Removal and installation of door liner - RA72001290100X(72-100)

Operation number of the operation texts and work units or standard texts and flat rates respectively

Fig 1: Identifying Door Liner Components

Courtesy of MERCEDES-BENZ OF NORTH AMERICA.

Screws on chrome trim (1) 3 each	screw out and remove chrome trim.
Screw on lock cover plate (2)	screw out.
Lock cover plate (2)	pull down and remove.
Cover (3) on mirror triangle	press off and remove toward top.
Knob (4) for interior locking mechanism	press off and pull out.
Small wood cover (5) on inside door control	press off and remove
Door pocket cover	open
Front cover (arrow)	press off and remove.
Entry light (6)	pull out downward, pull off electrical connections and lay light to side.
Frame on inside door control	screw off and remove.
Large wood cover (7)	press to the rear and remove from door liner.
Electrical connections on seat control switch	disconnect and lay wood cover (7) aside.
Screw on inside door control	screw out (10 mm wrench).
Screw in area of door pocket, front (arrow)	screw out.
Screw in area of door pocket, rear (arrow)	screw out.
Door liner (8)	unclip from inside door panel at bottom as well as front and back (8 clips).
Door liner (8)	pull away from inside door panel at bottom and remove toward top.
Vacuum line and electrical wires on door liner	disconnect and pull through.
Door liner (8)	lay aside.
Before installing door liner	check door foil for damage, replace if required.
Install	in opposite order.

Removal, installation

Screw out screw on chrome trim and lock cover plate.
Remove chrome trim and lock cover plate.

Fig 2: Locating Chrome Trim And Lock Cover Plate Screw
Courtesy of MERCEDES-BENZ OF NORTH AMERICA.
Press cover off of mirror triangle and remove upward.

Fig 3: Pressing Cover Off Of Mirror Triangle
Courtesy of MERCEDES-BENZ OF NORTH AMERICA.
Press off small wood cover and knob for inside locking mechanism and remove (arrows).

Fig 4: Pressing Off Small Wood Cover And Knob For Inside Locking Mechanism
Courtesy of MERCEDES-BENZ OF NORTH AMERICA.
Open door pocket cover and press off front cover (arrow).

Fig 5: Locating Open Door Pocket Cover
Courtesy of MERCEDES-BENZ OF NORTH AMERICA.
Pull out entry light downward. Disconnect electrical connections and lay light aside.

Fig 6: Locating Electrical Connections And Lay Light
Courtesy of MERCEDES-BENZ OF NORTH AMERICA.
Screw frame off of inside door control and remove (arrow).

Fig 7: Locating Screw Frame Off Of Inside Door Control
Courtesy of MERCEDES-BENZ OF NORTH AMERICA.
Press large wood cover downward and remove from door liner (arrows).

Fig 8: Locating Large Wood Cover Downward
Courtesy of MERCEDES-BENZ OF NORTH AMERICA.
Disconnect plug connector and lay wood cover to side (arrow).

Fig 9: Locating Plug Connector And Lay Wood Cover
Courtesy of MERCEDES-BENZ OF NORTH AMERICA.
Screw out screw on inside door control (arrow).

Fig 10: Locating Screw On Inside Door Control
Courtesy of MERCEDES-BENZ OF NORTH AMERICA.
Screw out screw at front of door pocket (arrow).

Fig 11: Locating Screw At Front Of Door Pocket
Courtesy of MERCEDES-BENZ OF NORTH AMERICA.
Screw out screw at rear of door pocket (arrow).

Fig 12: Locating Screw At Rear Of Door Pocket
Courtesy of MERCEDES-BENZ OF NORTH AMERICA.
Pull door liner off of inside door panel at bottom, front and rear. Pull door liner away from inside door panel at bottom and remove upward (arrows).
Disconnect vacuum line and electrical wiring on door liner.
Lay door liner to side.

Fig 13: Locating Door Liner
Courtesy of MERCEDES-BENZ OF NORTH AMERICA.
Before installing door liner check door foil. Replace foil if damaged and glue on without wrinkles.
Install in reverse order.

Fig 14: Identifying Door Liner Check Door Foil
Courtesy of MERCEDES-BENZ OF NORTH AMERICA.

Rear side of door liner showing position of clips (8 each, arrows).

Fig 15: Locating Rear Side Of Door Liner Clips Position
Courtesy of MERCEDES-BENZ OF NORTH AMERICA.