PID/Data Monitor Table [SAS]

PID AND DATA MONITOR PART SPECIFICATION (SAS)

PID (data content)	Units/operation	Operation status (reference)
AB_RES_F_D (Driver-side air bag module (inflator No. 1) resistance)	mOhm	Continuous: 0.99-6.42 ohms
AB_RES_F_P (Passenger-side air bag module (inflator No. 1) resistance)	mOhm	Continuous: 0.81-6.42 ohms
AB2_RES_F_D (Driver-side air bag module (inflator No. 2) resistance)	mOhm	Continuous: 0.99-6.42 ohms
AB2_RES_F_P (Passenger-side air bag module (inflator No. 2) resistance)	mOhm	Continuous: 0.81-6.42 ohms
C_AB_RES_D (Driver-side curtain air bag module resistance low)	mOhm	Continuous: 0.81-6.42 ohms
C_AB_RES_P (Passenger-side curtain air bag module resistance low)	mOhm	Continuous: 0.81-6.42 ohms
DETECT_BAR_RES_A (Partial disconnection detection bar resistance (SAS control module connector No. 1))	ohm	NOTE: Determination of connection/partial connection is performed depending on whether DTC B1011-95: is detected or not. Connector connected: 1 ohm or less Connector partially dis 25.5 o
DETECT_BAR_RES_B (Partial disconnection detection bar resistance (SAS control module connector No. 2))	ohm	NOTE: Determination of connection/partial connection is performed depending on whether DTC B1011-11: is detected or not. Connector connected: 1 ohm or less Connector partially dis 25.5 o
DETECT_BAR_RES_C (Partial disconnection detection bar resistance (SAS control module connector No. 3))	ohm	NOTE: Determination of connection/partial connection is performed depending on whether DTC B1011-12: is detected or not. Connector connected: 1 ohm or less Connector partially dis 25.5 o
DTC_STAT (Number of malfunctions detected)	-	Number of malfunctions detected
FAR_SIDE_AB_RES (Far side air bag module)	mOhm	NOTE: Displayed on M-MDS but does not function.
K_AB_RES_D (Driver-side knee air bag module resistance)	mOhm	Continuous: 0.81-9.85 ohms
K_AB_RES_P (Passenger-side knee air bag module resistance)	mOhm	Continuous: 0.81-9.85 ohms
OCS_CAL_STAT (DTC clearing status of occupant classification sensor control module)	Process started/Normally ended/Failure caused by other command process/Failure caused by abnormal voltage/Failure caused by abnormal measured weight/Fault that depends on over the limit of OCS sensors/Failure caused by timeout/In process/Failed to start/Failure caused by OCS fault	Displays the calibration status of the occupant classification sensor control module.
OCS_DTC_STAT (Calibration status of occupant classification sensor control module)	Process Started/Normally ended/In process/Failed to start/Abnormal end	Displays the DTC clearing status of the occupant classification sensor control module determined by the seat weight sensor.
OCS_STAT (Capacitance status)	Empty/Below Threshold (Small)/Indeterminate/Above Threshold (Large)/No fault because "Process started" or "In process" or "Normal end/Fault that depands on OCS-ECU executing other command/Fault that depends on OCS-ECU abnormal power supply voltage/Fault that depends on Abnormal measured weight of OCS sensors/Fault that depends on over the limit of OCS sensors/Fault that depends on CAL check processing time-out of OCS-ECU/Fault that depends on fault of OCS-ECU and/or sensors/Fault that depends on CAL check processing timeout of SAS-ECU	Displays the capacitance status determined by the seat weight sensor.
R_PRETEN_RES_D (Driver-side rear pre-tensioner seat belt resistance)	mOhm	Continuous: 0.81-6.42 ohms
R_PRETEN_RES_P (Passenger-side rear pre-tensioner seat belt resistance)	mOhm	Continuous: 0.81-6.42 ohms
S_AB_RES_D (Driver-side side air bag module resistance)	mOhm	Continuous: 0.81-9.85 ohms
S_AB_RES_P (Passenger-side side air bag module resistance)	mOhm	Continuous: 0.81-9.85 ohms
S_AB_RES_R_D (Driver-side rear air bag module resistance)	mOhm	Continuous: 0.81-9.85 ohms
S_AB_RES_R_P (Passenger-side rear air bag module resistance)	mOhm	Continuous: 0.81-9.85 ohms
S_BELT_PRETEN_RES_D (Driver-side front pre-tensioner seat belt resistance)	mOhm	Continuous: 0.81-6.42 ohms
S_BELT_PRETEN_RES_P (Passenger-side front pre-tensioner seat belt resistance nominal)	mOhm	Continuous: 0.81-6.42 ohms
S_BELT_REMINDER_P (Passenger-side buckle switch status)	Off/On	An occupant is seated on the passenger-side front seat: On	Passenger-side front seat belt fastened (Passenger-side buckle switch off): Off Passenger-side front seat belt is unfastened (passenger-side buckle switch ON): On
S_BELT_STAT_D (Driver-side buckle switch status)	Not Buckled/Buckled	Driver-side front seat belt fastened (driver-side buckle switch OFF): Buckled Driver-side front seat belt unfastened (driver-side buckle switch ON): Not Buckled
S_BELT_STAT_P (Passenger-side buckle switch status)	Not Buckled/Buckled	Passenger-side front seat belt fastened (Passenger-side buckle switch off): Buckled Passenger-side front seat belt is unfastened (passenger-side buckle switch ON): Not Buckled
SEAT_TRACK_SEN (Seat track position sensor status)	Rearward/Forward	Driver-side front seat in foremost position: Forward Other: Rearward
SEAT_TRACK_STAT (Seat track position sensor malfunction condition)	No Fault/Fault	Seat track position sensor is normal: No Fault Malfunction in seat track position sensor: Fault
SEAT_WEIGHT_P (Occupant weight on passenger-side front seat)	Kg	Displays the occupant weight on the passenger-side front seat.
VPWR (SAS control module power voltage)	V	Ignition switch/main power switched ON: IG1 voltage
WRNG_LAMP_STAT (Air bag/seat belt pre-tensioner system warning light status)	Lamp Off/Lamp On/Lamp Flash at 5 HZ/Plant Mode/Status Unknown	Air bag/seat belt pre-tensioner system warning light turned off: Lamp_Off Air bag/seat belt pre-tensioner system warning light turned on: Lamp_On Air bag/seat belt pre-tensioner system warning light flashing: Plant_Mode Air bag/seat belt pre-tensioner system warning light flashing: Lamp Flash at 5 HZ Air bag/seat belt pre-tensioner system warning light flashing in plant mode: Plant_Mode Air bag/seat belt pre-tensioner system warning light status is unknown: Unknown