Checking rear axle camber - AR40.20-P-0331A

MODEL 129, 140, 170, 202, 208, 210 

Fig 1: Identifying Rear Axle Camber - Model 129, 140, 170, 202, 208, 210

	Checking
1.1	Check vehicle level at front and rear axles and adjust if necessary	With Mercedes-Benz measuring device.
		Model 129, model 170 up to 28.02.00, model 170 with AMG lowering kit, models 202, 208	AR40.20-P-0300A
		Model 129 with ADS	AR40.20-P-0300D
		Model 129 with ADS II	AR40.20-P-0300E
		Model 140	AR40.20-P-0300B
		Model 210.00/01/02/03/04/05/06/07/20/21/22/23/24/26/27	AR40.20-P-0300C
1.2	Check vehicle level at front and rear axles with electronic clinometer and adjust if necessary	With electronic clinometer.
		Models 170, 202, 208	AR40.20-P-0301A
		Model 210.00/01/02/03/04/05/06/07/20/21/22/23/24/26/27	AR40.20-P-0301C
		Model 210.08/28/6	AR40.20-P-0301D
2	Check rear axle camber	The camber on the rear axle is not adjustable. If substantial deviations in the rear axle camber are found, the cause may be one of the following: Too great a difference in vehicle level between right and left-hand sides of vehicle. Camber strut bent. Accident damage to the frame floor. Level differences at the mounting points for the rear axle carrier between the left and right sides of the body. Experience shows that bending caused by an accident also has an effect on the toe.
		Models 129, 140	*BE40.20-P-1001-09A
		Model 210.0/2	*BE40.20-P-1001-09B
		Model 210.6	*BE40.20-P-1001-09F
		Model 170	*BE40.20-P-1001-09H
		Models 202, 208	*BE40.20-P-1001-09C

REAR AXLE CAMBER

	Number	Designation	Model 129	Model 140
BE40.20-P-1001-09A	Camber at vehicle level	+40 mm	-0° 30' ± 30'	-0° 22' ± 30'
+30 mm			-0° 45' ± 30'	-0° 30' ± 30'
+20 mm			-1° ± 30'	-0° 40' ± 30'
+10 mm			-1° 15' ± 30'	-0° 46' ± 30'
0 mm			-1° 30' ± 30'	-1° ± 30'
-10 mm			-1° 45' ± 30'	-1° 15' ± 30'
-20 mm			-2° ± 30'	-1° 30' ± 30'
-30 mm			-2° 15' ± 30'	-1° 45' ± 30'
-40 mm			-2° 34' ± 30'	-2° ± 30'
	-50 mm		-2° 52' ± 30'	-2° 17' ± 30'

Test values for rear axle camber

		Number	Designation	Model 210.0/2
BE40.20-P-1001-09B	Camber at vehicle level	+40 mm	°∠ 3.0	-0° 42' (±30')
+30 mm			°∠ 2.0	-0° 52' (±30')
+20 mm			°∠ 2.0	-1° 04' (±30')
+10 mm			°∠ 0	-1° 17' (±30')
0 mm			°∠ -1.1	-1° 30' (±30')
-10 mm			°∠ -2.1	-1° 44' (±30')
-20 mm			°∠ -3.1	-1° 59' (±30')
-30 mm			°∠ -4.1	-2° 16' (±30')
-40 mm			°∠ -5.1	-2° 34' (±30')
	-50 mm		°∠ -6.1	-2° 52' (±30')

Test values for rear axle camber

		Number	Designation	Model 202	Model 208
BE40.20-P-1001-09C	Camber at vehicle level	40mm	∠° 3.9	-0° 30' (±30')	-0° 30' (±30')
30 mm			∠° 2.9	-0° 45' (±30')	-0° 45' (±30')
20 mm			∠° 1.8	-1° (±30')	-1° (±30')
10 mm			∠° 0.7	-1° 15' (±30')	-1° 15' (±30')
0 mm			∠° 0.4	-1° 30' (±30')	-1° 30' (±30')
-10 mm			∠° -1.5	-1° 45' (±30')	-1° 45' (±30')
-20 mm			∠° -2.5	-2° (30')	-2° (±30')
-30 mm			∠° -3.6	-2° 15' (±30')	-2° 15' (±30')
-40 mm			∠° -4.7	-2° 34' (±30')	-2° 34' (±30)
	-50 mm		∠° -5.8	-2° 52' (±30')	-2° 52' (±30)

Test values for rear axle camber

		Number	Designation	Model 210.6
BE40.20-P-1001-09F	Camber at vehicle level	±30 mm	°∠ 2.8	-0° 51' (±30')
±20 mm			°∠ 1.8	-1° 03' (±30)
±10 mm			°∠ 0.8	-1° 16' (±30')
0 mm			°∠ -0.2	-1° 30' (±30')
	-10 mm		°∠ -1.3	-1° 45' (±30')

Test values for rear axle camber

			Number	Designation	Model 170 up to 28.02.00	Model 170 as of 01.03.00
BE40.20-P-1001-09H	Camber at vehicle level	40 mm	3.9 °	∠°	-0° 30' (±30')	-
30 mm			2.9 °	∠°	-0° 45' (±30')	-
20 mm			1.8 °	∠°	-0° 30' (±30')	-
10 mm			0.7 °	∠°	-1° (±30')	-
0 mm			-0.4 °	∠°	-0° 30' (±30')	-
-10 mm			-1.5 °	∠°	-1° 45' (±30')	-
-20 mm			-2.5 °	∠°	-2° (±30')	-
-30 mm			-3.6 °	∠°	-2° 15' (±30')	-
-40 mm			-4.7 °	∠°	-2° 34'	-
	-50 mm		-5.8 °	∠°	-2° 52'	-
	BE40.20-P-1002-09H	Camber at vehicle level	1.6 °	∠°	-	-1 ° 13' (±30')
		1.4 °		∠°	-	-1 ° 16' (±30')
		1.2 °		∠°	-	-1 ° 18' (±30')
		1.0 °		∠°	-	-1 ° 21' (±30')
		0.8 °		∠°	-	-1 ° 24' (±30')
		0.6 °		∠°	-	-1 ° 27' (±30')
		0.4 °		∠°	-	-1 ° 29' (±30')
		0.2 °		∠°	-	-1 ° 32' (±30')
		0 °		∠°	-	-1 ° 35' (±30')
		-0.2 °		∠°	-	-1 ° 38' (±30')
		-0.4 °		∠°	-	-1 ° 41' (±30')
		-0.6 °		∠°	-	-1 ° 44' (±30')