1) at the front axle carrier (3)	The engine mount (1) must sit in the raised portions at the front axle carrier (3).
		Model 203.081 /084 /281 /284	*BA22.10-P-1001-01R
		Model 203.087 /092 /287 /292	*BA22.10-P-1001-01S
14	Fit on lower engine compartment panel at front		AR61.20-P-1105P
15	Remove engine support rack
16.1	Install air filter housing	Model 203.081 /084 /281 /284 Lightly coat the rubber retainers with anti-friction agent on the cylinder head covers and the sealing ring of the hot film mass air flow sensor (B2/5) in the air filter housing.
		Lubricant	*BR00.45-Z-1002-06A
16.2	Install air filter housing	Model 203.087 /092 /287 /292	AR09.10-P-1150QB
		Lubricant	*BR00.45-Z-1002-06A
17	Install engine suction fan ducts in front of air filter
18	Close engine hood		AR88.40-P-1000P

ENGINE MOUNTS, ENGINE SUPPORTS

Number	Designation		Engine 112.916/ 953 in model 203
BA22.10-P-1001-01R	Bolt connecting front engine mounts to front axle carrier	Nm	35
BA22.10-P-1004-01R	Bolt connecting front engine mount to engine support	Nm	50

ENGINE SUSPENSION, ENGINE MOUNTS, ENGINE SUPPORTS

Number	Designation		Engine 272 in model 203 with 4-MATIC
BA22.10-P-1001-01S	Bolt connecting front engine mounts to front axle carrier	Nm	35
BA22.10-P-1002-01S	Bolt connecting front engine mount to engine support	Nm	50

COMMERCIALLY AVAILABLE TOOLS

Number	Designation
WH58.30-Z-1002-07A	Engine carrier arm

REPAIR MATERIALS

Number	Designation	Order number
BR00.45-Z-1002-06A	Lubricant	A 000 989 01 60