Render new vehicles, which were immobilized operational - AP00.70-P-1001ZZ

MODEL 129, 140, 163, 168, 170, 202, 203, 208, 209, 210, 211, 215, 220, 230, 240 

MODEL 461.302 /332 /342 /345 

MODEL 463.200 /204 /206 /207 /208 /209 /220 /221 /224 /225 /227 /228 /230 /231 /232 /233 /240 /241 /243 /244 /245 /246 /247 /248 /249 /250 /254 /270 /271 /300 /304 /307 /308 /309 /320 /321 /322 /323 /324 /325 /327 /328 /330 /331 /332 /333 

1	Perform delivery inspection
2	Check battery		AR54.10-P-1129-01A
3	Vent stationary heater and top up coolant	Model 163, 168, 170, 202, 203, 208, 209, 210, 211, 215, 220, 230, 240, 461, 463
+		Models 129, 140 with stationary heater, code 228	ra83001291165x
4	Check fluid level of engine cooling system, correct if necessary and check corrosion protection as well as antifreeze and correct if necessary	Model 129, 140, 163, 168, 170, 202, 203, 208, 209, 210, 211, 215, 220, 230, 240
		Model 463 with engine 112, 113	AP20.00-P-2010GA
		Models 461, 463 with engines 102, 103, 104, 117, 602, 603, 606, 612, 628	AP20.00-P-2010G
	Risk of accident  caused by vehicle starting off by itself when engine is running. Risk of injury  caused by contusions and burns during starting procedure or when working near engine	Secure vehicle to prevent it from moving. Wear closed and snug-fitting work clothes. Do not grasp hot or rotating parts.	AS00.00-Z-0005-01A
5	Start engine	Allow to run at idle speed until oil pressure is displayed.
6	Check refrigerant level of air conditioning system
		Model 129 up to 31.5.96 with automatic air conditioning, code 581a, Model 140 up to 31.5.95 with automatic air conditioning, code 581a with rear air conditioner, code 582, Model 202 up to 30.9.95 with automatic air conditioning, code 581a, Models 129, 170, 202, 208, 210, 220 with air conditioning (or Tempmatic for USA), code 580	AP83.30-P-8312DA
		Models 461, 463 with air conditioning, code H02	AP83.30-P-8312G
7	Move the pull switch of the hydropneumatic suspension into position N and allow the engine to run at increased idle speed until the vehicle has reached its normal level	Only for Hydropneumatic suspension with automatic level lowering device and controlled damping, code 215c, All-round hydropneumatic suspension, code 487
8	Brake testing on test stand
		Model 129, 140, 170, 202, 203, 208, 209, 210, 215, 220	AP42.00-P-4290BA
		Models 461, 463	AP42.00-P-4290G
9	Check brake disks for signs of corrosion.	For vehicles which were parked for more than 6 months.
10	Replace brake fluid	For vehicles which were parked for more than 6 months.
		Model 140 as of 1.7.93 except code 471 Model 170 except code 471 Model 202 up to 31.5.94 except code 471 Model 202 with code 472 Model 208 except 208.474 except code 471 Model 210 except code 471 Model 210 except 210.072/272 with code 472 Model 215 with code 472 Model 220 except code Z07	AP42.00-P-4280BA
		Model 129, 140 as of 1.7.93 up to 31.5.94 with code 471	AP42.00-P-4280BB
		Model 129 as of 1.7.93 except code 212/471/472 Model 129.059 059/064/ 064 /068n	AP42.00-P-4280BC
		Model 202 up to 31.5.94 with code 471	AP42.00-P-4280EA
		Models 461, 463	AP42.50-P-4280G
11	Remove transport film	Model 168, 461, 463
	Installing transport foil	Models 129, 140, 163, 170, 202, 203, 208, 209, 210, 211, 215, 220, 230, 240 with Paint protection, code 524	AR97.20-P-4000A
	Notes on paintwork, decorative and detachable components	Model 124, 126, 129, 140, 163, 168, 170, 201, 202, 203, 208, 209, 210, 211, 215, 220, 230, 463	AH98.00-P-9019-01Z
	Notes on transportation sheeting	Model 129, 163, 168, 170, 202, 203, 208, 209, 210, 211, 215, 220, 230, 240, 414	AH97.20-P-9409-03A
12	Wash the vehicle	Preclean using high pressure or steam cleaning equipment. This will remove any coarse dirt particles.
13	Remove drips or rough linings on the paintwork, the windows or trim parts	Use metal dust remover or solvent (e.g. pure benzene, silicone remover, artificial-resin thinner). On non-painted plastic parts do not use aggressive cleaning agents. Only for Activated charcoal filter, code 306: Cover inside of air inlet grille on engine hood.
		Cleaner	*BR00.45-Z-1017-04A
14	Treat paintwork using polishing paste and buffer	If films still on paintwork.
		Polish	*BR00.45-Z-1015-04A
15	Perform treatment using polish and gloss preservation.	Polish	*BR00.45-Z-1013-04A
		Gloss preserver	*BR00.45-Z-1014-04A