Simulation Table [Pcm (VIN Y)]

WARNING: This page is about a different variant/trim than selected.

-: Not applicable

SIMULATION DESCRIPTION (PCM - VIN Y)

Simulation item	Unit/Operation	Data contents	Operation condition
Simulation item	Unit/Operation	Data contents	Engine condition	Other condition
AIRSHUT_POS_COMD	% Open	Changes % to forcibly open/close the active air shutter.	Not applicable	NOTE: Override drive parameter: 0-100%
CHARGE_LAMP	No (False)/Yes (True)	Select No/Yes to turn on/off the charging system warning light. Select No/Yes to display/not display the charging system warning indication on the multi-information display.	Under the following conditions: Ignition switch ON (engine off) Idle Racing (not idle)	Not applicable
CSTR_VENT_SOL_DUTY	%	Changes % and forcibly drives/stops CV solenoid valve.	Under the following conditions: Ignition switch ON (engine off) Idle Racing (not idle)	WARNING: Do not add fuel with the CV solenoid valve closed. Otherwise, it will result in air pollution because the evaporative gas in the fuel tank will escape directly into the atmosphere. NOTE: Override drive parameter: 0% CV solenoid valve: open Override drive parameter: 100% CV solenoid valve: close
ENG_COOL_VLV_POS_COMD	° (deg)	Changes ° (deg) and forcibly drives/stops coolant control valve.	Under the following conditions: Ignition switch ON (engine off)	NOTE: Override drive parameter: 0-119°
ENG_RPM_DSD	Rpm	Changes value (Rpm) to forcibly vary engine speed.	Under the following conditions: Idle Racing (not idle)	The use in the following ranges is recommended: Engine coolant temperature: 75-95°C {167-203°F} Vehicle speed: 0 km/h {0 mph} Override drive parameter input range: 550-2, 000 Rpm
EX_SHUT_VLV_DSD	° (deg)	Changes ° (deg) and forcibly drives/stops exhaust shutter valve.	Not applicable	NOTE: Override drive parameter: 0-66°
FAN	%	Changes % and forcibly drives/stops fan control module.	Under the following conditions: Ignition switch ON (engine off) Idle Racing (not idle)	NOTE: Override drive parameter: 0-90%
FP_DUTY	%	Changes % and forcibly drives/stops fuel pump.	Under the following conditions: Ignition switch ON (engine off) Idle Racing (not idle)	WARNING: Do not use the simulation function while the fuel hose between the high pressure fuel pump and fuel pump is removed. NOTE: Override drive parameter: 5-95%
FUEL_PUMP_REQ	Off/On	Select Off/On to forcibly drive/stop the fuel pump.	Under the following conditions: Ignition switch ON (engine off) Idle Racing (not idle)	Not applicable
INJ	-	Forcibly stops the fuel injectors while the engine is idling.	Under the following conditions: Idle	WARNING: Do not use the simulation function while the vehicle is being driven. Stopping the fuel ejection causes the engine to stall which may cause the brakes to not function.
MIL	Off/On	Select Off/On to turn on/off the check engine light.	Under the following conditions: Ignition switch ON (engine off) Idle Racing (not idle)	Not applicable
OIL_PRES_SOL	OFF/ON	Select OFF/ON to forcibly drive/stop the engine oil solenoid valve.	Not applicable	Not applicable
OIL_PUMP_DUTY	% Duty Cycle	Changes % and forcibly drives/stops engine oil solenoid valve.	Under the following conditions: Idle	Not applicable
PRG_DUTY	%	Changes % and forcibly drives/stops purge solenoid valve.	Under the following conditions: Ignition switch ON (engine off) Idle Racing (not idle)	NOTE: Override drive parameter: 0% Purge solenoid valve: close Override drive parameter: 100% Purge solenoid valve: open
WHEEL_DRIVE_CTRL_COMD	-	Forcibly drives/stops AWD solenoid.	Under the following conditions: Ignition switch ON (engine off) Idle Racing (not idle)	NOTE: If the AWD solenoid is forcibly driven, the AWD warning light flashes.