Check and adjust camber and caster at front axle - AR40.20-P-0322D

MODEL 210.00 /01 /02 /03 /04 /05 /06 /07 /20 /21 /22 /23 /24 /26 /27 /6 

Camber 

Fig 1: Identifying Camber Front Axle - Model 210.00 /01 /02 /03 /04 /05 /06 /07 /20 /21 /22 /23 /24 /26 /27 /6

Caster 

Fig 2: Identifying Caster Front Axle - Model 210.00 /01 /02 /03 /04 /05 /06 /07 /20 /21 /22 /23 /24 /26 /27 /6

	Check
	Risk of injury  from jamming or bruises  when working on springs or spring bosses which are tensioned	Use only approved tensioning devices; additionally shield off hazardous area if necessary. Inspect special tools for damage and proper operation (visual inspection). Wear protective gloves.	AS00.00-Z-0001-01A
1	Observe general information on chassis alignment		AR40.20-P-0201A
2.1	Check vehicle level at front and rear axle with Mercedes-Benz measuring device and adjust if necessary	with Mercedes-Benz measuring device
		Models 210.00/01/02/03/04/05/06/07/20/21/22/23/24/26/27	AR40.20-P-0300C
2.2	Check vehicle level at front and rear axle with electronic inclinometer and adjust if necessary	with electronic inclinometer
		Models 210.00/01/02/03/04/05/06/07/20/21/22/23/24/26/27	AR40.20-P-0301C
		Model 210.6	AR40.20-P-0301D
3	Check camber and assign tabular value	Models 210.00/01/02/03/04/05/06/07/20/21/22/23/24/26/27	AR40.20-P-0322-02C
		Model 210.6	AR40.20-P-0322-02E
4	Check caster and assign tabular value	Measurement with wheels turned 20°.
		Models 210.00/01/02/03/04/05/06/07/20/21/22/23/24/26/27	AR40.20-P-0322-03C
		Model 210.6	AR40.20-P-0322-03D
	Adjust
5	Raise vehicle.
6	Clamp front spring		AR32.20-P-0200-01A
7	Install repair bolt (19c)	Screw on nut (19b) of repair kit until it abuts, but do not tighten yet, so that the rubber mount of the transverse control arm can twist when the vehicle is rocked to settle the suspension.	AR40.20-P-0322-01C
8	Unclamp front springs	Lower vehicle and settle the suspension by pulling and pushing firmly several times.
9	Check the vehicle level at the front axle again after the camber and caster adjustment	The vehicle level must match the dimension established during the initial measurement. with Mercedes-Benz measuring device:
		Models 210.00/01/02/03/04/05/06/07/20/21/ 22/23/24/26/27	AR40.20-P-0300C
		with electronic inclinometer:
		Models 210.00/01/02/03/04/05/06/07/20/21/22/23/24/26/27	AR40.20-P-0301C
		Model 210.6	AR40.20-P-0301D
10	Tighten nut (19b) of repair kit	The repair bolt (19c) 19 must not be twisted after fixing in position by the adjusting washers and should be counter-held when tightening the nut (19b) of the repair kit.
			*BA40.20-P-1005-01A
11	Check toe-in at front and rear axle and adjust if necessary.	See ↓
		Perform chassis alignment check	AR40.20-P-0200A

Chassis alignment