Specified gear oils (commercial vehicles) - overview - BB00.40-P-0231-02A

For Allison transmissions, it is absolutely essential to observe the application instructions under point 3.4!

BB00.40-P-0231-00A

NOTE: For commercial vehicle axle applications in the service fill area 235.6 can be used equivalently to 235.0.

COMMERCIAL VEHICLES, VANS, sheetS 235.0 UP TO 235.27

Major assembly

SAE grade

sheet No.

235.0

235.1

235.4

235.5

235.6

235.8

235.9

235.10

235.11

235.12

235.13

235.20

235.27

Hypoid axle, except HA 746.2

85 W-90, 90

•

◦

Hypoid axle, HA 746.211/216/217
HA 746.210 as of M 140 394
HA 746.213 as of M 138 407 except in model 374

80W-90

•

Hypoid axle, HA 746.210 as of M 140 394
HA 746.213 as of M 138 407 in model 374

•

Spur gear axle
ZF transfer case
Fuller transmission

80, 80 W
80 W/85 W (Hot zones SAE 90, 85 W-90)

•

Planetary axle

85 W-90, 90

•

MB transfer case ⁽⁶⁾

80W

•

Transfer case

80 W/85 W

◦

•

MB transfer case

80 W/85
W75W-90

•

MB manual transmission

G 1/15, 1/17, 1/18 ⁽¹⁾
G 2/24, 2/27
G 3/36, 3/40
G 3/50 ⁽¹⁾
G 3/60 ⁽¹⁾, 3/61
G 3/70

80, 80 W ⁽¹⁾
80 W/85 W ⁽¹⁾

• ⁽¹⁾

G 1/D 14
G 3/45-6, 3/55-6, 3/65, 3/90
G 4/65-6, 4/95-6, 4/95-7, 4/110-6
G 65-7
G 100/125/135 155/180/200
GO 3/60, GO 3/80
GO 4/95/105/120/130
GTO 24-5
GV 4/65-6, 4/95-6, 4/110-6

30, 40
80, 80 W
80 W/85 W (Hot zones SAE 90, 85 W-90)

•

• ⁽²⁾

GO 160/170/190/210

75W-90

•

G 16/28/20/32/33

75W/8

•

G 60, G56, G 85

75W/90W

•

◦ ⁽²⁾

•

G60, G56, G85 in tropical countries

•

G100, G131-9, G 210,
G 211, G 240, G260,
G131, G221, G230, G231

80W

• ⁽³⁾

•

ZF manual transmission

80, 80 W
85 W
75 W/85 W (Hot zones SAE 90, 85 W-90)

•

• ⁽⁴⁾

•

• ⁽⁵⁾

ZF converter and clutch unit 400

•

Voith retarder

10 W, (30)
20 W-20

•

AG 4
- automatic part

- final-drive assembly

•

Sprintshift transmission (SSG)

75W/85W

•

This table only serves as an overview!
• Should be used.
◦ Can be used.

⁽¹⁾	Only for: G 1/18-5, G 3/50, G 3/60 without MS synchronization

⁽²⁾	Use engine oils as under sheet 235.12, SAE 30 for common oil circuits with ZF torque converter clutch 400

⁽³⁾	Transmissions with oil coolers only.

⁽⁴⁾	With intarder

⁽⁵⁾	Use engine oils as under sheet 235.27, SAE 30 for common oil circuits with ZF torque converter clutch 400

⁽⁶⁾	Only use in exceptional cases! If no synthetic oil in accordance with 235.4 or 235.11 available.

COMMERCIAL VEHICLES, VANS, sheetS 236.1 UP TO 236.91

Major assembly

SAE grade

sheet No.

236.1

236.2

236.3

236.5

236.6

236.7

236.8

236.9

236.11

236.81

236.91

Mechanical steering

ATF

•

MB manual transmission ⁽²⁾
G 1/15, 1/17, 1/18
G 2/24, 2/27
G 3/36, 3/40
G 3/50
G 3/60, 3/61
G 3/70

ATF

•

MB power steering

ATF

•

ZF power steering

ATF

•

Hydraulic fan drive for auxiliary radiator

ATF

•

MB automatic transmission

ATF

•

MB automatic transmission W 4 B 035 ⁽¹⁾

ATF

•

Voith/ZF automatic transmission

ATF

•

Allison transmission ⁽³⁾

ATF

•

• ⁽⁴⁾

ZF 4 HP 20

ATF

•

AG 4

- automatic part

•

- final-drive assembly

Hydraulic lowering system in model 905.613

•

This table only serves as an overview!
• Should be used.

⁽¹⁾	Only install W 4 B 035 as of major assembly end no 00 57 33 or modified shift plate. ATF as per, sheets 236.1, 236.8, and 236.81 may not be used in W 4 B 035.

⁽²⁾	Only for: G 1/18-5, G 3/50, G 3/60 with MS synchronization

⁽³⁾	For Allison transmissions, it is absolutely essential to observe the application instructions on sheet 231.0 under point 3.4!

⁽⁴⁾	Automatic transmission fluids (ATF), sheet 236.91 or TES 295 for Allison automatic transmission. This oil permits much longer oil change intervals, in particular for Allison transmissions.

When changing to a different oil:

Change service life factors in the maintenance system (WS) and pay attention to specified maintenance intervals.