LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 1995 >> C220 >> Repair and Diagnosis >> External Pages >> Different car >> Section 73 (Rear Axle - 140 Chassis) >> Testing & Repair >> Remove/install rear rubber mount for center assembly mount in rear axle carrier - AR35.10-P-0050A >> Install front differential mount - AR35.10-P-0050-01A

Install front differential mount - AR35.10-P-0050-01A

WARNING: This page does not describe the selected car, but rather 42 other vehicles, including the 1999 Mercedes-Benz S600, 1999 Mercedes-Benz S500, 1999 Mercedes-Benz S420, 1999 Mercedes-Benz S320, and 1999 Mercedes-Benz CL600. However, it is still accessible from the selected car via links, so may be relevant.
       
REFER TO COMPONENT MODIFICATIONS Front rear axle center assembly mounting modified Model 129.060/061/066 BT35.31-P-0001-01A
REFER TO COMPONENT MODIFICATIONS Front rear axle center assembly mounting modified Model 202.018/022/028/120/121/125 BT35.31-P-0001-01B
TORQUE SPECIFICATION REAR AXLE CARRIER

Number Designation Model 129 Model 140 Model 170
BA35.10-P-1003-01A Self-locking nut, rear axle differential at front to rear axle carrier Nm 45 45 50
TORQUE SPECIFICATION REAR AXLE CARRIER

Number Designation Model 202 Model 203 Model 208
BA35.10-P-1003-01A Self-locking nut, rear axle differential at front to rear axle carrier Nm 50 45 50
TORQUE SPECIFICATION REAR AXLE CARRIER

Number Designation Model 209 Model 210
BA35.10-P-1003-01A Self-locking nut, rear axle differential at front to rear axle carrier Nm 43 45

Illustrated on model 140 

  1. Mount rubber bushing (60b) and short plate with 14 mm height (60a) above in the rear axle carrier (1).
  2. Mount rubber bushing with guide collar (60c) and long plate with 17 mm height (60d) below, pay attention to proper seating of bearing.
  3. Install appropriate shim (60e) between plate (60d) and rear axle center assembly (50).
  4. Replace self-locking hexagon nut (52), install rear axle center assembly (50) at rear axle carrier (1).
    Fig 1: Identifying Rear Axle Center Assembly At Rear Axle Carrier - Model 140
    G04713324Courtesy of MERCEDES-BENZ OF NORTH AMERICA.

IMPORTANT Installation for model 129

On vehicles with automatic transmission up to approx. 08/89 install short plate with 14 mm height (60a) above and long plate with 17 mm height (60d) below.

On vehicles with automatic transmission as of 09/89 and on vehicles with manual transmission, both plates (60a, 60d) have a height of 15 mm.

Install appropriate shim (60e with notches) at rear axle center assembly (50).

Fig 2: Identifying Rear Axle Center Assembly At Rear Axle Carrier - Model 129
G04713325Courtesy of MERCEDES-BENZ OF NORTH AMERICA.

IMPORTANTInstallation, model 170, 202, 203, 208, 209 

Replace self-locking hexagon nut or plate with integrated locking nut (60a).

1 or 2 shims (60e) can be installed for the rear axle center assembly depending on the version.

Fig 3: Identifying Rear Axle Center Assembly At Rear Axle Carrier - Model 170, 202, 203, 208, 209
G04713326Courtesy of MERCEDES-BENZ OF NORTH AMERICA.

Shows model 210 

Fig 4: Identifying Rear Axle Center Assembly At Rear Axle Carrier - Model 210
G04713327Courtesy of MERCEDES-BENZ OF NORTH AMERICA.
scientia non olet · About LEMON Manuals