LEMON Manuals: Even more car manuals for everyone
Home >> Mazda >> 2024 >> 3 Carbon Turbo, 4D Hatchback >> Repair and Diagnosis >> Accessories & Equipment >> Communication Devices >> On-Board Diagnostic - Door-Electrical Supply Unit (Driver) >> PID/Data Monitor Table

PID/Data Monitor Table

-: Not applicable

PID AND DATA MONITOR PART SPECIFICATION (DOOR_ESU_D)

PID Unit/Operation Data contents
AT_STRAGE_MIRROR_CSTMZ Not Adopted/Off/On  
  • Not Adopted: Personalization feature for power outer mirrors is not applicable.
  • Off: Personalization feature setting for power outer mirrors is off.
  • On: Personalization feature setting for power outer mirrors is on.
BSM_MIRROR_IND_CTRL_D Off/On  
  • Off: Blind spot monitoring (BSM) warning light (driver's side) is turned off.
  • ON: Blind spot monitoring (BSM) warning light (driver's side) is turned on.
BSP_EV_WRNG_L no event/left warning event  
  • no event: Blind spot monitoring (BSM) warning lights are turned off.
  • left warning event: Blind spot monitoring (BSM) warning light (LH) is flashed and blind spot monitoring (BSM) warning light (RH) is turned off.
BSP_EV_WRNG_R no event/right warning event  
  • no event: Blind spot monitoring (BSM) warning lights are turned off.
  • right warning event: Blind spot monitoring (BSM) warning light (RH) is flashed and blind spot monitoring (BSM) warning light (LH) is turned off.
C_DOOR_LCK_SW_D OFF/Lock/Unlock  
  • OFF: Door lock switch (driver's side) is not in lock and unlock.
  • Lock: Door lock switch (driver's side) is in lock.
  • Unlock: Door lock switch (driver's side) is in unlock.
CRANKING_STAT Off/On  
  • Off: Body control module (BCM) does not control cranking at ignition switch ON/main power switch ON.
  • On: Body control module (BCM) controls cranking at ignition switch ON/main power switch ON.
CRASH_SIG Unknown/Normal/Abnormal/Crash  
  • Unknown: Crash signal is not determined.
  • Normal: Crash signal is not received.
  • Abnormal: Error collision signal is received.
  • Crash: Crash signal is received.
CTSY_LAMP_CTRL_STAT OFF/ON  
  • OFF: Courtesy light is turned off.
  • ON: Courtesy light is turned on.
DOOR_CTSY_LAMP Unknown/0%Fade out/100%Fade in  
  • Unknown: Courtesy light condition cannot be detected.
  • 0%Fade out: Courtesy light fades out.
  • 100%Fade in: Courtesy light fades in.
DOOR_G_OPEN_CLOSE_REQ WindowStop/WindowOpen/WindowClose  
  • Window Stop: Not during front door glass operation.
  • Window Open: While front door glass is opening.
  • Window Close: While front door glass is closing.
DOOR_LCK_CTRL_STAT_D OFF/NormalLock/NormalUnlock/2StageUnlock/SuperLock  
  • OFF: All door lock actuators are not operated.
  • Normal Lock: All door lock actuators are operated to lock.
  • Normal Unlock: All door lock actuators are operated to unlock.
  • 2 Stage Unlock All door lock actuators are operated to 2-step unlocking function.
  • Super Lock: All door lock actuators are operated to double locking function.
DOOR_LCK_MSG - Displays the code to unlock doors
DOOR_LCK_ULCK_CTRL_D Not Drive/All Lock/All Super Lock/All UnLock/Only DrvUnLock/Return All Lock  
  • Not Drive: All door lock actuators are not operated.
  • All Lock: All door lock actuators are operated to lock.
  • All Super Lock: All door lock actuators are operated to double locking function.
  • All UnLock: All door lock actuators are operated to unlock.
  • Only DrvUnLock: Driver's door unlock actuator is operated to unlock.
  • Return All Lock: Returns to normal lock condition from double locking function condition.
DOOR_SW_F_D Off/On  
  • Off: Door latch switch (driver's side) is off.
  • On: Door latch switch (driver's side) is on.
DOOR_SW_QF_P Faulty/Undefined/Not within Specification/OK  
  • Faulty: Front door latch switch signal cannot be received.
  • Undefined: Front door latch switch undefined signal is received.
  • Not within Specification: Front door latch switch unspecified signal is received.
  • OK: Front door latch switch signal can be received normally.
DOOR_SW_QF_R Faulty/Undefined/Not within Specification/OK  
  • Faulty: Rear door latch switch signal cannot be received.
  • Undefined: Rear door latch switch undefined signal is received.
  • Not within Specification: Rear door latch switch unspecified signal is received.
  • OK: Rear door latch switch signal can be received normally.
DOOR_SW_STAT_F_P Door Closed/Door Ajar  
  • Door Closed: Front door (passenger's side) is closed.
  • Door Ajar: Front door (passenger's side) is open.
DOOR_SW_STAT_L/R Door Closed/Door Ajar  
  • Door Closed: Rear door (LH) is closed.
  • Door Ajar: Rear door (LH) is open.
DOOR_SW_STAT_R/R Door Closed/Door Ajar  
  • Door Closed: Rear door (RH) is closed.
  • Door Ajar: Rear door (RH) is open.
DOOR_SW_STAT_T/LGT Faulty/Undefined/Not within Specification/OK  
  • Faulty: Trunk lid latch switch/liftgate latch switch signal from electrical supply unit (ESU) cannot be received.
  • Undefined: Trunk lid latch switch/liftgate latch switch undefined signal from electrical supply unit (ESU) is received.
  • Not within Specification: Trunk lid latch switch/liftgate latch switch unspecified signal from electrical supply unit (ESU) is received.
  • OK: Trunk lid latch switch/liftgate latch switch signal from electrical supply unit (ESU) can be received normally.
DOOR_ULCK_REQ All Lock/All Super Lock/All UnLock/Not Drive/Only DrvUnLock/Return All Lock  
  • All Lock: All door lock actuators are operated to lock.
  • All Super Lock: All door lock actuators are operated to double locking function.
  • All UnLock: All door lock actuators are operated to unlock.
  • Not Drive: All door lock actuators are not operated.
  • Only DrvUnLock: Driver's door unlock actuator is operated to unlock.
  • Return All Lock: Returns to normal lock condition from double locking function condition.
DRIVE_POS_STAT OFF/Completed/Reject/NoNeed  
  • OFF: Position memory system is off.
  • Completed: Adjustment to programmed position by position memory system is completed.
  • Reject: Adjustment to programmed position by position memory system is not possible.
  • No Need: Adjustment from current position is unnecessary.
DRIVER_NUM Driver 1 (Memory SW1)/Driver 2 (Memory SW2)/Driver 3 (Transmitter 1)/Driver 4 (Transmitter 2)/Driver 5 (Transmitter 3)/Driver 6 (Transmitter 4)/Driver 7 (Transmitter 5)/Driver 8 (Transmitter 6)  
  • Driver 1 (Memory SW1): Seat position programmed to memory 1 switch is called up.
  • Driver 2 (Memory SW2): Seat position programmed to memory 2 switch is called up.
  • Driver 3 (Transmitter 1): Seat position programmed to remote transmitter No. 1 is called up.
  • Driver 4 (Transmitter 2): Seat position programmed to remote transmitter No. 2 is called up.
  • Driver 5 (Transmitter 3: Seat position programmed to remote transmitter No. 3 is called up.
  • Driver 6 (Transmitter 4): Seat position programmed to remote transmitter No. 4 is called up.
  • Driver 7 (Transmitter 5): Seat position programmed to remote transmitter No. 5 is called up.
  • Driver 8 (Transmitter 6): Seat position programmed to remote transmitter No. 6 is called up.
ERASE_REQ No Action/Erase Request  
  • No Action: Deletion of programmed seat position is not necessary.
  • Erase Request: Deletion of programmed seat position is necessary.
FOLD_MIRROR_CTRL_D OFF/Open/Close  
  • OFF: Retract/return motor (driver's side) does not operate.
  • Open: Retract/return motor (driver's side) operates in the return direction.
  • Close: Retract/return motor (driver's side) operates in the retract direction.
GEAR_REVERSE Off/On  
  • Off: Selector lever is not operated to the R position (AT/ATX)/Shift lever is not operated to the reverse position (MT/MTX).
  • On: Selector lever is operated to the R position (AT/ATX)/Shift lever is operated to the reverse position (MT/MTX).
ID_STAT_1 Not Complete/Complete  
  • Not Complete: Programming of remote transmitter ID data between body control module (BCM) and door-electrical supply unit is not completed.
  • Complete: Programming of remote transmitter ID data between body control module (BCM) and door-electrical supply unit is completed.
ID_STAT_2 Unknown/NG/OK  
  • Unknown: Verification of remote transmitter ID data between body control module (BCM) and door-electrical supply unit cannot be determined.
  • NG: Remote transmitter ID data between body control module (BCM) and door-electrical supply unit is verified and not determined to be programmed remote transmitter.
  • OK: Remote transmitter ID data between body control module (BCM) and door-electrical supply unit is verified and determined to be programmed remote transmitter.
ID_STAT_3 OK/NG  
  • OK: Door unlock request is received.
  • NG: Authorization of remote transmitter fails 3 times or more and acceptance of door unlock request is inhibited.
ID_STAT_4 0/1/2/3 or More  
  • 0: Remote transmitter ID data between body control module (BCM) and door-electrical supply unit is verified and determined to be programmed remote transmitter.
  • 1: Remote transmitter ID data between body control module (BCM) and door-electrical supply unit is verified and determined not to be programmed remote transmitter 1 time.
  • 2: Remote transmitter ID data between body control module (BCM) and door-electrical supply unit is verified and determined not to be programmed remote transmitter 2 times.
  • 3 or More: Remote transmitter ID data between body control module (BCM) and door-electrical supply unit is verified and determined not to be programmed remote transmitter more than 3 times.
ILLMI_MODE Unknown/OFF, daylight mode/ON, daylight mode  
  • Unknown: Panel light illumination request signal is not determined.
  • OFF, daylight mode: Panel light illumination request signal is not received.
  • ON, daylight mode: Panel light illumination request signal is received.
ILLMI_POWER_CTRL_STAT OFF/ON Displays illumination power supply condition
IND_ILLMI OFF/ON  
  • OFF: Indirect illumination is not illuminated.
  • ON: Indirect illumination is illuminated.
INDIRECT_ILLMI Unknown/0%Fade out/100%Fade in/KINDIRECTILLUMRATE_DARK% Fade/KINDIRECTILLUMRATE_MEDIUM% Fade/KINDIRECTILLUMRATE_BLIGHT% Fade  
  • Unknown: Interior light illumination condition cannot be detected.
  • 0% Fade out: Interior light is off.
  • 100% Fade in: Interior light is on.
  • KINDIRECTILLUMRATE_DARK% Fade: Brightness of interior light illumination is dark.
  • KINDIRECTILLUMRATE_MEDIUM% Fade: Brightness of interior light illumination is normal.
  • KINDIRECTILLUMRATE_BLIGHT% Fade: Brightness of interior light illumination is bright.
LLINK_SW Unlock/Neutral/Lock/Failure  
  • Unlock: Front door lock-link switch (driver's side) is in unlock.
  • Neutral: Front door lock-link switch (driver's side) is not in lock and unlock.
  • Lock: Front door lock-link switch (driver's side) is in lock.
  • Failure: Front door lock-link switch (driver's side) has a malfunction.
LLINK_SW_LCK_D Off/On  
  • Off: Front door lock-link switch (driver's side) is in unlock.
  • On: Front door lock-link switch (driver's side) is in lock.
LLINK_SW_ULCK_D Off/On  
  • Off: Front door lock-link switch (driver's side) is in lock.
  • On: Front door lock-link switch (driver's side) is in unlock.
MIRROR_ADJ_CTRL_STAT_D OFF/Up/Down/Left/Right Up/down adjustment motor (driver's side) and left/right adjustment motor (driver's side) output signal
  • OFF: Mirror surface adjustment door mirror motor (driver's side) is not operated in any direction.
  • Up: Up/down adjustment motor (driver's side) operates upward.
  • Down: Up/down adjustment motor (driver's side) operates downward.
  • Left: Left/right adjustment motor (driver's side) operates leftward.
  • Right: Left/right adjustment motor (driver's side) operates rightward.
MIRROR_ADJ_SEL_SW OFF/L Side ON/R Side ON  
  • OFF: Left/right selection switch is off.
  • L Side ON: Left selection switch is on.
  • R Side ON: Right selection switch is on.
MIRROR_ADJ_SEL_SW_L OFF/ON  
  • OFF: Left selection switch illumination is not illuminated.
  • ON: Left selection switch illumination is illuminated.
MIRROR_ADJ_SEL_SW_R OFF/ON  
  • OFF: Right selection switch illumination is not illuminated.
  • ON: Right selection switch illumination is illuminated.
MIRROR_ADJ_SW OFF/Up/Down/Left/Right  
  • OFF: All switches are turned off.
  • Up: Upward switch is turned on.
  • Down: Downward switch is turned on.
  • Left: Leftward switch is turned on.
  • Right: Rightward switch is turned on.
MIRROR_DEF_CTRL_STAT_D Off/ON Heated outer mirror filaments output signal
  • Off: Heated outer mirror (driver's side) filaments are not heated to warm.
  • On: Heated outer mirror (driver's side) filaments are heated to warm.
MIRROR_FOLD_SW Off/On  
  • On: Power outer mirror retract/return switch is pressed
  • Off: Conditions other than above
MIRROR_TURN_LAMP_CTRL_D Off/ON Side turn light output signal
  • Off: Side turn light (driver's side) is turned off.
  • On: Side turn light (driver's side) is turned on.
PNL_LGHT_CTRL_B_LVL % Displays brightness to turn on panel lights
PNL_LGHT_CTRL_DIM_CANCEL Unknown/OFF/ON  
  • Unknown: Dimmer cancel signal is not determined.
  • OFF: Dimmer cancel signal is not received.
  • ON: Dimmer cancel signal is received.
POWER_STAT OFF/ACC/ON/CRANK Displays ignition/main power status.
PWIND_CUT_SW Off/On  
  • Off: Power-cut switch is off.
  • On: Power-cut switch is on.
PWIND_MAIN_DOWN_SW_F_D OFF/ON/Water Immersion  
  • OFF: Driver's switch is not operated for open operation by power window main switch.
  • ON: Driver's switch is operated for open operation by power window main switch.
  • Water Immersion: Driver's switch is sunk in water.
PWIND_MAIN_SW_F_D OFF/Manual Up/Auto Up/Auto Down/Water Immersion  
  • OFF: Driver's switch is not operated by power window main switch.
  • Manual Up: Driver's switch is operated for a manual close operation by power window main switch.
  • Auto Up: Driver's switch is operated for an auto close operation by power window main switch.
  • Auto Down: Driver's switch is operated for an auto operation by power window main switch.
  • Water Immersion: Driver's switch is sunk in water.
PWIND_MAIN_SW_F_P OFF/Manual Up/Auto Up/Manual Down/Auto Down/GND Short  
  • OFF: Passenger's side switch is not operated by power window main switch.
  • Manual Up: Passenger's side switch is operated for a manual close operation by power window main switch.
  • Auto Up: Passenger's side switch is operated for an auto close operation by power window main switch.
  • Manual Down: Passenger's side switch is operated for a manual open operation by power window main switch.
  • Auto Down: Passenger's side switch is operated for an auto operation by power window main switch.
  • GND Short: Short to ground circuit malfunction is received from passenger's side switch.
PWIND_MAIN_SW_ILLMI Off/ON  
  • Off: Power window main switch illumination is not illuminated.
  • ON: Power window main switch illumination is illuminated.
PWIND_MAIN_SW_L/R OFF/Manual Up/Auto Up/Manual Down/Auto Down/GND Short  
  • OFF: Rear side switch (LR) is not operated by power window main switch.
  • Manual Up: Rear side switch (LR) is operated for a manual close operation by power window main switch.
  • Auto Up: Rear side switch (LR) is operated for an auto close operation by power window main switch.
  • Manual Down: Rear side switch (LR) is operated for a manual open operation by power window main switch.
  • Auto Down: Rear side switch (LR) is operated for an auto operation by power window main switch.
  • GND Short: Short to ground circuit malfunction is received from rear side switch (LR).
PWIND_MAIN_SW_R/R OFF/Manual Up/Auto Up/Manual Down/Auto Down/GND Short  
  • OFF: Rear side switch (RR) is not operated by power window main switch.
  • Manual Up: Rear side switch (RR) is operated for a manual close operation by power window main switch.
  • Auto Up: Rear side switch (RR) is operated for an auto close operation by power window main switch.
  • Manual Down: Rear side switch (RR) is operated for a manual open operation by power window main switch.
  • Auto Down: Rear side switch (RR) is operated for an auto operation by power window main switch.
  • GND Short: Short to ground circuit malfunction is received from rear side switch (RR).
PWIND_MOTOR_STAT_F_D OFF/Open/Close Front power window motor (driver's side) output signal
  • OFF: Front power window motor (driver's side) does not rotate.
  • Open: Front power window motor (driver's side) performs a open operation.
  • Close: Front power window motor (driver's side) performs a close operation.
PWIND_MOTOR_STAT_R_D OFF/Open/Close Rear power window motor (driver's side) output signal
  • OFF: Rear power window motor (driver's side) does not rotate.
  • Open: Rear power window motor (driver's side) performs a open operation.
  • Close: Rear power window motor (driver's side) performs a close operation.
PWIND_POS_COUNT_F_D Count Displays the number of rotation (front power window motor (driver's side))
PWIND_POS_COUNT_R_D Count Displays the number of rotation (rear power window motor (driver's side))
PWIND_SUB_DOWN_SW_R_D OFF/ON/Water Immersion  
  • OFF: Rear power window subswitch (driver's side) is not operated for open operation by power window main switch.
  • ON: Rear power window subswitch (driver's side) is operated for open operation by power window main switch.
  • Water Immersion: Rear power window subswitch (driver's side) is sunk in water.
PWIND_SUB_SW_ILLMI_R_D OFF/ON  
  • OFF: Rear power window subswitch (driver's side) illumination is not illuminated.
  • ON: Rear power window subswitch (driver's side) illumination is illuminated.
PWIND_SUB_SW_R_D OFF/Manual Up/Auto Up/Auto Down/Water Immersion  
  • OFF: Rear power window subswitch (driver's side) is not operated.
  • Manual Up: Rear power window subswitch (driver's side) is operated for a manual close operation.
  • Auto Up: Rear power window subswitch (driver's side) is operated for an auto close operation.
  • Auto Down: Rear power window subswitch (driver's side) is operated for an auto open operation.
  • Water Immersion: Rear power window subswitch (driver's side) is sunk in water.
R_DEF_CTRL_STAT Rear defogger Off/Rear defogger On  
  • Rear defogger Off: Rear window defogger operation request signal from climate control unit is not received.
  • Rear defogger On: Rear window defogger operation request signal from climate control unit is received.
RECALL_REQ No Action/Recall Request  
  • No Action: Seat position recall is not requested.
  • Recall Request: Seat position recall is requested.
RECORD_REQ No Action/Record Request  
  • No Action: Seat position programming is not requested.
  • Record Request: Seat position programming is requested.
REMOTE_MIRROR_POS_X_D V Displays input value for variable resistance sensor of left/right adjustment motor (driver's side).
REMOTE_MIRROR_POS_Y_D V Displays input value for variable resistance sensor of up/down adjustment motor (driver's side).
RES_CTRL_STAT Remote Start Off/Remote Start On  
NOTE:
  • It is displayed, however, if an accessory part is installed, it cannot be used.
RLY_STAT_B3_B4 +B3/+B4  
  • +B3: Power is supplied from power supply terminal (BATT3).
  • +B4: Power is supplied from power supply terminal (BATT4).
ROOM_FUSE_STAT Without Room Fuse/With Room Fuse/Unused/Unknown Displays the F27 25A fuse condition.
SHIFT Initial Value/1st/2nd/3rd/4th/5th/6th/7th/8th/9th/Neutral/Reverse/Park/Unknown Hex/Invalid Hex  
  • Initial Value: Shift lever is between two positions.
  • 1st: Shift lever is in 1st position.
  • 2nd: Shift lever is in 2nd position.
  • 3rd: Shift lever is in 3rd position.
  • 4th: Shift lever is in 4th position.
  • 5th: Shift lever is in 5th position.
  • 6th: Shift lever is in 6th position.
  • 7th: Shift lever is in 7th position.
  • 8th: Shift lever is in 8th position.
  • 9th: Shift lever is in 9th position.
  • Neutral: Shift lever is in N position.
  • Reverse: Shift lever is in R position.
  • Park: Shift lever is in P position.
  • Unknown Hex: Shift lever position is not determined.
  • Invalid Hex: Shift lever position signal has error.
TURN_IND_L OFF/ON  
  • OFF: Turn switch LH signal is not received.
  • ON: Turn switch LH signal is received.
TURN_IND_R OFF/ON  
  • OFF: Turn switch RH signal is not received.
  • ON: Turn switch RH signal is received.
TURN_LAMP_KODO_REQ OFF/ON  
  • OFF: Turn light request signal is not received.
  • ON: Turn light request signal is received.
VPWR V Displays voltage at door-electrical supply unit power supply terminal (BATT1)
VPWR_B2 V Displays voltage at door-electrical supply unit power supply terminal (BATT2)
VPWR_B3 V Displays voltage at door-electrical supply unit power supply terminal (BATT3)
VPWR_B4 V Displays voltage at door-electrical supply unit power supply terminal (BATT4)
scientia non olet · About LEMON Manuals