Align connecting rod - AR03.10-P-6111-04AW
INSPECTION DATA FOR A CONNECTING ROD
| Number |
Designation |
Engine 601.921 
up to 09/84 |
Engine 601.921
as of 10/84 |
| BE03.10-P-1003-01C |
Dimension |
permissible twist of connecting rod bearing bore to connecting rod bush bore over a length of 100 mm |
mm |
0.1 |
0.1 |
| BE03.10-P-1004-01C |
Dimension |
Permissible variation of axial parallelism of connecting rod bearing bore to connecting rod bush bore over a length of 100 mm |
mm |
0.045 |
0.045 |
INSPECTION DATA FOR A CONNECTING ROD
| Number |
Designation |
Engine 601 up to 09/84 except 601.921 |
Engine 601 as of 10/84 except 601.921
, engine 602.91, 603.91 |
| BE03.10-P-1003-01C |
Dimension |
permissible twist of connecting rod bearing bore to connecting rod bush bore over a length of 100 mm |
mm |
0.1 |
0.1 |
| BE03.10-P-1004-01C |
Dimension |
Permissible variation of axial parallelism of connecting rod bearing bore to connecting rod bush bore over a length of 100 mm |
mm |
0,045 |
0,045 |
CONNECTING ROD
| Number |
Designation |
Engines 601, 602 except 602.98, 603 except 603.970 up to 11/90 603.970 up to 8/90 |
Engines 601, 602 except 602.98, 603 except 603.970 as of 12/90 - 10/92 603.970 as of 9/90 - 10/92 |
Engines 601, 602 except 602.98, 603 as of 11/92 |
| BA03.10-P-1001-01C |
Connecting rod bolt (stretch shank) |
1st stage |
new |
Nm |
- |
45 |
40 |
| used |
Nm |
- |
40 |
- |
| Step 2 |
|
∠ ° |
- |
90 |
90 |
| See picture in |
|
|
- |
AR03.10-P-6111-01AW |
AR03.10-P-6111-01AW |
| BA03.10-P-1002-01C |
Connecting rod bolt (stretch bolt) |
1st stage |
|
Nm |
30 |
- |
- |
| Step 2 |
|
∠ ° |
90 |
- |
- |
| See picture in |
|
|
AR03.10-P-6111-01AW |
|
|
INSPECTION DATA FOR A CONNECTING ROD
| Number |
Designation |
Engines 602.96, 603.96 |
Engine 603.97 |
| BE03.10-P-1003-01C |
|
permissible twist of connecting rod bearing bore to connecting rod bush bore over a length of 100 mm |
mm |
0,1 |
0,1 |
| BE03.10-P-1004-01C |
|
Permissible variation of axial parallelism of connecting rod bearing bore to connecting rod bush bore over a length of 100 mm |
mm |
0.045 |
0.045 |
COMMERCIALLY AVAILABLE TOOLS
| Number |
Designation |
| WH58.30-Z-1008-05A |
Connecting rod tester |
| WH58.30-Z-1009-05A |
Conrod straightening equipment |
- Check connecting rod with mount bearing shell and piston pin using a connecting rod tester.
- Align connecting rod bearing bore to be parallel to the connecting rod bush bore using the connecting rod aligning tool.
Courtesy of MERCEDES-BENZ OF NORTH AMERICA.
- Align axle twist of the connecting rod bearing bore to the connecting rod bush bore using the connecting rod aligning tool.
Courtesy of MERCEDES-BENZ OF NORTH AMERICA.