Carrying out start-up and function check - AZ82.61-P-0001-04A

Models 129, 140, 163, 168, 170, 202, 208, 210 

System description 

Fig 1: Identifying Trafficstar Display Field, Automatic Button And Mode Button

Step 5 for initial start-up only applies for equipment which has already been installed in a vehicle and on which initial calibration has been performed.

	Start-up step	Entry with TrafficStar keys	Feedback on TrafficStar display field
1	Start engine
2	Switch on TrafficStar	Enter code (see CODE card) with multifunction buttons below the numbers on the display field.	CODE 1 2 3 4 5 6 7 8
3	Insert navigation CD into TrafficStar	Loading time approx. 1 min.
4	Activate service mode	Press mode button (M) repeatedly until NAVIGATE  appears	NAVIGATE
		Press automatic button (A) repeatedly until CONFIG  appears	CONFIG 1 2 3 4 5 6 7 8*
		Confirm CONFIG  with multifunction button below (*)	SYSTEM 1 2 3 4 5 6 7 8*
		Confirm SYSTEM  with multifunction button (GHI) and (MNO)	MODULE *
5	Erase initial calibration	Applies only when initial calibration has been performed on the unit
		Press automatic button (A) repeatedly until NEW CAL  appears	NEW CAL *
		Confirm NEW CAL  with multifunction button below (*)	CAUTION CALIBRATION WILL BE ERASED
		Hold multifunction button below (*) depressed until the following message appears Initial calibration is then erased and the unit can be recalibrated.	CALIBRATION ERASED
		Press multifunction button (←)	NEW CAL *
		Press automatic button (A) repeatedly until MODUL T  appears	MODULE T *
6	Perform module test	Confirm MODUL T  with multifunction button below (*) Press multifunction button (←)	MODULE OK  MODULE T *
7	Perform voice test	Press automatic button (A) repeatedly until VOICE T  appears	VOICE T *
		Confirm VOICE T  with multifunction button below (*)	Voice output
		The unit switches automatically to service mode	Voice T *
8	GAL test	Press automatic button (A) repeatedly until GAL TEST  appears	GAL TEST *
		Confirm GAL TEST  with multifunction button below (*)	0 R1
		The display means: Vehicle standing still. The number following R means: Direction of motion 1 = forward, 2 = backward
		Drive vehicle forwards while keeping track of numbers	e. g. 1220 R1
		Drive vehicle backwards while keeping track of numbers	e. g. 890 R2
		Press multifunction button (←)	GAL TEST *
9	Initialize GPS	Press automatic button (A) repeatedly until GPS INIT  appears	GPS INIT *
		Conform GPS INIT  with multifunction button below (*)	Enter LOCATION.....
		Enter the closest digitalized town with population of more than 50,000 with the multifunction keys	Esslingen
		A number in front of the location indicates that there are several locations with the same name	1 Esslingen/Bittburg  2 Esslingen am Neckar
		Press repeatedly to reach the right location with the automatic button (A) (allow running letters to run until they finish)	2 Esslingen am Neckar
		Press multifunction button below (*)	Enter street name.....
		Enter closest digitalized street name or CENTER  or TRAIN STATION  with the multifunction buttons	Train station
		A number in front of the street indicates that there are several streets with the same name
		Press automatic button (A) repeatedly until the right street name appears (allow running letters to run until they finish)
		Press multifunction button below (*) until message appears. . . .	Please switch off radio and ignition for 1 minute
		First switch off unit and then ignition
10	Start engine	Drive vehicle outside under free sky
11	Activate service module	Press mode button (M) repeatedly until NAVIGATE  appears	NAVIGATE
		Press automatic button (A) repeatedly until CONFIG  appears	CONFIG 1 2 3 4 5 6 7 8*
		Confirm CONFIG  with multifunction key below (*)	SYSTEM 1 2 3 4 5 6 7 8 *
		Confirm SYSTEM  with multifunction button (GHI) and (MNO)	MODULE T *
		Press automatic button (A) repeatedly until GPS TEST  appears	GPS TEST *
12	Perform GPS antenna test	Confirm GPS TEST  with multifunction button below (*)	FIX OK
		If the test is erroneous the following messages can appear: No GPS:  GPS antenna incorrectly connected NO FIX:  GPS antenna cannot receive satellites
		Press multifunction button (←)	GPS TEST *
		Press mode button (M) repeatedly until NAVIGATE  appears	NAVIGATE
13	Calibration drive	The duration of the calibration drive is dependent on the vehicle model and the number of times the direction is changed. It can be between 30 km and 100 km and can be interrupted as long as desired at any time.	Calibration status not achieved [0]
14	Calibration status achieved	When the calibration status [2] is reached the unit automatically requests entry of the location.	Please enter location.....