Simulation Table [Pcm (VIN M)]

-: Not applicable

SIMULATION DESCRIPTION (PCM - VIN M)

Simulation item	Unit/Operation	Data contents	Operation condition
Simulation item	Unit/Operation	Data contents	Engine condition	Other condition
A/C_SW	FALSE/TRUE	Select FALSE/TRUE to disengage/engage the magnetic clutch.	Under the following conditions: Idle (no load)	-
AIRSHUT_POS_COMD	% Open	Changes % to forcibly open/close the active air shutter.	-	NOTE: Override drive parameter: 0-100%
CHARGE_LAMP	No (False)/Yes (True)	Select No (False)/Yes (True) to turn on/off the charging system warning light. Select No (False)/Yes (True) to display/not display the charging system warning indication on the multi-information display.	Under the following conditions: Ignition switch ON (engine off) Idle Racing (not idle)	-
CSTR_VENT_SOL_DUTY	%	NOTE: Displays in the M-MDS but it does not operate.
EGR_COMD	%	Changes % and forcibly drives/stops EGR valve.	Under the following conditions: Idle (no load)	NOTE: Override drive parameter: 0-100%
ENG_COOL_VLV_POS_COMD	° (deg)	Changes ° (deg) and forcibly drives/stops coolant control valve.	Under the following conditions: Ignition switch ON (engine off)	NOTE: Override drive parameter: 0-119°
ENG_RPM_DSD	Rpm	Changes value (Rpm) to forcibly vary engine speed.	Under the following conditions: Idle Racing (not idle)	The use in the following ranges is recommended: Engine coolant temperature 75-95°C {167-203°F} Vehicle stopped Override drive parameter: 550-2, 000 rpm
EX_SHUT_VLV_DSD	° (deg)	Changes ° (deg) and forcibly drives/stops exhaust shutter valve.	Under the following conditions: Ignition switch ON (engine off)	NOTE: Override drive parameter: 0-66°
FAN	%	Changes % and forcibly drives/stops fan control module.	Under the following conditions: Idle	NOTE: Override drive parameter: 0-90%
FP_DUTY	%	Changes % and forcibly drives/stops fuel pump.	Under the following conditions: Ignition switch ON (engine off) Idle Racing (not idle)	WARNING: Do not use the simulation function while the fuel hose between the high pressure fuel pump and fuel pump is removed. NOTE: Override drive parameter: 5-95%
FUEL_PUMP_REQ	Off/On	Changes Off/On and forcibly drives/stops fuel pump.	Under the following conditions: Ignition switch ON (engine off) Idle Racing (not idle)	-
H_SPD_FAN	Off/On	Select Off/On to forcibly drive/stop the cooling fan at high speed.	-	-
INJ	-	Forcibly stops the fuel injectors while the engine is idling.	Under the following conditions: Idle	WARNING: Do not use the simulation function while the vehicle is being driven. Stopping the fuel ejection causes the engine to stall which may cause the brakes to not function.
L_SPD_FAN	Off/On	Select Off/On to forcibly drive/stop the cooling fan at low speed.	-	-
M_SPD_FAN	Off/On	Select Off/On to forcibly drive/stop the cooling fan at middle speed.	-	-
MIL	Off/On	Select Off/On to turn on/off the check engine light.	Under the following conditions: Ignition switch ON (engine off) Idle Racing (not idle)	-
OIL_PRES_SOL	OFF/ON	Select OFF/ON to forcibly drive/stop the engine oil solenoid valve.	-	-
OIL_PUMP_DUTY	% Duty Cycle	Changes % and forcibly drives/stops engine oil solenoid valve.	Under the following conditions: Idle	NOTE: Override drive parameter: 0-100%
PRG_DUTY	%	Changes % and forcibly drives/stops purge solenoid valve.	Under the following conditions: Ignition switch ON (engine off) Idle Racing (not idle)	NOTE: Override drive parameter: 0% Purge solenoid valve: Close Override drive parameter: 100% Purge solenoid valve: Open
WASTEGATE_POS_SIMULATION	%	Changes % and forcibly drives/stops purge wastegate valve.	Under the following conditions: Idle	Vehicle speed: 0 km/h {0 mph} NOTE: Override drive parameter: 0-100%
WHEEL_DRIVE_CTRL_COMD	-	Forcibly drives/stops AWD solenoid built-in coupling component.	Under the following conditions: Ignition switch ON (engine off) Idle Racing (not idle)	NOTE: If the AWD solenoid is forcibly driven, the AWD warning light flashes.