Remove/install oil dipstick guide tube - AR18.40-P-3510BV

ENGINE 112 /, 113 / (except, 112.912 /946 /961, 113.963 /995) 

Fig 1: Identifying Oil Dipstick Guide Tube Components - Shown On Engine 112

Fig 2: Identifying Oil Dipstick Guide Tube And Oil Dipstick Guide Tube Bracket - Shown On Engine 113.989

	Remove/install
	Risk of death  caused by vehicle slipping or toppling off the lifting platform.	Align vehicle between the columns of the and position the four support plates below the lifting platform support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
1	Remove lower engine compartment paneling	Models 210, 208, 202, 129	AR61.20-P-1105AB
		Model 230	AR61.20-P-1105R
		Models 163.172/ 174/ 175	AR61.20-P-1105GH
		Model 211	AR61.20-P-1105T
		Model 170	AR61.20-P-1105A
		Model 171.4	AR61.20-P-1105V
		Model 203, 209	AR61.20-P-1105P
		Model 215, 220	AR61.20-P-1105M
		Model 219.375	AR61.20-P-1105TX
		Models 163.154/ 157
		Model 219.376
2.1	Remove engine cover or air filter	Remove engine trim panel or air filter by lifting vertically up and off the cylinder head covers.
		Model 170.466 Models 203.065 / 265 Models 211.076 / 276 Model 215.374 Models 220.074/ 174 Model 230.474	AR09.10-P-1150SVK
		Model 219.375	AR09.10-P-1150TY
		Model 171.473	AR09.10-P-1150AC
		Models 203.076/ 276 Models 209.376/ 476 as of 24.4.04
3.1	Remove air filter housing	Only on vehicles with air filter located on vehicle side.
4.1	Remove bolt (8) on oil dipstick guide tube (9) bracket	Model 171.473
		External Torx set	Figure
5.1	Remove bolt for oil dipstick guide tube (2) on cylinder head cover	Except model 171.473
			*BA01.20-P-1001-01E
		External Torx set	Figure
5.2	Remove bolt (11) on oil dipstick guide tube (10) bracket	Model 171.473
			*BA01.45-P-1010-01B
		External Torx set	Figure
6.1	Remove cable strap (7) at oil dipstick guide tube (1)	Except models 203.076 /276, 171.473 Installation:  When attaching the cable strap (7) to the oil dipstick guide tube (1), pay attention to the routing of the wiring loom.
6.2	Remove mounting clip for battery cable set to starter and hook up cable set to the side	Models 203.076/ 276, 171.473
7.1	Remove oil pan	Models 203.076/ 276	AR01.45-P-7500PV
		Model 171.473	AR01.45-P-7500VT
		Models 211 061/ 065 Models 211 261/ 265	AR01.45-P-7500TV
8.1	Lift oil dipstick guide tube (1) up and out	Except model 171.473 Installation:  Replace seal (5) and O-ring (4) of oil dipstick guide tube (1) and of dipstick (3).
8.2	Take oil dipstick guide tube (1) down and out	Model 171.473 Installation:  Replace seal (5) and O-ring (4) of oil dipstick guide tube (1) and of dipstick (3).
9	Install in the reverse order
10	Risk of accident  caused by vehicle starting off by itself when engine is running. Risk of injury  caused by contusions and burns during starting procedure or when working near the running engine Run engine and inspect for leaks	Secure vehicle to prevent it from moving by itself. Wear closed and snug-fitting work clothes. Do not grasp hot or rotating parts.	AS00.00-Z-0005-01A

CRANKCASE VENTILATION, CYLINDER HEAD COVER

OIL PAN

Fig 3: Identifying External Torx Set (001 589 76 09 00)