Intention of troubleshooting procedure

WARNING: This page is about a different variant/trim than selected.

Step 1
- Perform a unit inspection of the battery.
Step 2
- Perform an inspection of the battery and DC-DC converter-related connectors.
- Inspect the wiring harness between the battery and DC-DC converter.
Step 3
- Perform an inspection of the DC-DC converter and PCM-related connectors.
- Inspect the wiring harness between the DC-DC converter and PCM.
Step 4
- Verify if the malfunctioning location is the DC-DC converter.
Repair completion verification
- Verify that the primary malfunction is resolved and there are no other malfunctions.

P0A94: 00 (PCM (PYUL)) DIAGNOSTIC PROCEDURE

Step	Inspection	Results	Action
1	PURPOSE: VERIFY BATTERY FOR MALFUNCTION Inspect the applicable part. (Refer to [BATTERY INSPECTION ] in service information). Is the part normal?	Yes	Go to the next step.
1		No	Recharge or replace the battery and perform the repair completion verification 1. (Refer to [BATTERY RECHARGING ] in service information). (Refer to [BATTERY REMOVAL/INSTALLATION ] in service information).
2	PURPOSE: INSPECT WIRING HARNESS (INCLUDING CONNECTOR/TERMINAL) BETWEEN BATTERY AND DC-DC CONVERTER FOR MALFUNCTION Inspect the applicable circuit. (See CIRCUIT INSPECTION .) (See CONNECTOR INSPECTION .) Is the circuit normal?	Yes	Go to the next step.
2		No	Repair or replace the malfunctioning location and perform the repair completion verification 1.
3	PURPOSE: INSPECT WIRING HARNESS (INCLUDING CONNECTOR/TERMINAL) BETWEEN DC-DC converter AND PCM FOR MALFUNCTION Inspect the applicable circuit. (See CIRCUIT INSPECTION .) (See CONNECTOR INSPECTION .) Is the circuit normal?	Yes	Go to the next step.
3		No	Repair or replace the malfunctioning location and perform the repair completion verification 1.
4	PURPOSE: PERFORM DTC INSPECTION AND VERIFY IF MALFUNCTIONING PART IS DC-DC CONVERTER Install/connect the part removed/disconnected during the troubleshooting procedure. Clear the DTC recorded in the memory. (See CLEARING DTC .) Replicate the vehicle conditions at the time the DTC was detected using the following procedure. Implement the repeatability verification procedure. (See Repeatability Verification Procedure ). Perform the DTC inspection for the PCM. (See DTC INSPECTION .) Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See MALFUNCTION DIAGNOSIS FLOW [CONTROLLER AREA NETWORK (CAN)] .) If the CAN communication is normal, replace the DC-DC converter and perform the repair completion verification 1. (Refer to [DC-DC CONVERTER REMOVAL/INSTALLATION ] in service information).
4		No	Go to repair completion verification 2.
Repair completion verification 1	PURPOSE: VERIFY THAT VEHICLE IS REPAIRED Install/connect the part removed/disconnected during the troubleshooting procedure. Clear the DTC recorded in the memory. (See CLEARING DTC .) Replicate the vehicle conditions at the time the DTC was detected using the following procedure. Implement the repeatability verification procedure. (See Repeatability Verification Procedure ). Perform the DTC inspection for the PCM. (See DTC INSPECTION .) Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See MALFUNCTION DIAGNOSIS FLOW [CONTROLLER AREA NETWORK (CAN)] .) If the CAN communication is normal, perform the diagnosis from Step 1. If the malfunction recurs, replace the PCM, then go to the next step. (Refer to [PCM REMOVAL/INSTALLATION ] in service information).
Repair completion verification 1		No	Go to the next step.
Repair completion verification 2	PURPOSE: VERIFY IF OTHER DTCs DISPLAYED Perform the DTC inspection. (See DTC INSPECTION .) Are any other DTCs displayed?	Yes	Repair or replace the malfunctioning location according to the applicable DTC troubleshooting.
Repair completion verification 2		No	DTC troubleshooting completed.