Remove/install oil spray nozzles (pistons) - AR18.00-P-4000DV

ENGINE 112

ENGINE 112.945 in MODEL 463.209 /232 /233 /244 /245 /250

ENGINE 113.962 in MODEL 463.206 /240 /241 /247 /248 /249 /254

ENGINE 113.982 in MODEL 463.243 /246

ENGINE 113 (except 113.995) in MODEL 129, 163, 202, 203, 208, 209, 210, 211, 215, 220, 230

Shown on engine 112

Fig 1: Identifying Oil Spray Nozzles (Pistons) Components

	Remove/install
	Risk of death caused by vehicle slipping or toppling off the lifting platform.	Align vehicle between the columns of the and position the four support plates below the lifting platform support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
1	Remove oil pan bottom section	Models 463, 220, 210, 208, 202, 170, 129.	AR01.45-P-7555VA
		Models 230.474 /475.	AR01.45-P-7555R
		Models 163.154, 163.172.	AR01.45-P-7555V
		Model 163.174.	AR01.45-P-7555VE
		Models 203, 209.361/365/375.	AR01.45-P-7555PV
		Models 211.061/065/070.
2	Remove oil pan top section	Model 129.	AR01.45-P-7500FD
		Models 163.	AR01.45-P-7500FB
		Model 170.	AR01.45-P-7500SV
		Models 203, 209.361/365/375.	AR01.45-P-7500PV
		Model 208, 202.	AR01.45-P-7500FC
		Model 210 without 4-MATIC.	AR01.45-P-7500F
		Model 210 with 4-MATIC.	AR01.45-P-7500FA
		Model 211.061/065.	AR01.45-P-7500TV
		Model 220.	AR01.45-P-7500I
		Models 230.474 /475.	AR01.45-P-7500R
		Model 463.	AR01.45-P-7500FG
3	Remove oil pump	Models 129, 163, 170, 202, 208, 210, 220, 463.	AR18.10-P-6020B
		Models 203, 209.361/365/375. Models 211.061/065/070.	AR18.10-P-6020PV
		Model 230.474 /475.	AR18.10-P-6020R
		Installation: Ensure that the oil return shutoff valve is correctly located. Clean the oil pump strainer. Fill the oil pump with engine oil before installing, so that oil is delivered at the initial startup.
4	Remove oil spray nozzles (1)	If necessary, rotate crankshaft slightly at belt pulley. Installation: Replace oil spray nozzles. It is important to ensure that the spray pipes (3) of the oil spray nozzles (1) are not bent when being installed. On engine 112.960/961 pay attention to correct version of oil spray nozzles.
4	Remove oil spray nozzles (1)		*BA18.00-P-1001-01D
	Clean
5	Inspect/clean oil ducts	Blow through oil galleries in direction of flow of oil with compressed air. Do not use any hard objects for cleaning.
6	Install in the reverse order

ENGINE LUBRICATION, ENGINE OIL COOLING, GENERAL

Number	Designation		Engine 112 except 112.951/976, 113.940/941/ 942/943/944/ 945/946/948/ 960/961/962/ 963/964/965/ 966/967/968/ 971/980/981/ 982/984/986/ 992/995	Engines 113.987/988/ 990/991/993
BA18.00-P-1001-01D	Bolt, oil-spray nozzle at crankcase	Nm	15	13